Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Failed Projects  (Read 3190 times)

0 Members and 1 Guest are viewing this topic.

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Failed Projects
« on: November 18, 2024, 08:55:30 PM »

Hopefully this doesn't get too long winded but I thought some of you might relate. I'd say my skill level for doing all box repairs and tuning at this stage would fall into the "pretty good" category but it took a lot of work and time to get here and the early work falls into the "total crap" category. I have two early 2915 Hohner projects that fall into the latter group and I'm working to remedy my sins. The one box will not seal to save my life and after installing good known bellows, I determined that, grill off and ear to the pallets, I can feel air escaping past the pallets on the push. All new felts and pallets properly aligned but I wonder if the springs are just shot? Does Carini sell these?
My second fail was re-taping bellows over old tape. This is wrong on so many levels. haha First of all it makes the bellows huge and bulky. Secondly, it didn't really do the job of sealing the leaks. I'm in the process of removing all of the old tape using a bit of warm water and blade for scraping. It's going ok but a lot of the paper that goes over the cardboard folds is coming off. Not sure if these bellows are salvageable or if it will be of without the paper skim coat?

Anyways, it's always good to hear input from the gang.
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Failed Projects
« Reply #1 on: November 18, 2024, 09:22:47 PM »

Springs aren't hard to make. I did a little video on how to.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Failed Projects
« Reply #2 on: November 18, 2024, 10:02:52 PM »

If the springs are bad enough to cause pallets to leak you would feel some of them to be softer than others.  It’s much more likely to be pallets not lying flat. How do you know that your are flat? It’s almost impossible to tell by looking.  You can make a simple tester with a  cylindrical tool that goes over one hole at a time from the inside and blow by mouth.  You will immediately hear and feel those that leak. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Failed Projects
« Reply #3 on: November 18, 2024, 10:55:39 PM »

The bellow tape is not meant to seal leaks, so you will need to check the gasket and or look on inside of the bellows ( holding them up to a light) for small holes either in the cardboard or more likely the corner leather diamonds. At least that’s my experience.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

odonovanchris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 276
    • Instagram Accordion Profile: chris0donovan
Re: Failed Projects
« Reply #4 on: November 18, 2024, 11:20:24 PM »

You can make a simple tester with a  cylindrical tool that goes over one hole at a time from the inside and blow by mouth.  You will immediately hear and feel those that leak.

Thanks Theo that's a great idea - pallet leaks can be very annoying to identify but this seems like a good trick

I've had luck identifying holes in the bellows corner leathers by shining a strong flashlight from the other side and scanning all the leathers - holes are easily seen that way.
Logged
See my accordion projects on Instagram: https://www.instagram.com/chris0donovan/

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Failed Projects
« Reply #5 on: November 19, 2024, 12:04:25 AM »

How did you attach the pallets when you put them back? I would think that if had new leather/ felt and held them flat making sure the lever drops into the slot in the pallet correctly and then while holding them in place, lifted the lever / push button to raise the lever then drop a bit of hot glue in the slot and let the lever back down while holding the pallet flat, then it should be tight. I would think that it might also be worth checking how the pallet seals with the keyboard off to make sure that the button is not hitting the keyboard / bottom of the keyboard holes, which would not allow it to seal properly. If it works better with it off then that might be the problem. Which if that is the case then hold the pallet down and readjust the button height by pushing it down and limiting its travel. Good luck!
« Last Edit: November 19, 2024, 12:08:01 AM by boxcall »
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Failed Projects
« Reply #6 on: November 19, 2024, 01:18:22 AM »

If the springs are bad enough to cause pallets to leak you would feel some of them to be softer than others.  It’s much more likely to be pallets not lying flat. How do you know that your are flat? It’s almost impossible to tell by looking.  You can make a simple tester with a  cylindrical tool that goes over one hole at a time from the inside and blow by mouth.  You will immediately hear and feel those that leak.

Good call on the test tool. Maybe a small piece of rubber hose.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Failed Projectsr
« Reply #7 on: November 19, 2024, 05:15:20 AM »

You can buy a cheap stethoscope on eBay and remove the round diaphragm and use the tube as a leak detector. Very effective tool for sniffing out those hard to find leaks e.g. pallets and where the bellows meet the casing. Also, when replacing the pallet leathers, remove the reed blocks (the sound of the reeds at this stage is just a nuisance), reposition the pallets *without* glue (though I use wax not glue…which is how Dino B and many PA pallets are held on) and test for leaks. I use an engraver tool to ream out the slots a bit. Keep testing for leaks and making adjustments until it's airtight..and only then reattach pallets. Not so much an issue on melodeons but on really old PAs the pallet arms droop a bit when the instrument is held upright and I haven"t fixed that problem…so you sort of have to find its playing position to get optimal pallet arm/pallet positioning for airtightness. I'd very much doubt it's a spring issue. If they are broken, then yes, otherwise no.
« Last Edit: November 19, 2024, 07:41:23 AM by Rog »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Failed Projects
« Reply #8 on: November 19, 2024, 07:57:33 AM »



… then drop a bit of hot glue in the slot and let the lever back down while holding the pallet flat, then it should be tight.


If you have to remove a pallet after that you are in trouble!
Much better to place the pallet, and the lever in the slot, then apply a bead of hot glue over the lever as it sits in position.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Paul Bryan

  • Member
  • *
  • Offline Offline
  • Posts: 37
Re: Failed Projects
« Reply #9 on: November 19, 2024, 10:45:37 AM »

 to check if the pallet is flat on the soundboard you can use a very thin cigarette paper to slide under the pallet if it slides in easily then there is possibly a gap i dont use hot glue on pallets i use wax so you can melt it while pressing on the middle of the pallet on both sides i use a bent piece of thick steel wire for this
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Failed Projects
« Reply #10 on: November 19, 2024, 10:53:23 AM »

I'm also a convert to hot wax for pallet fixing. Less messy, and I had no problems using the instruments in Egypt's very high temperatures.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Failed Projects
« Reply #11 on: November 19, 2024, 12:41:00 PM »



… then drop a bit of hot glue in the slot and let the lever back down while holding the pallet flat, then it should be tight.


If you have to remove a pallet after that you are in trouble!
Much better to place the pallet, and the lever in the slot, then apply a bead of hot glue over the lever as it sits in position.
First off I have learnt a lot from you over the years so I really don’t won’t to contradict your sound advice, but it isn’t a problem at all. I don’t fill the slot completely just a small dab and it comes right off for me with no loss of wood. Most of the hot glue doesn’t even get into the slot and ends up on top because of the tight fit, maybe my hot glue is slightly different than yours? You can also put the tip of the hot glue gun on the metal arm near the point of attachment for a few seconds heating it back up to loosen it if needed. I guess we all develop our own ways of doing things and I don’t plan on taking them back off for another 50yrs 😂 but I get your point.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Failed Projects
« Reply #12 on: November 19, 2024, 01:15:32 PM »

I'm also a convert to hot wax for pallet fixing. Less messy, and I had no problems using the instruments in Egypt's very high temperatures.
If hot wax was good enough for Dienst (International) it's good enough for me!
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Failed Projects
« Reply #13 on: November 19, 2024, 05:25:03 PM »

"Hot melt glue and hot wax differ in how they are applied, their uses, and their melting temperatures:

Hot melt glue is a popular choice for hobbyists and crafters, and can be used for affixing and as an alternative to resin casting. Hot wax is used for hair removal."


Courtesy of Google AI.
Logged

Paul Bryan

  • Member
  • *
  • Offline Offline
  • Posts: 37
Re: Failed Projects
« Reply #14 on: November 19, 2024, 06:46:08 PM »

 bees wax and resin with a small amount of linseed oil has been used for reeds and pallets since the accordion was first manufactured i fix pallets with wax cut in to
 a strip and melt it with a soldering iron straight in to the slot and pile it up in a dome and have never had a problem just my thoughts on pallet fixing
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Failed Projects
« Reply #15 on: November 19, 2024, 06:56:58 PM »

Yes wax is fine for fixing pallets and is used by many top makers.  I use hot melt glue for convenience.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Failed Projects
« Reply #16 on: November 20, 2024, 07:16:51 AM »

I've used hot melt too so far.

What are your collective thoughts on PVA?
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Failed Projects
« Reply #17 on: November 20, 2024, 10:11:44 AM »

PVA sticking to metal? Mmmmm.
What's your objection to using wax? The fact that it's easily reversible is surely a huge plus point?
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Failed Projects
« Reply #18 on: November 20, 2024, 11:29:05 AM »

It's possible to use pva with a with a cloth patch as you find on older Hohners, though those all seem to be pre-date the availability of pva.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Failed Projects
« Reply #19 on: November 20, 2024, 12:23:13 PM »

No objection to wax at all, apart from the fact that it becomes brittle with age. By then you'd probably be in for a pad replacement anyway, so not really an issue.
I think hot melt is easier to manage and holds quite well and almost as easy to melt for minor adjustments.

For my last rebuild I've installed all pads perfectly against the fondo to be held just by lever spring tension and then dripped some bookbinding glue (afaik, slightly more flexible pva) into the joint. No particular reason - just to make my life a bit more exciting.
So far so good but I don't know yet how it will hold up.

Old German-era Morino pads were hide cloth over joint glued with glue.
Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal