Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Keyboard levers  (Read 3296 times)

0 Members and 1 Guest are viewing this topic.

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: Keyboard levers
« Reply #20 on: February 10, 2025, 08:01:13 PM »

I have previously used Carini springs 0.65 dia  number 3005170, 3005130 for 0.7 and 3005129 for 0.75, but I don't fully understand their nomenclature, in particular the CARxxx designation in the spec of each spring.

I would agree with mChavez and suggest winding your own.  With a little practice it's not difficult at and you can make them exactly the dimensions and tension that you need.
Logged

-Y-

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 896
  • Handry 18 (G/C), Mélodie (D), Club IIb (A/D)
    • a database of nearly 500 melodeons here
Re: Keyboard levers
« Reply #21 on: February 10, 2025, 09:54:58 PM »

I've got some technical drawings of a small device to make your own torsion springs for accordions, I'll try and scan it some time this week, if it's of some interest to anyone. It's mainly a wooden cuboid with a small rod and nails, and a wooden lever.

The above springs are all the same size but with differing gauges (0.60 being the lightest and 0.70 being the heaviest).  There doesn't seem to be an option for this size in 0.55 gauge, although there is that option for different springs.  I would tend to go no heavier than 0.60 for most button boxes, even for a 4v instrument.  Any thoughts? Suggestions? Cautions?

I think you have two ways of dealing with the tension of these springs: either with the thickness of the wire, or with the opening angle. 0.60 seems a bit light for me, I think the makers I know rather use either at least 0.65, most commonly 0.7. Even 0.75 on some occasions. Mind you the ratio lightness of action/air tightness also depends on how open you adjust them, and on the length of the lever (from the axle to the button).

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Keyboard levers
« Reply #22 on: February 11, 2025, 03:56:14 PM »

I have quite a bit of experience adjusting springs (both coil/extension springs and 'scissor-type' springs) and have even made my own/repurposed others, but haven't yet been winding my own springs.  Would be curious to see examples of people's jigs to do so.

Quote
0.60 seems a bit light for me, I think the makers I know rather use either at least 0.65, most commonly 0.7. Even 0.75 on some occasions

I don't have a set of digital calipers to measure spring gauges, so I'm not always sure what I'm using unless I have something to compare to.  However, I'm surprised that 0.6 might be considered too light considering that Hohner's heaviest spring gauge for treble buttons is 0.65 which it used on their HA114s, and those are quite stiff indeed!  Mind you, the spring design is also different than what I would be using under the Carini levers so I realize I'm not comparing like with like...
Logged
C#/D player

-Y-

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 896
  • Handry 18 (G/C), Mélodie (D), Club IIb (A/D)
    • a database of nearly 500 melodeons here
Re: Keyboard levers
« Reply #23 on: February 11, 2025, 06:00:50 PM »

It all depends on lever lengths I'm afraid, 0.65 in itself doesn't really help in predicting the air tightness and the stiffness/suppleness of action. Does the HA114 have relatively short lever length (the lentgh between the axle and the button)?

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Keyboard levers
« Reply #24 on: February 11, 2025, 07:53:06 PM »

I've been using the e-cig jig I've linked to for a while now. Cheap & cheerful, but a bit slow. Just done a treble side for my new box. Bass side still to go.

Just sit down to watch a movie in the evening and make a wee bag of springs ;)


Yes, lever ratio determines the resistance at the button and resistance at the pallet. You just need to try a few springs and see what works (which is why making your own is the way to go).
Logged

-Y-

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 896
  • Handry 18 (G/C), Mélodie (D), Club IIb (A/D)
    • a database of nearly 500 melodeons here
Re: Keyboard levers
« Reply #25 on: February 12, 2025, 10:49:31 AM »

I couldn't find the technical drawings but here are some pictures of the jig I have to wind coil springs. It's inspired by a jig made by Manu Pariselle, and it works quite well.
It's made of a wooden block (mine is 62x130x24 mm but the exact size is not relevant so long as you can grip it in your hand) where a small axle is inserted (it's a 3 mm one in the picture but I have other holes for different sizes).
And there's a small crank (mine is 62x29x7 mm but again the important thing is that you can manipulate it at your own convenience). The crank is drilled in the middle in order to insert it on the axle.
There are two small nails (the same type than those used to fix reed plates on reedblocks) : one on the base, the distance between the axle and this nail will give you the length of the spring arm ; another on the crank, on the edge : it's used to coil up the wire around the axle. The shape of this crank is adjusted so that it can span over the forming spring, if that makes sense. I don't have any piano wire at the moment but when I have some I can make a small video.
« Last Edit: February 12, 2025, 10:54:51 AM by -Y- »
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Keyboard levers
« Reply #26 on: February 12, 2025, 12:12:27 PM »

Here's a video of my spring bending jig.
If you start with a much longer end you can obviously keep winding and make an extension spring instead of a torsion spring.

https://youtu.be/6yx7PwepbBk?si=AXrfxPsVYHnI_A5f
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Keyboard levers
« Reply #27 on: February 12, 2025, 04:52:29 PM »

Thanks, everyone.  I'll make a jig to make my own springs.

Interesting notes about lever ratios, distance, etc.  I understand that the force required upon a button to open the pallet will be less the longer the lever, but as far as compression is concerned (keeping pallets from pushing upwards/open as a result of bellows pressure on the push) the lever length wouldn't make any real difference; it all comes down to the strength of the spring itself pushing against the lever to keep the pallet against the fondo, yes?
Logged
C#/D player

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Keyboard levers
« Reply #28 on: February 12, 2025, 05:30:41 PM »

I'm no Einstein, but I don't think so.

The longer the pallet linkage (distance from axle to pallet), the easier it is for the air pressure to open the pallet on the bellows push. I expect that a linkage twice as long will be twice as easy to open.
At the same time, the longer the key (distance from axle to button), the easier it is to depress the button & counteract spring tension.

Example 1:
100g at the button, linkage = 5cm, key = 5cm will be the same as 100g at the button, linkage = 10cm and key = 10cm.
100g at the button, linkage = 10cm, key = 5cm will only offer half the pallet resistance compared to 100g by 5cm by 5cm. You need 200gx10x5 to have the same pallet resistance as 100x5x5.
50g at the button, linkage = 5cm, key = 10 cm is the same as 100x5x5 or 100x10x10.

I might be wrong - please correct me if I am. I dropped physics in kindergarten to focus on other subjects.

As far as I can tell, if we simplify things a little and ignore the fact that linkages and keys can bend under pressure, taking up some of the spring energy, it makes no difference at all where on the key mechanism you apply the spring tension, and whether it is expanding, tortional or compressing type...
But the best keyboards I've played have all been compression scissor springs mounted under the keys...Perhaps, it is easier to fine-tune them compared to torsional or expanding.

In addition, you have another thing to worry about: pallet lift. You only have about 4mm button travel on stepped keyboard & 5mm travel on flat keyboard. You want about 5mm pallet lift (at the centre of the pallet, that we use as the measuring point for linkage too). The key ratio can't move too far away without messing up the pallet lift.

« Last Edit: February 12, 2025, 05:54:22 PM by mChavez »
Logged
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal