Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Tuning: Reeds becoming unresponsive/slow  (Read 1861 times)

0 Members and 1 Guest are viewing this topic.

Ben

  • Good talker
  • **
  • Offline Offline
  • Posts: 61
  • Hohner G/C, Pokerwork D/G, B/E, Club IIIB S C/F,
Tuning: Reeds becoming unresponsive/slow
« on: February 24, 2025, 04:57:57 AM »

Hello all,

I have done fair bit of spot tuning over the last couple years on by boxes, and even tuned my D/G from the classic hohner +20c down to a more tame +8c (approx), and the C/F down to about +12c (approx).

I just started tuning down my C/F pokerwork down to B/E, dropping each reed 1 semitone... boy this is going to take a hot second.  After tuning the low G, B, and starting tuning the C reed, I have had a lot of issues with the G and C reeds responding.  I didn't have any issues with the B reed, interestingly.  I figured I better stop and get some advice.

I am using a triangular needle file, supporting the tongue with a 0.004"/0.1mm feeler gauge under where I am scraping (~1/3 of the length up from the rivet, going across the tongue at 30-45°+-), with the feeler gauge spanning the entire width of the reed plate.  I am applying a fair bit of pressure on the file to have it cut at a reasonable speed (read: I am not 'brushing' the reed with the file, probably closer to a 'heavy' cut).  After 5-10 (?) passes*, I have been blowing the shavings off the plate, and pinging the reed. The first ping or so, it seems to just clap shut (suggesting either an alignment issue, shavings in the gap, or possibly a burr on the edge of the tongue?), but after a few more tries, it starts to ping more or less as one would expect.  However, putting it on the tuning table... nothing.  Exceedingly high pressures and it may start sounding, but the reed sounds pretty strained.  I tried bending the tip of the reed up away from the plate a couple times to increase the set. On the G reed, this improved the situation, but did not fixed it (it is still was very slow to respond).  The C reed, however, repeated attempts haven't seemed to remedy the situation, and it won't sound at all. Uh oh.  It seems to ping ok, so... not an alignment or dust issue...?

*As a point of reference with file pressure: tuning the G and B reeds down to F# and Bb took...20+- passes each with the file?

So a couple of questions:

1) I am correct in my assumption that this sounds like a reed set issue?  Or are there other issues that could be causing this? (burrs, shavings, bent reeds :-[?)
2) Have you had similar issues when tuning?
3) Am I using appropriate support under the reed?
4) Would it be better to use a dremel instead of a file to lower the pitch this much?

Any other tips/comments?


Thanks,
The Newbie Tuner (i.e. Ben)
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Tuning: Reeds becoming unresponsive/slow
« Reply #1 on: February 24, 2025, 07:24:40 AM »

1) All of the above. Could also be reed rotating on its rivet to start clipping the side, or deformed slot closing in on the reed from being "coined" by the steel feeler gauge or from accidental file slips.
Good news: most likely, it's either the reed burr that you can gently bump off with a fine file or a bent reed.
The reeds bend at the point where they start contacting the feeler, so you'll need to re-gap, ensuring good reed shape. Check the reed is not "diving" in the middle of the slot.
But if you file aggressively, when you file across the reed you apply quite a bit of rotational force on it - force the rivet is not designed to hold.
I assume reeds are valved - if they are plastic, you can shine a wee torch through the valve and see if anything's clipping.
2) Yep. Right now I'm filing a set of antique hand-made reeds down 40c and facing all of the above issues apart from slot deformation (plates are brass, so it's a lot harder to deform them). All reeds were originally tuned to either A=450 or A=430. Hard to tell.
3) I haven't thought of anything better I'm afraid.  :(
4) More of a no than a yes. The only way in which I used a dremel on reeds was on the occasions when I was making my own reeds and needed to shift the pitch down more than a semitone. A wee sanding drum insert with 80-120 grit and slow speed works OK on softer steels and soft metals, but won't help much on the really hard stuff you'd find in bayans and bandoneons.
If you are going down a semitone on each reed, this might be better than a file, but you need some practice to learn to take off material evenly across and along the reed.
Forget about grinding wheels at 20k rpm - best way to kill a reed.
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Tuning: Reeds becoming unresponsive/slow
« Reply #2 on: February 24, 2025, 07:53:00 AM »

PS A while ago there was a youtube channel by a very experienced (including working for Hohner and Scandalli I think) ukrainian fettler who gave a lesson on reed gapping in one of his videos.
The lessons are long gone, but I've reproduced some of the reed shapes from memory (gaps are exaggerated for demo purposes):

A is optimal. 2/3 of the Reed is almost in line with the slot (no more than a fag paper thickness above it). The last 1/3 gently curves up to give you your desired gap.
B & C work but can give you worse response than A. If you're really going to town to hot rod the reeds, change these to A.
D & E will probably start but will suck air. Note: reeds are not always riveted on perfectly above the plate. So this is a faulty reed.
F, G, H, I, J won't start or will have very noticeable response problems.
I is what you might get after filing the reed that's resting on a pinger. The first kink is caused by file pressing down against the pinger, while the second bend occurs when you try to gap the reed back into shape.
J is very common on "inside" reeds that have been pulled through the slot during tuning.

« Last Edit: February 24, 2025, 08:15:33 AM by mChavez »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning: Reeds becoming unresponsive/slow
« Reply #3 on: February 24, 2025, 08:23:27 AM »

Those diagrams and your descriptions are an excellent illustration .  I’ll borrow that  to use.with my students if you don’t mind.

Back to the original question.. no much to add to what MChavez has said but a couple of points. 
1) I would use something wider than a feeler gauge.  That way it’s easier to spread the filing evenly over a wider area so that changes in thickness of the reed are as smooth as possible. If you use a: softer material then there is also less risk of damaging the edge of the slot.

2). On lower pitch  reeds i usually add solder to the reed tip if i want to lower the pitch.  As  rule of thumb  I do this on reeds that have some full thickness material near the tip and maybe one or two notes higher.  This avoids making the bending part of the reed too thin which weakens the spring effect of the reed which causes it to flatten more when driven hard. For the highest pitch reeds it’s the reverse.  These are thinnest at the tip and thick in the bending zone,  so you can file to lower the pitch without detriment even by several semitones.  For example I’ve just made some piccolo reeds  for the top two buttons on a C one row. For the highest I started with a unisonoric E7 and lowered one tongue to B6 that’s 5 semitones.  It sounds fine on the test bellows,  have yet to see how it works in the instrument.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Tuning: Reeds becoming unresponsive/slow
« Reply #4 on: February 24, 2025, 10:55:59 AM »

You're welcome - glad if it helps.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning: Reeds becoming unresponsive/slow
« Reply #5 on: February 24, 2025, 11:09:36 AM »

Thanks
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Tuning: Reeds becoming unresponsive/slow
« Reply #6 on: February 24, 2025, 04:06:48 PM »

Quote
The lessons are long gone, but I've reproduced some of the reed shapes from memory (gaps are exaggerated for demo purposes)

The book 'The Ins and Outs of the Accordion' by Thierry Benetoux also has diagrams of reed shapes (12, is this a coincidence ?) along with a table relating the shapes to reed response in 4 octaves with words: perfect, good, normal, borderline, poor, too much air. Maybe it's a bit more detailed: for example the shape that is 'perfect' for low (octave 1) reeds is rated 'poor' for octave 3 and 4 reeds. Anyway, just thought this may be of interest.
Logged

odonovanchris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 276
    • Instagram Accordion Profile: chris0donovan
Re: Tuning: Reeds becoming unresponsive/slow
« Reply #7 on: February 25, 2025, 05:32:42 PM »

A is optimal. 2/3 of the Reed is almost in line with the slot (no more than a fag paper thickness above it). The last 1/3 gently curves up to give you your desired gap.

I always thought that shape A is just a residual curve left from the way the strip steel is coiled up when manufactured. It's helpful to install the tongue with curve facing up from the gap. These are very nice illustrations - thanks for sharing.
Logged
See my accordion projects on Instagram: https://www.instagram.com/chris0donovan/

Ben

  • Good talker
  • **
  • Offline Offline
  • Posts: 61
  • Hohner G/C, Pokerwork D/G, B/E, Club IIIB S C/F,
Re: Tuning: Reeds becoming unresponsive/slow
« Reply #8 on: February 25, 2025, 06:26:02 PM »

Thanks for the responses!

@mChavez, fantastic visual, Thank you! Yeah,it absolutely looks like its just a reed set issue.  The tongue certainly looks like it is below the face of the reed plate.
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Tuning: Reeds becoming unresponsive/slow
« Reply #9 on: February 26, 2025, 07:20:27 AM »

is just a residual curve left from the way the strip steel is coiled up when manufactured.

This might well be the case with modern mass-produced reeds, but if you inspect the antique stuff, back in the days when highly skilled craftsmen were coaxing each reed into the right profile by hand, it's hard to tell which side was up and which was down after all the manual cutting & filing.
In fact, if you try cutting reeds yourself with shears, you'll see that they tend to come out with a corkscrew twist and need to be trued up with pliers before fitting & profiling anyway.

Interestingly, I've got 2 sets of top-grade hand-made bayan reeds (one is pre-WW2, the other could be 60s) and in both cases they were filed from both sides, about 50/50 ??? unlike the modern reeds where the "inside" is left blued and all the filing is done from the "top".

But I digress into reed geekery.
Logged

odonovanchris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 276
    • Instagram Accordion Profile: chris0donovan
Re: Tuning: Reeds becoming unresponsive/slow
« Reply #10 on: February 26, 2025, 09:55:48 PM »

is just a residual curve left from the way the strip steel is coiled up when manufactured.

This might well be the case with modern mass-produced reeds, but if you inspect the antique stuff, back in the days when highly skilled craftsmen were coaxing each reed into the right profile by hand, it's hard to tell which side was up and which was down after all the manual cutting & filing.
In fact, if you try cutting reeds yourself with shears, you'll see that they tend to come out with a corkscrew twist and need to be trued up with pliers before fitting & profiling anyway.

Interestingly, I've got 2 sets of top-grade hand-made bayan reeds (one is pre-WW2, the other could be 60s) and in both cases they were filed from both sides, about 50/50 ??? unlike the modern reeds where the "inside" is left blued and all the filing is done from the "top".

But I digress into reed geekery.

Are those reeds mounted to long plates or individuals? I've read about 50/50 filed reeds before - the advantage is the steel stress is balanced out on each side so less residual stresses in the material. Would love to see pictures of those reeds!
Logged
See my accordion projects on Instagram: https://www.instagram.com/chris0donovan/

Ben

  • Good talker
  • **
  • Offline Offline
  • Posts: 61
  • Hohner G/C, Pokerwork D/G, B/E, Club IIIB S C/F,
Re: Tuning: Reeds becoming unresponsive/slow
« Reply #11 on: February 27, 2025, 08:48:20 PM »

Just wanted to post an update.  Finished rough tuning the concert set of C reeds down to B last night, and knowing it was the issue of the reeds being set too far down into the slot just made things soo much easier to diagnose and fix.  Superb!

As an aside... I came across a rather odd case where I was tuning a higher reed, and I was 10-15c sharp, did a couple light passes to coax it down as I had done on other reeds, and suddenly it was reading -20c flat! This happened on 2-3 different reeds.  I have no idea what happened in those cases, but it was certainly a *gasp* oh crap moment.  Any ideas why this might be the case?  I don't think I was holding the file differently or pushing harder.  Could a difference in set make that big of a difference? (I have been bending the reed up before each time getting it on the bellows to ensure it sounds w/o issue)
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning: Reeds becoming unresponsive/slow
« Reply #12 on: February 27, 2025, 10:01:51 PM »

Just the act of bending a reed usually flattens the pitch by a few cents.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Tuning: Reeds becoming unresponsive/slow
« Reply #13 on: February 28, 2025, 01:39:38 PM »

Are those reeds mounted to long plates or individuals? I've read about 50/50 filed reeds before - the advantage is the steel stress is balanced out on each side so less residual stresses in the material. Would love to see pictures of those reeds!

9 times out of 10 they come in a "solid-plank" version i.e. gang-mounted on a single plate.
Very occasionally you get "singles". In my case somebody took the single plates, hacksawed through them, then waxed them into a bayan  :o
Will be quite awkward to work with as in places there's not much brass left between the reed and the edge of the plate. But should be the sweetest sounding dry box in the world when I'm done with it.

PXL-20250228-122409904" border="0
PXL-20250228-130245303" border="0
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal