Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Specific Hohner Bass Mechanism advice  (Read 2195 times)

0 Members and 1 Guest are viewing this topic.

Aaron Wildman

  • Member
  • *
  • Offline Offline
  • Posts: 36
Specific Hohner Bass Mechanism advice
« on: September 05, 2024, 12:32:36 AM »

I have one bass button on my presswood Hohner that is higher than the others, by about 4 mm.  Upon opening the mechanism, I find that the key has been bent in several different places, and now has a compound offset instead of a single offset.  Of course, I plan on straightening it close to its original shape.  I just need to know what the shape is.  Can anybody share a pic of theirs?  Or at least tell me if all the offset keys have roughly the same amount of offset, with the offset only on a single plane?  Note:  all the other keys seem to be relatively intact

Additionally, the lever to which this particular key attaches (the lowest lever, closest to the knee when playing) is out of line with the 3 other similar levers, by approx the aforementioned 4mm.  Is there any reason not to bend this back in alignment with the other keys?  Again, I have no idea if these were originally designed with the current alignment or not.

Final part of this compound question:  Roughly what button height should I be shooting for?

I'll see about posting pics.
« Last Edit: September 05, 2024, 12:34:23 AM by Aaron Wildman »
Logged

Aaron Wildman

  • Member
  • *
  • Offline Offline
  • Posts: 36
Logged

Nigel Champion

  • Member
  • *
  • Offline Offline
  • Posts: 18
Re: Specific Hohner Bass Mechanism advice
« Reply #2 on: September 05, 2024, 04:22:52 AM »

Hi Aaron. Is this of any help?

Logged

Nigel Champion

  • Member
  • *
  • Offline Offline
  • Posts: 18
Re: Specific Hohner Bass Mechanism advice
« Reply #3 on: September 05, 2024, 06:29:02 AM »

Here's a couple of photos of the one you're having trouble with.
Ignore the Blutak.
It should only bend in the one plane. Maybe a previous owner put them in wrongly!!!
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Specific Hohner Bass Mechanism advice
« Reply #4 on: September 05, 2024, 08:38:50 AM »

The steel those levers are made from is very soft. As long as it’s not rubbing on nearby levers just bend enough the get the button sitting straight.  Then adjust the height.  First check that the button is pushed fully onto the end of the rod. It should butt up to the shoulders on the rod.  Then adjust the height by bending the upright lever at the opposite end from the button. To do this hold the pallet down firmly and push the lever till you have reduced the button height sufficiently.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Aaron Wildman

  • Member
  • *
  • Offline Offline
  • Posts: 36
Re: Specific Hohner Bass Mechanism advice
« Reply #5 on: September 05, 2024, 11:15:23 PM »

About half of the buttons are ~1mm above the shoulders.  I will put them in a vise and tap them in fully.

@Nigel - That picture does help a bit, but my mechanism could be slightly different.  It does appear that most of my keys with a sideways offset have less bend/offset than yours.  Would you say that your shafts are all parallel from the lever connection to the offset, and then they are all parallel once again between the offset and the button? In other words, it would make sense that all of the shafts would be parallel as much as possible, and only diverge for the individual offsets.  Is this correct?   Any chance you can get a straight-on end pic so I can judge the angle of the these other keys?

Thanks, guys!
Logged

Aaron Wildman

  • Member
  • *
  • Offline Offline
  • Posts: 36
Re: Specific Hohner Bass Mechanism advice
« Reply #6 on: September 10, 2024, 09:28:16 PM »

Upon further investigating, I have found that the keys were indeed put into the accordion in the wrong order.  Some of them were even flipped around (hinge loop was facing the wrong way on at least two keys)  This explains how the keys have been at mismatching heights. Based on the advice here, and by reviewing Lester's videos, it seems obvious that each of the two rows seem to have two distinct key bending styles.  The outer row seems to have lateral bends, while the inner row seems to have vertical bends.  This is most definitely not the way my bass end was when I took it apart. 

Screen grab from Lester's video:  https://ibb.co/rdx7mMT

Now, I have a better direction to aim for with the key bending, but it also means that I will have to bend more keys - keys that I thought were fine have had the bends [mostly] removed.  Keep your fingers crossed that nothing breaks when I attempt putting these keys in the proper configuration.

I don't know if this is worse than the hockey tape slathered all over the bellows or not, but it is just about as annoying.

Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal