Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Upside down bass reed mounting?  (Read 4621 times)

0 Members and 1 Guest are viewing this topic.

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Upside down bass reed mounting?
« on: September 22, 2024, 05:51:04 PM »

Hi All.

Your thoughts are very welcome on the following question:
Can bass reeds be mounted upside down on the reedblocks? I.e. tip of the reed facing the fondo.

I know that piccollo reeds are often mounted this way and it works for them. I am also aware that helikon reeds are sometimes mounted flat without any significant issues.

I'm putting helikon bass into my squeezebox build. The longest reedplate is 90mm  :-*, so flat mount is out of question, and I don't have the space for a 90 degree winkelbass mount, so the blocks have to be mounted in the conventional upright fashion.
Everything is quite tight, and I'm left with ~16mm of clearance between the lowest reeds and the inside edges of the bellows. I haven't got a clue if that is enough for helikon bass or not, but it looks very tight. So I had a bright idea: what if I mounted the bass reeds upside down? This way the swinging tip is going to be below the bellows folds, and there's a few cm of clearance to the box walls.
Any issues that you're aware of that can make this a non-starter?

Thank you.
« Last Edit: September 22, 2024, 06:18:14 PM by mChavez »
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Upside down bass reed mounting?
« Reply #1 on: October 01, 2024, 07:17:38 AM »

Nobody likes to think outside the box about the insides of the box then?  ;D

I decided to try out the gravity-defying upside-down mount. Unfortunately, it will be a few months before I can report back whether it's a success or a fail.
Logged

Blenchy

  • Blenchy
  • Good talker
  • **
  • Offline Offline
  • Posts: 74
  • What do you mean it's upside down?
Re: Upside down bass reed mounting?
« Reply #2 on: October 01, 2024, 10:15:46 AM »

Putting Helikon basses into one of my melodeons has been on my mind a while so I'll be eager to see how this turns out for you!

I'm sure that one of the small old unbranded piano accordions I've fettled before has bass plates upside down... I'll see if I can fish out the photo or even the box as I think the bass end is still kicking around in my workshop. It had wonderful big brass reeds iirc.

On a side note, where do you get your bass Helikon reeds from? I'm unsure where to start to try and get some.

Thank you!
Logged
David Blench - Sheffield

Hohner Pokerwork and Laurel D/G, 3 Voice Galotta D/G, Old 12 bass Hohner Bb/Eb, 4 Voice "Foreign" C one row. Some concertinas and many more boxes in bits

Part of Handsworth Sword and Rumworth Morris

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Upside down bass reed mounting?
« Reply #3 on: October 01, 2024, 04:53:15 PM »

Thanks.
There's helikons (i.e. naturally-sized bass reeds, whether single-pair or octave-pair mounted) in Hohner Ouvertures, 234, 235, 255 models. Sounds terrific.
There's helikons in 1950s Tula factory harmonikas too, before they switched to bayan scale.
Quite typical to see them inside Steirische harmonikas and Czech Heligonkas I believe.

I've got oversized reeds (about ~15mm longer than typical accordion) in the original Morino with a 180-degree bass reed chamber and that's probably the best bass I've heard coming out of a squeezebox.
Similar reed scale but soviet factory and without 180-deg chambers in my Vostok. A bit of a harsher sound but I'd take that over any undersized bass reed every day.

Mind you, all of these boxes are noticeably larger than a pokerwork! Don't know if you'll run out of air on a smaller box.
My build is 17.5x31cm, which should be OK. I can always go smaller if it doesn't work, but it's a lot harder/impossible to go larger if you start small.

So definitely recommend fitting larger basses into a melodeon, as long as there's space inside the box.

For sourcing the reeds, dix are an option if you manage to get a reply from them. I suspect that Carini might have oversized reeds, but not necessarily helikons. Worth checking.
You can re-cycle some old bayan bass reeds (which is where I got mine), but there's a problem that high-end reeds are usually single-plate mounted. At least Russian or Polish ones. If you get a Ukrainian box, you're more likely to see pair-per-plate reeds. Or you can just cut up a single-plate with a thin hacksaw  >:E

Factory-built bayans are best avoided. Even though the reeds are on a pair-per-plate basis, the weights are riveted into the tips rather than soldered. Can be a pain to re-tune. And the factory reed quality can be abysmal.
« Last Edit: October 01, 2024, 04:56:29 PM by mChavez »
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Upside down bass reed mounting?
« Reply #4 on: October 01, 2024, 07:06:04 PM »

Harmonikas make high quality reeds.
DIX, Helikon, etc. can be found here:
https://www.harmonikas.cz/?s=nabidka&id_produkt=21
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Upside down bass reed mounting?
« Reply #5 on: October 01, 2024, 11:50:36 PM »

Yes to Harmonikas!
I got some from them a while ago, they're really works of art. Sadly, there were several confusions in our correspondence which ended up with me receiving reeds in the wrong octave! They went back, as in the octaves I wanted, the reeds would have been too big anyway. Bugger!
But absolutely beautiful.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Upside down bass reed mounting?
« Reply #6 on: October 02, 2024, 07:10:14 AM »

Tried contacting Dix/Harmonikas on 3 different occasions over the last few years and never received a single reply.
I don't think I'd ever bother wasting my time on them again to be honest - if they can't be bothered making a sale, I dread to think how they would deal with a quality control issue or a warranty claim.
I'm used to the world of musical instruments being expensive, but if we do a reality check, we're talking enough cash to buy a used car (at least a starts-drives-MOT'd one).
Their bulk sales must be doing pretty well if they don't bother with retail.
« Last Edit: October 02, 2024, 07:12:28 AM by mChavez »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Upside down bass reed mounting?
« Reply #7 on: October 02, 2024, 09:35:54 AM »

You could try https://accordions-agenziaitalia.com the person to contact there is Martina Gabrieloni.  They supply reeds made by Jurgens Ciccarelli.  Martina is his sister in law and it's much better to buy from her than direct from Jurgens.  They don't list Helicon reeds, but it's worth asking.  Carini have Helicon reeds in their catalogue.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Upside down bass reed mounting?
« Reply #8 on: October 03, 2024, 07:51:15 AM »

Theo…do they supply small numbers of reeds or just sets?

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Upside down bass reed mounting?
« Reply #9 on: October 03, 2024, 08:05:23 AM »

Rog,  you would have to ask them.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Blenchy

  • Blenchy
  • Good talker
  • **
  • Offline Offline
  • Posts: 74
  • What do you mean it's upside down?
Re: Upside down bass reed mounting?
« Reply #10 on: October 03, 2024, 09:23:55 AM »

Thank you all for the replies on where to get the reeds! Sorry if that's hijacked the thread a bit!

Don't worry it's not the pokerwork they're going into! As much as I've enjoyed modifying it. I've got an old Royal Standard with a spacious bass end which came with the remnants of a broken bass reed block so figured it'd be a great chance to experiment. I'll have to have a rummage through my boxes of unsorted reeds to see what's going on there as I haven't come across many larges ones yet so buying them new may be my only option. I'll try the various avenues everyone's suggested!

I've not been able to find the bass end I was on about yet but I'm in the middle of renovating and moving house so all my box bits are split between the shed in my parents garden and the garage at my house. So give it a month and I may stumble across it!!

Thanks again!
Logged
David Blench - Sheffield

Hohner Pokerwork and Laurel D/G, 3 Voice Galotta D/G, Old 12 bass Hohner Bb/Eb, 4 Voice "Foreign" C one row. Some concertinas and many more boxes in bits

Part of Handsworth Sword and Rumworth Morris

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Upside down bass reed mounting?
« Reply #11 on: October 03, 2024, 10:34:05 AM »

Thanks.
I've sent the drawings away for laser cutting, so a photo would be interesting, but I've finalised my design already.
Hopefully, it won't need to be re-done!
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Upside down bass reed mounting?
« Reply #12 on: March 05, 2025, 07:01:42 AM »

About a month or two away from testing my new box with upside-down helies, but here's a vintage helikon-equipped CBA with the same Idea:

Helikonbass" border="0
Logged

Blenchy

  • Blenchy
  • Good talker
  • **
  • Offline Offline
  • Posts: 74
  • What do you mean it's upside down?
Re: Upside down bass reed mounting?
« Reply #13 on: March 07, 2025, 10:56:20 AM »

That's got to be the beefiest bass block I've ever seen!!

Looking forward to hearing how your upside down helies sound! I've sadly not had chance to experiment with my previously mentioned box... So I think you'll be showing yours off long before me haha!
Logged
David Blench - Sheffield

Hohner Pokerwork and Laurel D/G, 3 Voice Galotta D/G, Old 12 bass Hohner Bb/Eb, 4 Voice "Foreign" C one row. Some concertinas and many more boxes in bits

Part of Handsworth Sword and Rumworth Morris

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Upside down bass reed mounting?
« Reply #14 on: March 07, 2025, 01:00:36 PM »

I know, right. There's enough space there to hide a tuba player inside them reedblocks!
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Upside down bass reed mounting?
« Reply #15 on: March 12, 2025, 02:45:33 PM »

Slowly, but she's taking shape.

PXL-20250311-214656828" border="0

Logged

-Y-

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 896
  • Handry 18 (G/C), Mélodie (D), Club IIb (A/D)
    • a database of nearly 500 melodeons here
Re: Upside down bass reed mounting?
« Reply #16 on: March 12, 2025, 04:09:30 PM »

Is the idea of mounting them upside down to have a better response (ie shorter transient response)? If so it's worth a try.
It would seem surprising that only flipping side would change the timbre a lot but it may improve the response. In a similar way as the chimney setting where the lower reed is mounted horizontally on top of the other reeds.

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Upside down bass reed mounting?
« Reply #17 on: March 12, 2025, 04:22:57 PM »

Quote
Is the idea of mounting them upside down to have a better response (ie shorter transient response)?

I think the answer is in the OP:

Quote
Everything is quite tight, and I'm left with ~16mm of clearance between the lowest reeds and the inside edges of the bellows. I haven't got a clue if that is enough for helikon bass or not, but it looks very tight. So I had a bright idea: what if I mounted the bass reeds upside down? This way the swinging tip is going to be below the bellows folds, and there's a few cm of clearance to the box walls.
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Upside down bass reed mounting?
« Reply #18 on: March 12, 2025, 04:29:09 PM »

In my case, and in case of pan Hlavacek photographed above, the flip is done to create some space for the helikon monsters to swing. If they were mounted downside-up, they would be hitting the bellows folds. Flipping them means that the tips are swinging well below the first fold, where the box is wider.
Three alternatives are flat fondo mounts (e.g. like Hohner 235), winkelbass ("lower reed is mounted horizontally on top of the other reeds") and a deeper box where the bass fully stacks into the trebles (e.g. Soviet 2-voice bayans where there is plenty of space for the bass block to enter the treble half).

Re timbre, a longer "chimney" sounds more pleasant, so if anything, a flip like this might make the bass sharper...However, I have no complaints against flat-fondo mounted helies, so timbre will probably be OK.

Logged

-Y-

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 896
  • Handry 18 (G/C), Mélodie (D), Club IIb (A/D)
    • a database of nearly 500 melodeons here
Re: Upside down bass reed mounting?
« Reply #19 on: March 12, 2025, 05:48:57 PM »

OK that's interesting, curious about the end result!
Besides having enough room to swing, doesn't the available air also a prime factor? These big reeds would "consume" quite a bit of air. I wonder if there isn't an ideal/minimal size of box for these reeds?
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal