Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Reusing treble buttons?  (Read 1143 times)

0 Members and 2 Guests are viewing this topic.

Aaron Wildman

  • Member
  • *
  • Offline Offline
  • Posts: 36
Reusing treble buttons?
« on: August 27, 2024, 02:33:02 PM »

My hohner has a mix of buttons on the treble side.  There seem to be two different crowns.  Since it is c#/d, I would like to at least have the D row with the same style of crown.  This would mean swapping 5 or 6 buttons between levers.

If I use the soldering iron method for removal, will the buttons be able to reinstall without problems?  Any suggestions otherwise?  I don't want to pay $4 per button to replace.
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Reusing treble buttons?
« Reply #1 on: August 27, 2024, 04:08:06 PM »

I've recently been swapping a set of MOP buttons from an old 3 voice club to fit onto my latest 1 row. I just knocked them off using a vice, and pressed them back on with a pair of Vise Grips and some cloth so as not to damage the top surface.
Worked a treat, and no heat involved.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Reusing treble buttons?
« Reply #2 on: August 27, 2024, 07:22:37 PM »

Don't know about re-using, but for removing & installing I was not happy with the soldering iron.
Instead, a dremel versa-flame & a home-made brass button shield seem to be working a lot better.


Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reusing treble buttons?
« Reply #3 on: August 27, 2024, 08:40:54 PM »

No heat is required.  Support below the button on both sides (such as a vice mentioned by Winston). Snug the vice up to remove play but not grip the lever, then a sharp tap on the top side of the lever should remove it.  Easiest if the mechanism is completely dismantled.
If you do resort to heat and the button no longer holds then you may need to use a spot of epoxy.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Aaron Wildman

  • Member
  • *
  • Offline Offline
  • Posts: 36
Re: Reusing treble buttons?
« Reply #4 on: August 27, 2024, 11:20:40 PM »

Please don't make me disassemble the mechanism.  I don't want to go down the rabbit hole of updating springs etc, and once it is apart, I will feel obligated. 

Siince there are some buttons on the inner row that have to be removed, I wil have to get creative.  Perhaps a slot sawed into the end of a dowel (so it slips over the lever but still supports the button) or something.

Thanks for the direction, gents.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal