Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Stiff stop  (Read 4193 times)

0 Members and 1 Guest are viewing this topic.

Bob Ellis

  • Hero?....Where's my medal, then?
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2878
  • Ain't I cute?
Stiff stop
« on: December 03, 2009, 08:53:05 PM »

As I have mentioned in another thread, I have just taken delivery of a Cajun four-stop one-row. The box is brand new, so the bellows are a bit stiff, but this will probably ease with playing (hanging it with the bellows open for a few hours should also help). However, one of the stops on the top is VERY stiff. Any suggestions of how I might free it up a bit without damaging the box?
Logged
Bob in beautiful Wensleydale, Les Panards Dansants, Crook Morris and the Loose Knit Band.
Clément Guais 3-row D/G/acc.; Castagnari 1914 D/G; Karntnerland Steirische 3-row G/C/F; Ellis Pariselle 2.6-row D/G/acc.; Gabbanelli Compact 2-row D/G with lots of bling, pre-war Hohner Bb/F; Acadian one-row in D.

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Stiff stop
« Reply #1 on: December 03, 2009, 10:02:59 PM »

Hi Bob

On this style of box you can't remove the reed blocks to get at the stop slides as the blocks are glued in place.
Has it come directly from Louisiana? It's very humid down there and I've often had to leave Cajun boxes in the airing cupboard for a while to dry the wood out a bit.
Play it in a dry, warm environment getting plenty of air through it and keep moving the stop up and down.
Hopefully this shoud eventually cure the problem.
My Clippers are built along the same lines and the stops are usually fairly stiff to begin with but ease off with regular playing.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

triskel

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3290
Re: Stiff stop
« Reply #2 on: December 04, 2009, 12:36:37 AM »


I wonder if the offending stopper might have got slightly bent in transit ???, that can cause the problem you describe.

Mind you, my experience of Louisiana makers has been that they tell you not to use the stops anyway...  :o

Bob Ellis

  • Hero?....Where's my medal, then?
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2878
  • Ain't I cute?
Re: Stiff stop
« Reply #3 on: December 04, 2009, 01:17:06 AM »

Rees: the box came from a guy in Illinois who had over-extended himself financially in buying it. He does not appear to have had it long or played it much (if at all) because it was sold as 'brand new' and looks it. Hopefully giving it plenty of exercise in a centrally-heated house will ease the stiff stop, as you say.

Triskel: I've examined the offending stop closely and, as far as I can tell, it hasn't been bent in transit. Can you explain why Louisiana makers advise not using the stops? Is this because they think everything should be played with all the stops open?

That raises another question: should all the stops be closed when I am not playing the box, or doesn't it matter?
Logged
Bob in beautiful Wensleydale, Les Panards Dansants, Crook Morris and the Loose Knit Band.
Clément Guais 3-row D/G/acc.; Castagnari 1914 D/G; Karntnerland Steirische 3-row G/C/F; Ellis Pariselle 2.6-row D/G/acc.; Gabbanelli Compact 2-row D/G with lots of bling, pre-war Hohner Bb/F; Acadian one-row in D.

triskel

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3290
Re: Stiff stop
« Reply #4 on: December 04, 2009, 01:34:02 AM »

Triskel: I've examined the offending stop closely and, as far as I can tell, it hasn't been bent in transit.

Trouble is, it may not be readily apparent - sometimes turning the knob slightly can ease things, if it's an alignment problem. But it may simply be that the wooden slider is too tight...

Quote
Can you explain why Louisiana makers advise not using the stops? Is this because they think everything should be played with all the stops open?

That's a major reason, yes.

Quote
That raises another question: should all the stops be closed when I am not playing the box, or doesn't it matter?

But they're also worried about the stops getting loose, unnecessarily, where they go through the holes in the top.

Personally, I find it makes more sense to play "on all four" all the time if your box is in Cajun tuning, but I'd sometimes use them if there's some tremolo on one set of reeds (like on my new one), because then you (literally) have more tonal variety to play with...

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Stiff stop
« Reply #5 on: December 04, 2009, 08:02:03 AM »

Rees: the box came from a guy in Illinois who had over-extended himself financially in buying it. He does not appear to have had it long or played it much (if at all) because it was sold as 'brand new' and looks it. Hopefully giving it plenty of exercise in a centrally-heated house will ease the stiff stop, as you say.

Triskel: I've examined the offending stop closely and, as far as I can tell, it hasn't been bent in transit. Can you explain why Louisiana makers advise not using the stops? Is this because they think everything should be played with all the stops open?

That raises another question: should all the stops be closed when I am not playing the box, or doesn't it matter?

Bob, a few ideas:
Have you opened up the box yet? You can open up the treble end by removing the two cross-head screws at the top and bottom of the end frame. Make sure you have the correct size screwdriver. Once opened up, you will be able to see the reed blocks and the stop/slider assembly. The steel shafts of the stops pass through holes in the end frame and screw into 4 squarish wooden blocks which are the slider mounts. Attached (glued) to the slider mounts are the slider strips which probably will be thin (delicate) strips of plywood which pass beneath the reed blocks in a thin gap. Holes in the sliders control the airflow to the reed chambers.

I've attached a photo of the interior of my Stowmarket box when it was under construction. You can see the square slider mounts on the RH side of the photo, although the stops themselves have not yet been fitted. The slider strips can be seen extending and disappearing underneath the reed blocks, to re-emerge at the LH end.  

A stiff stop will be most likely caused by one of two reasons; (a) the steel stop shaft is a tight fit in the end frame, or (b) the slider strip is too tightly gripped beneath the reed blocks. In both cases, gentle, repeated, working up and down may well free things up. Additionally in the case of (a), you could rub candle wax on to the shaft and work it up and down to help reduce friction. It is also possible that a slightly bent steel shaft will cause stiffness where it passes through the end frame.

In the case of (b), this is more difficult because, as Rees has said, the reed blocks are glued into position and so cannot be removed to access the slider strips. The slider may be stiff because it has a rough surface - ideally it should have been sanded, burnished and waxed smooth before gluing the reed blocks in place. Working the slider up and down to gradually polish and ease the surfaces which are in contact is now the only way of easing the stiffness. It may be better to do this by gripping with your fingers on the square slider mount, rather than using the stop knob; some of the stop shaft axes are off-set from the slider axes, therefore working the stop up and down may not direct the axis of motion truly parallel to the slider axis.

Good luck with whatever you do. Go carefully, as damage or breakage of the slider strip is serious, and is not easily repaired or replaced.

Your other query was about storage of the instrument. Personally I prefer to push the stops in after playing; I think they are less vulnerable to getting knocks and bent in that position.
« Last Edit: December 04, 2009, 08:04:32 AM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Stiff stop
« Reply #6 on: December 04, 2009, 09:30:48 AM »

Most Cajun players that I have spoken to insist that the stops are only used when tuning the instrument!

As Triskel says, use the stops for tonal variation. I sometimes get bored with the full-bore sound and often play with only the two MM stops open.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Stiff stop
« Reply #7 on: December 04, 2009, 09:53:20 AM »

As Triskel says, use the stops for tonal variation. I sometimes get bored with the full-bore sound and often play with only the two MM stops open.
Hooray!  (:)
I thought I was the only person who used different stop combinations.  I love the L and H together.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Stiff stop
« Reply #8 on: December 04, 2009, 10:33:19 AM »

Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Bob Ellis

  • Hero?....Where's my medal, then?
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2878
  • Ain't I cute?
Re: Stiff stop
« Reply #9 on: December 04, 2009, 10:45:34 AM »

Thanks for the advice, lads. I think I shall start by following Rees's advice about playing it in and letting it adjust to a drier climate, whilst working the stop in the hope that it will ease. If there is no significant improvement in the next couple of weeks, I shall try candle wax, as Steve suggests, or perhaps graphite might do the trick.
Logged
Bob in beautiful Wensleydale, Les Panards Dansants, Crook Morris and the Loose Knit Band.
Clément Guais 3-row D/G/acc.; Castagnari 1914 D/G; Karntnerland Steirische 3-row G/C/F; Ellis Pariselle 2.6-row D/G/acc.; Gabbanelli Compact 2-row D/G with lots of bling, pre-war Hohner Bb/F; Acadian one-row in D.

Bananayogi

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 147
Re: Stiff stop
« Reply #10 on: December 04, 2009, 11:01:45 AM »

Bob -

The seller knew that stop was sticky. He has been trying to sell it for a little while:

http://pub21.bravenet.com/forum/static/show.php?usernum=1722942123&frmid=16&msgid=939386&cmd=show

He reckoned he had solved it with graphite, but really - just leave all the stops up all the time!

Nice box, by the way. Congrats on the purchase. If I didn't already have a nice Cajun box I would have been tempted.
Logged
Larry Miller Bon Cajun in C, A/D/G Handry, far too many Hohners and a Streb.

triskel

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3290
Re: Stiff stop
« Reply #11 on: December 09, 2009, 02:05:16 PM »

  I love the L and H together.

Pervert

I like 3 "straight" octaves of LMH myself, or sometimes a bit of MM, but best of all is going all the way on LMMH!

triskel

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3290
Re: Stiff stop
« Reply #12 on: December 09, 2009, 02:10:08 PM »

... one of the stops on the top is VERY stiff. Any suggestions of how I might free it up a bit without damaging the box?

If it was mine, I think I'd unscrew the stop-knob and it's metal shaft from the wooden block on the slider, inside the box. You will then very quickly find out if the sticking is in the slide, or in the stop-knob assembly.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Stiff stop
« Reply #13 on: December 09, 2009, 03:09:03 PM »

... one of the stops on the top is VERY stiff. Any suggestions of how I might free it up a bit without damaging the box?

If it was mine, I think I'd unscrew the stop-knob and it's metal shaft from the wooden block on the slider, inside the box. You will then very quickly find out if the sticking is in the slide, or in the stop-knob assembly.
If you decide to do this, open up the box first and make sure that you only do the unscrewing whilst holding the wooden block slider mount firmly, so that it cannot twist during the unscrewing. Otherwise you risk putting torsion on the slider strip which could cause damage to it.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Bob Ellis

  • Hero?....Where's my medal, then?
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2878
  • Ain't I cute?
Re: Stiff stop
« Reply #14 on: December 10, 2009, 12:12:44 AM »

Thanks, Triskel and Steve, for the advice. It may come to that, but I am going to stick with working it up and down for now - at least until the maple from which the box is made has had time to adjust to the temperature conditions in my home. I think it is beginning to ease a bit. If I continue to work it, I hope that it will continue to ease; alternatively, working it up and down may solve the problem by giving me muscles like Samson!  ::)

Apart from the stiff stop, the box is a joy to play and has a beautiful and LOUD tone. Thanks to this box, I have made more progress in playing Cajun-style in the last week than I had done in the previous three years. I'm still a novice when it comes to Cajun music, but I am having a great time learning. Someone asked me to post a picture of the instrument, so here it is.
Logged
Bob in beautiful Wensleydale, Les Panards Dansants, Crook Morris and the Loose Knit Band.
Clément Guais 3-row D/G/acc.; Castagnari 1914 D/G; Karntnerland Steirische 3-row G/C/F; Ellis Pariselle 2.6-row D/G/acc.; Gabbanelli Compact 2-row D/G with lots of bling, pre-war Hohner Bb/F; Acadian one-row in D.
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal