Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Digital Dynamometer Question  (Read 3515 times)

0 Members and 1 Guest are viewing this topic.

fiachramp

  • Member
  • *
  • Offline Offline
  • Posts: 21
Digital Dynamometer Question
« on: October 14, 2024, 06:07:40 PM »

I'm wondering if anyone has any experience with digital Dynamometers? I recently got one and I'm looking for some advice as to the best way to use them when measuring spring tension. Is it best to take the measurement when the button begins to depress or when it is fully depressed? Also, the measurement is hard to take because the numbers jump around a lot.
Thanks
Logged

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Digital Dynamometer Question
« Reply #1 on: October 15, 2024, 12:32:32 PM »

The only measurements I've seen like this were for concertina buttons, the recommendation was for 60g of pressure to start the button movement. A concertina mechanism is very different to that found in accordions. I would suggest finding an instrument with an action you like and taking measurements from that as a starting point.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Stockaryd

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 255
Re: Digital Dynamometer Question
« Reply #2 on: October 16, 2024, 10:20:24 PM »


You can buy expensive tools, - or build something like this to measure the pressure on the buttons


https://www.concertina.net/forums/index.php?/topic/6314-spring-tension/

Logged
Hohner Corso, Hohner Erica, Emmanuel Pariselle, Gessner,   Koch,   Mariotti,    "China  NoName",   4 Toy,     -and now some more

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Digital Dynamometer Question
« Reply #3 on: October 21, 2024, 09:38:03 AM »

I suspect that this degree of accuracy is not required and may be counterproductive.

I've got a couple weights (in fact, rivet heads sets) - one at 120g and one at 90g.
Good treble key response is achieved roughly around 110g. I just eyeball and look for even, not immediate key depression under the 120g and no key movement at all under 90.
I doubt your fingers will feel a difference of ~5g between keys - you might feel it when you're testing the keyboard, but its just not something your brain is likely to pick up as nuisance when you're playing.

A lot comes down to key leverage ratio. You need springs strong enough to keep the pallets closed under bellows push pressure, but light enough so that your fingers don't need to fight them. 110g might become self-playing on fortissimo on some keyboard designs and you'll need more tension. On a melodeon, 60g spring tension is very unlikely to stand up to a forte or even mf push without self-playing, imho.
Also, the lower the tension, the higher the requirement for accurate pallet alignment.
« Last Edit: October 21, 2024, 09:43:28 AM by mChavez »
Logged

fiachramp

  • Member
  • *
  • Offline Offline
  • Posts: 21
Re: Digital Dynamometer Question
« Reply #4 on: October 21, 2024, 04:01:57 PM »

Thank you all for your responses, very informative. I have adjusted the action on boxes without the dynamometer and been happy the result. I suppose I was just trying to see if I could be more accurate in how I went about it. But I think it would be a fool's errand to try and have each button matching exactly to the gram.
Thanks again
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Digital Dynamometer Question
« Reply #5 on: October 22, 2024, 09:27:37 PM »

I use a roll of dimes (dimes stacked in a preformed coin wrapper) to gauge and adjust button spring tension.  I add or remove dimes until the button begins to sink, which then becomes my reference point for the remaining buttons or for comparing to other instruments.  I could weigh the roll of dimes on a kitchen scale if wanted an exact figure, but I've not yet had any need for that.  What I love about the roll of dimes is that I have a lot of play in adjusting the amount of weight/pressure enacted upon a button; add a dime or two and the button will sink halfway...a few more and it may bottom-out...remove one and it may rise again to three-quarters of the way down, etc. It allows you to be very precise without trying to figure out 'how hard am I pushing?'.  Works a charm...I guess it would cost you about $5 worth of dimes to get a full roll  ;D
Logged
C#/D player

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Digital Dynamometer Question
« Reply #6 on: October 23, 2024, 04:52:52 PM »

Good advice.
Dimes are a bit hard to come by in the UK though. :-X
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Digital Dynamometer Question
« Reply #7 on: October 23, 2024, 10:49:13 PM »

Good advice.
Dimes are a bit hard to come by in the UK though. :-X

I’m assuming you have an equivalent coin of some sort ; )
Logged
C#/D player

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Digital Dynamometer Question
« Reply #8 on: October 24, 2024, 08:50:26 AM »

A 1 pence coin in the United Kingdom weighs 3.56 grams and has a diameter of 20.3 millimetres.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Digital Dynamometer Question
« Reply #9 on: October 24, 2024, 10:05:55 PM »

That's nearly the same diameter as a dime but double the weight!!  You won't need as many  ;D
Logged
C#/D player

fiachramp

  • Member
  • *
  • Offline Offline
  • Posts: 21
Re: Digital Dynamometer Question
« Reply #10 on: October 26, 2024, 11:53:14 AM »

Thanks mselic. That's a great idea, must give it a try!
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal