Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Keyboard levers  (Read 3279 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Keyboard levers
« on: November 15, 2024, 03:56:40 PM »

I'm looking to rebuild a keyboard and will have to source the parts from Carini.  My questions are in relation to aluminum levers.  An example from Carini is here:

https://carinidena.it/MS5ECOMMERCE60/jsp/eco_cc_home_bs_portlet.jsp?p=dettarti&codarti=467419036

The description is: TASTI ALLUM. TRANC. CROM. 20/10 LUNGHI P19 T36 FM30

Before I reach out to Luca Carini to ask for an explanation of the measurements, I'm wondering if someone on here already knows how to 'read' this.  Another example is this:

https://carinidena.it/MS5ECOMMERCE60/jsp/eco_cc_home_bs_portlet.jsp?p=dettarti&codarti=4673161033

The above example has the various measurements illustrated, although it doesn't help much with transcribing the previous example or similar examples.

The other question I have regarding aluminum levers is the angle of the lever at the bend (usually >90 degrees).  There doesn't seem to be any mention of this in any of the listed examples and I'm wondering if they're all the same/standard?  This confuses me as I notice that on most Italian-made instruments, the levers running to an inner row of pallets (shorter lever run) tend to be at a greater angle than those reaching an outer row of pallets (longer levers).  I'm hoping those with experience ordering levers from Carini, and building keyboards, can help advise.  Thank you.
Logged
C#/D player

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Keyboard levers
« Reply #1 on: November 15, 2024, 04:04:20 PM »

Here is an example to illustrate what I'm referring to in regards to keyboard lever angles.  You can see that the levers running to the inner row of pallets angle downwards more than those that reach out further.  And I'm not referring to lateral bends in the levers, from side-to-side, which can easily be adjusted by anyone with the proper tool.
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Keyboard levers
« Reply #2 on: November 15, 2024, 04:13:37 PM »

I think the best thing for you to do is to take an example of the long lever and the short lever and photograph them on some squared paper and send the photos and other details to Luca and ask him which new parts are the best match.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: Keyboard levers
« Reply #3 on: November 15, 2024, 06:11:57 PM »

 Bear in mind also that the levers in a production instrument may not necessarily be off the shelf Carini items, but could be an action custom made for that manufacturer.

The levers that you have given the links to all have an angle of 102 degrees regardless of length, however they can be easily bent to form other angles or curves as required - for example the levers in the attached pic started as standard straight levers.

As I understand the other info:  P19 is for a lateral spacing of 19mm, the 'Bocc' is the brass bush for the axles and 6.1 is the nominal width across it in mm. (can be bent slightly to fine tune the fit widthwise). So each third lever is at a nominal 19mm centre to suit reed block and / or keyboard spacing.  Carini also sell alumimium spacers in various lengths if needed to tweak the spacing for a 2 or 2.x row instrument. ie. two levers plus a 6.1mm spacer.

The hole through the lever bush is a couple of tenths under 3mm and will need reaming to fit the axle.  F30 is the distance from the bush to a 0.8mm hole in the underside of the lever in which the end of the spring sits.  T is the distance from the bush to the piston - bear in mind that this will effectively shorten if the lever needs to be bent sideways to reach its button position. They also sell the same levers without pistons fitted so you can make them exactly the length you need. (But fitting the pistons is not entirely straightfoward)

I don't know about the 10/20 in the lever description - but this is also given for lever frames, so I guess it might indicate that the parts are suitable for keyboard angles of between ten and twenty degrees?

I hope that helps, and would be interested to hear anything else you learn about this.
Theo's plan sounds a good one to me!
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Keyboard levers
« Reply #4 on: November 15, 2024, 07:24:45 PM »

Thanks, Graham - very helpful!

How is it that you were aware of the lever angles being 102 degrees in the links I provided?  Is that the standard angle for the levers Carini supplies?

I'm well aware that the parts that were shown in my example are not necessarily stock from Carini, and that builders may make or have made for them specific parts.  I'm happy enough to make use of ready-made stock parts in this case.

You mentioned that the levers in your example started off as standard straight levers but were bent to form other angles - how? All of the aluminum levers I have seen are quite thick and solid and cannot be bent easily.  In fact, to adjust button height by even a mm or two requires 'punching-out' notches on the top or bottom of the levers with a special tool (or a home-made one in my case) in order to effectively bend the lever and lower/raise the button.  Yours look lovingly curved!  Could you please explain what you are doing?  As mentioned before, I'm not referring to bending them laterally - side to side - which is a very different story and no trouble at all.
Logged
C#/D player

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: Keyboard levers
« Reply #5 on: November 15, 2024, 09:54:27 PM »

The angles - I have some of those levers here in different lengths so simply went out and measured them ;)

As for bending them, for small adjusments to button height with the levers in situ I have a home made tool to crimp the upper or lower edge of the lever as you describe.
To shape them like the ones in the photo I would have made a plywood template to the profile I wanted.  I then simply put a piece of steel bar in the vice as a former and gently bent the levers around it by hand, comparing them against the template and tweaking until they were correct. I don't recall the exact details but it would probably have involved using hand vice / parallel jaw pliers to hold the levers without damaging them.
It would be more efficient to make some kind of bending jig if you were doing lots.
Obviously the greater the radius of the bend the neater it is, but they will bend a few degrees around quite a tight radius if necessary.
These were going to be visible so I dressed out any marks from the bending and put an engine turned type finish on them with a tiny wire cup brush in a pillar drill.

Given the cost of levers it's worth experimenting on some 2mm alu strip first!
Logged

Paul Bryan

  • Member
  • *
  • Offline Offline
  • Posts: 37
Re: Keyboard levers
« Reply #6 on: November 15, 2024, 11:17:13 PM »

hi i have used  carini treble levers   a few time i ordered  2 sets for 23 treble keyboard 467419036 p19 t36 fm30 and 467419053 p19 t53 fm30 the t number is the length of that part of the lever ie t36 and t53 is a diffrence of 17 mm ie the distance between the rows to space the leavers out you use the washers  along the length of the axel  there are different size washers to fill all the space on the axel hope this helps
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Keyboard levers
« Reply #7 on: November 16, 2024, 04:43:04 AM »

hi i have used  carini treble levers   a few time i ordered  2 sets for 23 treble keyboard 467419036 p19 t36 fm30 and 467419053 p19 t53 fm30 the t number is the length of that part of the lever ie t36 and t53 is a diffrence of 17 mm ie the distance between the rows to space the leavers out you use the washers  along the length of the axel  there are different size washers to fill all the space on the axel hope this helps

Thank you, Paul - that's incredibly helpful!  I hadn't come across that particular listing.

Graham, I've attached a photo to ask - are you really suggesting that you're able to bend these levers in the way I've illustrated? I just don't see how that's possible!
Logged
C#/D player

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: Keyboard levers
« Reply #8 on: November 16, 2024, 11:48:46 AM »

That is a big increase in angle.
It's obviously best if you can source the 'correct' lever, but if not the attached pic might help.
How many degrees do you need?

I have just had a play with a pre-distressed lever from an earlier experiment, and managed to increase the angle by an additional 14 degrees without any
problem, and only a little tidying up of the bend afterwards.
It might go a couple of degrees more with care, but that would perhaps be pushing your luck.

If you've got room for a larger radius of bend then you go can further.

Another thought - cut a new lever out of some 2mm aluminium sheet and re-use the brass bush from the old lever?
Logged

Paul Bryan

  • Member
  • *
  • Offline Offline
  • Posts: 37
Re: Keyboard levers
« Reply #9 on: November 16, 2024, 12:12:23 PM »

 dont forget the thickness of the pallet and the felt and leather will change the angle and the position of the guide holder for the levers part no 46775  will also change the angle email them with your request for options they have good english  and will respond  they also sell bending tools for the levers if you are building a melodeon you would design it around the angles created by the parts available thats what i did to build my boxes  hope this helps
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Keyboard levers
« Reply #10 on: November 16, 2024, 08:02:01 PM »

Graham - that's impressive that you managed to bend it as much as you did.  I wouldn't have thought it possible without notching or removing some material from the underside of where the bend occurs. My photo was just for illustration purposes - that's not necessarily the angle I was going for.  I just wanted to make sure we were talking about the same thing!

Paul - yes, I'm aware of what you're describing.  My post here is intended as a general inquiry about sourcing parts and, in particular, sourcing levers at the correct angles.  From what I could tell of Carini's product listings for levers, there was never any mention of the angle of the lever, while other measurements were sometimes outlined in detail.  It led me to assume that the angle of the levers might be standard, which then made me wonder how different angles were achieved.  Looking at the levers used in many Italian-made boxes, they don't look like the were bent as Graham illustrated in the photo.

Thanks both for your input!
Logged
C#/D player

Paul Bryan

  • Member
  • *
  • Offline Offline
  • Posts: 37
Re: Keyboard levers
« Reply #11 on: November 17, 2024, 12:25:06 PM »

hi yes the angle of  the lever seems to be the same and the bending to suit any box is done by the maker it seems to be a sweeping bend in diffrent directions done with bending tools sold by carini or made by tool maker to the shape required so that it can be repeated multiple times a complicated process at the best of times
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Keyboard levers
« Reply #12 on: January 04, 2025, 08:19:17 PM »

Quote
They also sell the same levers without pistons fitted so you can make them exactly the length you need. (But fitting the pistons is not entirely straightfoward)

Graham, can you expound on fitting the pistons to custom-length levers, please?  I've not yet had to install pistons on levers myself.
Logged
C#/D player

Paul Bryan

  • Member
  • *
  • Offline Offline
  • Posts: 37
Re: Keyboard levers
« Reply #13 on: January 05, 2025, 02:31:11 PM »

hi just to give you my thoughts on fitting pistons on to the carini leavers if you have a leaver to dismantle its easy by grinding off the aluminium that is mushroomed over on the piston and pull off the piston then you can see the shape to cut a new leaver and fit the piston i have done this to a row of leavers if you need to fit a new piston first drill a small hole in the piston and tap it on to the leaver that is cut down to leave a small tenon like shape once the piston is installed mushroom the end of the leaver to secure it then you can bend it to the correct angle and shape to accept the button hope this is helpfull
Logged

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: Keyboard levers
« Reply #14 on: January 05, 2025, 06:03:43 PM »

Quote
They also sell the same levers without pistons fitted so you can make them exactly the length you need. (But fitting the pistons is not entirely straightfoward)

Graham, can you expound on fitting the pistons to custom-length levers, please?  I've not yet had to install pistons on levers myself.

If you are using bought in pistons they generally have a 2mm wide by 3mm high hole through them. As Paul suggests, you need to shape the end of the lever to push snugly through the hole and protrude by just enough to peen it over to lock the piston in place.  I shape them on the milling machine simply because I have one and it's very accurate, but I'm aware of others using snips, hacksaw or press tool.  Alternatively, I've also cut a slot 2mm wide and 6mm deep in the end of the pistons and then glued them over the unshaped end of the levers with CA.  It's important to clean the lever thorughly so you are bonding to clean aluminium and not the surface oxide layer, and I primed the slot in the piston with Loctite 770 prior to bonding.  I did this with the levers in situ in the instrument.
I prefer the idea of a mechanical attachment, but equally there are professional makers who glue them on and I'm not aware of it being a source of problems.
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Keyboard levers
« Reply #15 on: January 05, 2025, 11:49:27 PM »

Thanks Paul and Graham.  Let me see if I've understood correctly:

-new pistons will have a 2x3mm hole in them.  New lever ends would need to be shaped 2x3mm in order to fit through the existing hole in the pistons.  The lever needs to protrude just enough on the other end so that it can be 'mushroomed' and fixed into place.

questions:

-how does one 'mushroom' the end of the lever?  Is this then a purely mechanical connection that is snug enough that no glue is required?

-if you go Graham's alternate route of cutting out material in the pistons, how does one go about tidily and accurately cutting a narrow slot (2x6mm)?

-Paul, you said that once the piston is secure on the lever, you can then bend it to the correct angle.  I'm assuming glue would then be required in order to keep it from getting repositioned over time as the button is played?  You wouldn't want there to be any movement between the lever and piston once it's secured in the correct position.
Logged
C#/D player

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: Keyboard levers
« Reply #16 on: January 06, 2025, 11:40:01 AM »

Thanks Paul and Graham.  Let me see if I've understood correctly:

-new pistons will have a 2x3mm hole in them.  New lever ends would need to be shaped 2x3mm in order to fit through the existing hole in the pistons.  The lever needs to protrude just enough on the other end so that it can be 'mushroomed' and fixed into place.

questions:

-how does one 'mushroom' the end of the lever?  Is this then a purely mechanical connection that is snug enough that no glue is required?

Yes. Think riveting.  I grip the lever in a vice (with aluminium jaws), push the piston on and then peen the end with a very small ball pein hammer. Very gently, it doesn't need much at all

-if you go Graham's alternate route of cutting out material in the pistons, how does one go about tidily and accurately cutting a narrow slot (2x6mm)?

I guess that depends what tools you have to hand - I use a milling machine, you could do something similar with a router table or a 2mm kerf table saw blade. You'd need to make a simple jig to hold the piston to ensure both safety and accurate repeatability.

-Paul, you said that once the piston is secure on the lever, you can then bend it to the correct angle.  I'm assuming glue would then be required in order to keep it from getting repositioned over time as the button is played?  You wouldn't want there to be any movement between the lever and piston once it's secured in the correct position.

Pistons (including those supplied ready fitted on levers by Carini) tend never to be exactly square to the lever after fitting. Just bend them gently as Paul says and if they are securely fitted they will be fine - it should be the aluminium that is bending, not the piston moving on the lever. No glue involved, it is the mechanical fixing providing the strength.
Logged

Paul Bryan

  • Member
  • *
  • Offline Offline
  • Posts: 37
Re: Keyboard levers
« Reply #17 on: January 06, 2025, 02:55:00 PM »

what i did was shape the end of the leaver to leave a 2mmx 3mm tennon like shape then drill a 2mm hole in the piston and tapped the piston on to the leaver then tap the end of the leaver with small hammer then you can bend the leaver and piston to the shape needed no need for glue as the piston fit is strong enough its the same as the carini pre made ones
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Keyboard levers
« Reply #18 on: February 10, 2025, 05:53:21 PM »

Graham and/or Paul (and/or anyone else) - can you help in the selection of springs for the treble levers? Using the following example:

Quote
F30 is the distance from the bush to a 0.8mm hole in the underside of the lever in which the end of the spring sits

the springs need to be a very specific size, at least in that the length that runs from the coil to the part that would fit in the 0.8mm hole can't be any longer than 30mm (relating to the F30 measurement in the lever)...any longer and the coil would interfere with the axle that passes through the brass bushing in the lever, and any shorter and the same bushing would fail to keep the coil 'contained' under the lever.  After having carefully scoured the Carini website, the only springs that appear to fit would be the following:

0.60 gauge: https://carinidena.it/MS5ECOMMERCE60/jsp/eco_cc_home_bs_portlet.jsp?p=dettarti&codarti=3005132

0.65 gauge: https://carinidena.it/MS5ECOMMERCE60/jsp/eco_cc_home_bs_portlet.jsp?p=dettarti&codarti=3005036

0.70 guage: https://carinidena.it/MS5ECOMMERCE60/jsp/eco_cc_home_bs_portlet.jsp?p=dettarti&codarti=3005060

The above springs are all the same size but with differing gauges (0.60 being the lightest and 0.70 being the heaviest).  There doesn't seem to be an option for this size in 0.55 gauge, although there is that option for different springs.  I would tend to go no heavier than 0.60 for most button boxes, even for a 4v instrument.  Any thoughts? Suggestions? Cautions?

Logged
C#/D player

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Keyboard levers
« Reply #19 on: February 10, 2025, 06:17:54 PM »

You can wind your own springs from any gauge you want.
Different steels will have different strength, so advertised gauge may not be relevant.

I use one of these jobbies (mine was £5 delivered, so it pays to shop around).
https://recommendedvapesupplies.co.uk/products/coil-winders-coil-building-kit?srsltid=AfmBOooY5AKsRFCShtRtrMmU-FPCNxBrpmbOul11ws07OpBHaFgNfvm2
Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal