Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Filing underside of reed - too much?..  (Read 1484 times)

0 Members and 1 Guest are viewing this topic.

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Filing underside of reed - too much?..
« on: February 14, 2025, 06:04:34 PM »

Hi, I’ve been filing inside reeds up by several cents with no problems (perceivable by me) when tuning in general, but this is in the context of converting A435Hz to A440Hz. If I go with Viennese tuning, which would involve the least filing, then I’ll be tuning upwards on average around 15 cents per reed (on the right hand that is) to get from 435 to 440. Is this too much to file the underside of the reeds, and should I instead remove the reedplates and file the outside of the reeds? My concern is that by filing the underside of the reed, its shape will be altered, allowing more air to escape, therefore affecting the responsiveness… So I’m wondering if there’s a maximum amount of filing that should be done on the underside, or would this effect me negligible…
Logged
Dancing about architecture since 1997

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Filing underside of reed - too much?..
« Reply #1 on: February 14, 2025, 06:19:27 PM »

You mean the inner reeds, while waxed onto the blocks?

Personally, If it's more than a couple cents up, I remove the plate, tune just a tiny bit higher, then wax back in & scratch down if necessary.
Logged

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Filing underside of reed - too much?..
« Reply #2 on: February 14, 2025, 06:23:32 PM »

Yes, that’s correct mChavez.would that be for the same reason?..
Logged
Dancing about architecture since 1997

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Filing underside of reed - too much?..
« Reply #3 on: February 14, 2025, 06:32:12 PM »

Mainly because I'll have a lot more control over what I'm doing; i won't be butchering the valves, potentially messing up the reed gap, potentially messing up the reed shape...
For a 15c shift up, even if waxing out takes a bit longer (I'm not sure it does), I think it's worth it.
Logged

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Filing underside of reed - too much?..
« Reply #4 on: February 14, 2025, 06:45:30 PM »

Ok, good to know. The maximum I’ve probably done it this way is around 8 cents, on one of those randomly flat reeds you tend to find on Hohner factory tuned reedblocks…
Logged
Dancing about architecture since 1997

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Filing underside of reed - too much?..
« Reply #5 on: February 14, 2025, 06:56:28 PM »

If I’m tuning up from 435 to 440 I usually have to replace valves and wax do all the reeds have to come off anyway.
Filing either surface of the reed can change its shape, so checking and adjusting all reed gaps should be a normal part of the tuning process.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Filing underside of reed - too much?..
« Reply #6 on: February 14, 2025, 07:01:56 PM »

Yes, I see your point… What I mean by changing the shape, applies specifically to the underside of the reed, since this is the area around which air escapes…
Logged
Dancing about architecture since 1997

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Filing underside of reed - too much?..
« Reply #7 on: February 14, 2025, 07:19:27 PM »

Yes I understand.  Also the act of filing can cause a reed to bend, and the inevitable bending of the inside reed to lift it up so you can file it can also bend  a reed. 

But the straightforward answer to your question is it’s one of those things that is best learned by experience and careful observation. It is a good idea to check the response of any reed that you have filed or scratched.. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Filing underside of reed - too much?..
« Reply #8 on: February 14, 2025, 07:51:00 PM »

Indeed, I think I have developed some good ways to support inner reeds now to minimise the likelihood  of these problems, and I’m generally a light player so getting maximum responsiveness is especially important to me…
Logged
Dancing about architecture since 1997

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Filing underside of reed - too much?..
« Reply #9 on: February 15, 2025, 02:51:44 PM »

You can most certainly tune the inner reeds up or down by 15 cents or more without needing to remove the plates, and without causing problems.  I do this all the time (I just tuned a Pokerwork yesterday from +25 cents down to +10, and tuning the entire treble side only took about an hour). If I had to remove all the plates every time I wanted to tune by more than a few cents, I'd be out of business! (unless, of course, I'm changing the valves and wax as well)  As Theo suggests, it comes down to developing appropriate techniques which take time and practice.  If you're using good sharp tools, you only ever need a light touch.  Raising the pitch of higher reeds can require a little more attention since it's much easier for the voicing (gap) to be changed in the process of lifting the reed tongue up, and you may have to adjust it again afterwards.  On the highest of piccolo reeds, I find other ways of supporting the tongue without attempting to pull them up through their opening - they get distorted far too easily otherwise.
Logged
C#/D player

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Filing underside of reed - too much?..
« Reply #10 on: February 15, 2025, 04:53:32 PM »

Good to know… On a related note, what fraction of the reed should I file were I to tune this way? With small amounts of tuning I tend to file around the end 5mm, but when tuning by a larger amount, should I file a greater proportion of the reed?..
Logged
Dancing about architecture since 1997

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Filing underside of reed - too much?..
« Reply #11 on: February 15, 2025, 05:13:14 PM »

Good to know… On a related note, what fraction of the reed should I file were I to tune this way? With small amounts of tuning I tend to file around the end 5mm, but when tuning by a larger amount, should I file a greater proportion of the reed?..

That's another of those "Length of string" questions, it all depends.  You want to avoid making the tip of the reed too thin, but you also want to avoid straying down to the "bending zone" because that will lower the pitch.  With those provisos it once again comes down to experience. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Filing underside of reed - too much?..
« Reply #12 on: February 15, 2025, 05:16:25 PM »

That’s what I thought, but I suppose there must be some kind of rule of thumb, like the end 1/4 or perhaps as much as 1/3 before the desired effect is lost?..
Logged
Dancing about architecture since 1997

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Filing underside of reed - too much?..
« Reply #13 on: February 15, 2025, 05:35:21 PM »

That’s what I thought, but I suppose there must be some kind of rule of thumb, like the end 1/4 or perhaps as much as 1/3 before the desired effect is lost?..

It all depends of the profile of the reed.  High pitch reeds are thinnest at the tip, low pitch reeds are thinnest in the centre, so they behave differently

If you have some spare reeds that you can afford to loose there is a useful exercise that will give you more insight.  Take a reed and tune it up say 20 cents, by filing near the tip.  then tune it down by a similar amount by filing in the bending zone.  Then repeat that process testing the reed as you go and see how it eventually degrades.  Do the same thing with high pitch, mid range and low pitch reeds and you should get an appreciation of how far you can go before the reed degrades.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Filing underside of reed - too much?..
« Reply #14 on: February 15, 2025, 05:50:38 PM »

To add to what Theo is saying, there is also a lot of variation between different makes of reeds. Some reeds have very thin tips (such as Bincis) and will not have as much material to work with before becoming compromised. While the same tuning principles apply to all makes of reeds, you may have to approach some a little differently than others. Over time you will develop a better sense of how a particular reed needs to be handled. Become the ‘reed whisperer’…  ;D
Logged
C#/D player

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Filing underside of reed - too much?..
« Reply #15 on: February 15, 2025, 07:04:14 PM »

This information is really helpful, thanks!.. I’ll be extra careful not to overshoot when tuning then… Are there any particular signs that a reed has begun to degrade, such as a change in timbre? I tend to tune in very small increments, and haven’t encountered this problem as far as I know… Two brands I have tuned are Hohner and Weltmeister, so machine made, but the latter a longer scale with a softer feel…
Logged
Dancing about architecture since 1997

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Filing underside of reed - too much?..
« Reply #16 on: February 15, 2025, 07:30:04 PM »

Re thinning the tips: when it goes, it goes. I don't think there's any warning, but if it looks too thin to file, it probably is.
Either the very tip (a mm or two) becomes tinfoil-thin & snaps off, or a corner can go (if you were not filing parallel to the reed).
If you thin down a longer section of the tip, say 4-5mm, the pitch will eventually become unstable.
You can also accidentally file a very thin groove across the reed if your file is angled towards the rivet and that can snap.
I believe one of the reasons reedmakers in the olden days used tri-square files is because the triangular shape helps keep the file in parallel with the reed.

As already said, all reeds are different and some are a lot easier to work on than others.

If the tips are thin, I prefer to use sandpaper (240 grit, cut into narrow strips) instead of a file, and if it's the inner reed, you can only do it when it is waxed out. Of course, I'm not in a rush and I don't have any client deadlines to meet, so I can take my time until the job is done to my satisfaction.
« Last Edit: February 15, 2025, 07:34:18 PM by mChavez »
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Filing underside of reed - too much?..
« Reply #17 on: February 15, 2025, 07:55:18 PM »

Are there any particular signs that a reed has begun to degrade, such as a change in timbre?

My experience is that you generally have to really abuse a reed with poor or excessive tuning practices before a reed begins to 'degrade'.  I've seen a couple of Binci reeds that  - new from factory - had tips that were tinfoil-thin (which I would consider to have been a mistake/poorly-made reed) and could not be tuned any further, yet after very careful setting performed perfectly fine.  Like Theo suggested, take some junk reeds and experiment with them, see how far you can take them before you run into problems.  You'll be surprised how resilient they can be! I have regularly repuroposed PA reeds and tuned them up or down a whole tone (or more, depending on how much material you have to work with...eg. higher reeds have quite a bit of material at the base of the reed that can be removed before compromising the response of the reed).  Hohner reeds are also pretty hardy.

Re thinning the tips: when it goes, it goes. I don't think there's any warning

I might disagree with you here! I would suggest it's quite easy to see if the tip of your reed is starting to get too thin.  Just keep an eye out as you work.  There shouldn't be any surprises.

If the tips are thin, I prefer to use sandpaper (240 grit, cut into narrow strips) instead of a file, and if it's the inner reed, you can only do it when it is waxed out.

I may have to (respectfully!) disagree here, too! I generally find the only time I have to remove a reedplate from the wax to tune it is on the very highest of (usually brass-plated) piccolo reeds that I encounter on PAs.  But it's always best to use your own judgement, and if you feel that it's safer to work on an inner reed when it's been pulled from the wax, then you're probably right : )
Logged
C#/D player

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Filing underside of reed - too much?..
« Reply #18 on: February 15, 2025, 09:29:29 PM »

Yes, it does seem that Hohner reeds are very resilient… I’ve probably tuned well over 500 Hohner reeds by now, and although I have improved eg I can now consistently scrape in a straight line, I never mortally wounded a reed even on my early attempts (ok, maybe one but I swear it was already broken haha). My main tools are now a scraper fashioned from an old drill bit, and a needle file with two curved sides. To lift inner reeds I use a wooden skewer to poke them through the holes and a lollipop stick filed to a slope at the end to support them (I use a hook only on glued in blocks now eg HA114).
Logged
Dancing about architecture since 1997
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal