Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Keys Adjustment on Swiss made Erica  (Read 7937 times)

0 Members and 1 Guest are viewing this topic.

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Keys Adjustment on Swiss made Erica
« on: December 10, 2009, 10:47:25 PM »

So I just took delivery of what I am presuming an old swiss made Erica in G/C.  I will place pix up for those curious to see it.  The keyboard says Made in Switzerland by Accordina.  Not sure if it's just the keyboard thats made in Switzerland or the whole box.  Anyway the keys sit almost flush with the keyboard and I'm wondering how to adjust them so they sit higher. Can this be done and if so how?  Here are some pix of the box and it's keyboard.  It does play but is in need of some work, bellows are air tight and it seems to be in excellent condition for it's age.  The keyboard appears to be wood the problem is that the buttons almost sit flush and so when playing they sink below the surface of the keyboard which interferes with fingerwork.

Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

Andy in Vermont

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 948
  • Mélodie
    • Melodeon Minutes (blog)
Re: Keys Adjustment on Swiss made Erica
« Reply #1 on: December 11, 2009, 02:36:28 AM »

Very very nice find.
The button height looks great to me!
Search melodeon.net for threads that describe putting padding _under_ the buttons, within the keyboard.  I think that you'll find that if you can limit the button travel somewhat (but not too much), this is going to be a very fine box to play.

RGF

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 214
Re: Keys Adjustment on Swiss made Erica
« Reply #2 on: December 11, 2009, 03:35:40 AM »

I've had good  luck with just a wee bit of brute force! Lift the pallets until the buttons touch down, and then lift them just a bit further. The linkage, at the pivot point where it bends 'round from pallet arm to button arm, will twist a bit, and so raise the button. I've learned to do it cautiously, as raising the button too much will then require opposite adjustment. This is how I adjust the height and level the buttons.

You also need to apply the upwards force at about the pallet attachment point, not at the end of the pallet, so as to avoid snapping it loose from the end of the lever.

I'm sure others with more experience will weigh in..... I'm just a dabbler at this.

Bob
Logged

callmemario

  • HOHNER ERICA G/C
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 114
Re: Keys Adjustment on Swiss made Erica
« Reply #3 on: December 11, 2009, 03:57:31 AM »

Ugh!, sounds rather delicate to do unless one has quite a bit of experience, the whole mechanism will come apart! :-0


But it's a nice box Ajay38!!.  Can't wait to see how it turns out.

Mario


I'm sure others with more experience will weigh in..... I'm just a dabbler at this.

Bob
Logged
"Life is what happens to you while you're busy making other plans." (John Lennon)
*********************************************************************

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Re: Keys Adjustment on Swiss made Erica
« Reply #4 on: December 11, 2009, 04:13:34 AM »

Not sure about the brute force idea.  When I got my Double ray someone who had played it before, it was a demo from the Button Box in New England.  Someone had adjusted the button height by pressing down the buttons until the button arms or whatever they were called were bent to lower the button travel. I paid Michael Usui to put a new keyboard on and he had a heck of a time fixing those bend rods.  Anyway I'm hoping that I can do these things with more finesse.  But as I said I'm really not a mechanical person at all. I might just send the box to Michael and have him do the work. Expensive though but maybe well worth the investment if the box is as good as some seem to think.
Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

Andy in Vermont

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 948
  • Mélodie
    • Melodeon Minutes (blog)
Re: Keys Adjustment on Swiss made Erica
« Reply #5 on: December 11, 2009, 05:16:53 AM »

I might just send the box to Michael and have him do the work. Expensive though but maybe well worth the investment if the box is as good as some seem to think.

Ajay, I actually don't think it's worth that kind of "investment" -- it could be fun for you to learn more about how the various aspects of the button accordion work, with the bonus that in the end it will be a nice box.  But if you add up what you end up spending on various old boxes and professional repair of those boxes, I think that you'll find that you could buy one really nice "recent" box.  OR save the repair funds for special Walthers, Paolos, etc.
Just one blokes opinion, your mileage may vary...

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Keys Adjustment on Swiss made Erica
« Reply #6 on: December 11, 2009, 08:12:57 AM »

Not sure about the brute force idea. 
'Brute force' is not really the ideal term to describe this process. Gentle easing is much nearer the mark. During the construction of my Stowmarket one-row box, it was necessary to adjust the button height and travel by exactly this gentle bending process. Rees showed me how to do it and it worked just fine (thanks Rees!). I believe it is a standard practice technique, not an amateurish fix-it. As RGF has pointed out, just ensure that you push on the pallets at their attachment point with the metal arm, not on the pallet ends.

Just go carefully, a little bit at a time. You will soon gain confidence as you proceed. If you go too far it's not difficult to reverse the bending. Your overall aim should be to get all the buttons at the same height above the surface of the keyboard.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

old geezer

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 241
  • Hohner Melodeon
Re: Keys Adjustment on Swiss made Erica
« Reply #7 on: December 11, 2009, 08:26:09 AM »

Button height can be a personal preference
I myself prefer lower buttons as in your pic', the advantage of the lower buttons enable the finger to slide up or down to the next note of a tune (song) whilst anticipating several notes ahead of wot is being played

from my pic', I've made 3 tools for the purpose of adjusting the height of the button lever mechanism. 
2 of the levers were made from bicycle tyre levers, that I've modified with a small file, one being left handed and the other right.

Not sure about the brute force idea. 

I'm in agreement with Steve
Just go carefully, a little bit at a time. You will soon gain confidence as you proceed. If you go too far it's not difficult to reverse the bending. Your overall aim should be to get all the buttons at the same height above the surface of the keyboard.
Logged
Jack Murphy    beyond the black stump

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Keys Adjustment on Swiss made Erica
« Reply #8 on: December 11, 2009, 08:38:43 AM »

Before bending the pallet arms to provide the desired travel I would either pad the underneath of the keyboard with felt to stop the travel and reduce clattering or place a thin bar of wood just under the pivot of the mechanism to stop the arms moving. There is a detailed thread on button travel and some good photos from Theo of the fitting of a wood block.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Keys Adjustment on Swiss made Erica
« Reply #9 on: December 11, 2009, 08:46:19 AM »

The photos are here if you want to take a look.  That is a public kink to my facebook album.

You should check that the fingerboard is correctly fitted,  if its not sitting at the correct angle the buttons will look lower or higher than they should. A small splinter of wood under the fingerboard, or screws not tight are all it takes.  Otherwise bending the levers is the only way to adjust the button height, that is what Michael would have to do.

 I agree with previous posts that the existing low button height would be quite playable
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Re: Keys Adjustment on Swiss made Erica
« Reply #10 on: December 11, 2009, 01:36:48 PM »

I might just send the box to Michael and have him do the work. Expensive though but maybe well worth the investment if the box is as good as some seem to think.

Ajay, I actually don't think it's worth that kind of "investment" -- it could be fun for you to learn more about how the various aspects of the button accordion work, with the bonus that in the end it will be a nice box.  But if you add up what you end up spending on various old boxes and professional repair of those boxes, I think that you'll find that you could buy one really nice "recent" box.  OR save the repair funds for special Walthers, Paolos, etc.
Just one blokes opinion, your mileage may vary...
I tend to agree with you Andy as the last project was the Corso and it was a big investment.  I'm thinking that this should be my project however it's going to be a big one.  After playing it I noticed that a couple notes play only one reed rather than the two that you should hear in a two voice.  While I'm not a very patient person when it comes to precise technical work it might behoove me to learn some melodeon repair so as to save myself some money in the future.  I'm curious to find out what these things are made of anyway.  I'm going to go through Tallships diary about his old hohner's refurbish and see what I can do with this one.  I'll keep all posted as I go. 
First off does anyone know where to get round felt pads to adjust the travel in the keyboard?
Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

RGF

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 214
Re: Keys Adjustment on Swiss made Erica
« Reply #11 on: December 11, 2009, 02:30:25 PM »

OK, I give........I suppose that "brute force" wasn't the correct term, but at least I did preface that with the words "wee bit of"! (:) Steve's was the more accurate description, but we're talking about the same thing.

I've done all my Hohner keyboards in the three steps that folks here have suggested: First, as Theo mentioned, by making sure that the keyboard is properly fit. Second, by some gentle, delicate, measured, and cautious bending, always taking care to stop short of brute force (:), to get the button height to my liking. And the last is to put hard felt beneath the buttons to stop their travel when approximately flush with the top of the keyboard.

An afternoons work and it's a completely different instrument.  It requires patience and care, but it's not difficult, and even on my first try at it I didn't break anything. So I'll usually be on the side of encouraging someone to give it a go!

Bob
Logged

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Keys Adjustment on Swiss made Erica
« Reply #12 on: December 11, 2009, 02:37:23 PM »

If your taking the keyboard off have a look for air escaping around the keyboard screws. I hadn't thought that this would really cause any leaks until Theo mentioned the leather washers around the screws - and on closer on inspection, lets just say, I'm glad its a melodeon leaking air from a joint and not my plumbing (again!).
Logged

Andy in Vermont

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 948
  • Mélodie
    • Melodeon Minutes (blog)
Re: Keys Adjustment on Swiss made Erica
« Reply #13 on: December 11, 2009, 06:38:52 PM »

First off does anyone know where to get round felt pads to adjust the travel in the keyboard?
You don't need round pads, just a strip of felt.  You can easily get felt at a craft store; if there aren't any locally owned ones in your area I'm sure there is something like "Michaels" or "AC Moore" etc.
Good luck.
PS: Regarding single reeds sounding instead of two  -- open up the box and start to orient yourself to which reeds relate to which buttons.  There might be some broken reeds, but it is likely that reeds are not sounding because they are "stuck" -- sometimes all it takes is a small amount of dust or hair, and a reed won't sound until it is removed.  You can use compressed air to get rid of some of the dust or grit.

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Re: Keys Adjustment on Swiss made Erica
« Reply #14 on: December 11, 2009, 07:05:32 PM »

I haven't yet opened up the box but the keyboard is one piece so I have to figure out how to get it off etc.  I do notice a kind of smoky ripe odor that comes when I work the bellows so I'm wondering what I'm going to find when I open the thing proper.  Another question is can I use WD-40 to clean and lubricate the button arms and linkages?  This is a box that is about 40 years old so I'm pretty sure the reeds will need some kind of work. 
Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Keys Adjustment on Swiss made Erica
« Reply #15 on: December 11, 2009, 07:20:25 PM »

I haven't yet opened up the box but the keyboard is one piece so I have to figure out how to get it off etc. 
Pull out the bellows pins and look for two woodscrews that go into the neds of the fingerbiard
Quote
I do notice a kind of smoky ripe odor that comes when I work the bellows so I'm wondering what I'm going to find when I open the thing proper.  Another question is can I use WD-40 to clean and lubricate the button arms and linkages? 
Best not to.  Just brush or blow out all the dust, hair and spiders.   If you want to be thorough then release all the springs remove the retaining screws and lift out the mechanism.  Pull out the axle rod and the whole thing is in bits.  Note there are two different weights of spring.  The ones for the outside row are 0.55mm, inside row 0.5mm.  Best to keep the levers all in the same order too.   Once the rod is out clean off any rust with steel wool or fine abrasive paper and rub with a rag sprayed with WD40.
Quote
This is a box that is about 40 years old so I'm pretty sure the reeds will need some kind of work. 
Reed work takes a bit more learning.  You'll need to buy an even cheaper box to practice reed work on.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Re: Keys Adjustment on Swiss made Erica
« Reply #16 on: December 13, 2009, 03:17:23 AM »

So I'm having a devil of a time pulling out the Bellows pins.  They have what looks like washers under the bellows pins, I have tried to pull them out with pliers but they won't budge.  Should I try vice grips?  I'm afraid to damage something when I pull them out,  The washers keep me from getting a good grip on the pins.  Any ideas?

So it's ten minutes later and I managed to muscle up the bellows pins with a little prying and pulling, They were corroded and stuck,  Checked out the interior of the accordion and it's in excellent condition.  loosened up the reeds that did not play and then put the thing back together.  It plays almost perfectly now on the treble end, video to follow.  However the bass end some button travel issues, The bass keyboard is stepped and a couple of the bass buttons on the stepped side sit above the rim of the step they hit the edges of the accordion and that interferes with smooth playing sometimes even stopping them from being pressed.   I have to adjust the button level so that all the button lower edges don't catch on the step.  Another issue with the bass buttons is that they have too much movement from side to side due to the diameter of the holes for the buttons being much larger than the buttons need allowing the buttons to shake and move from side to side.  I'll take some pictures and post them and post some video also for those who are interested.  It's going to be a nice little box and I intend to start learning G/C as soon as it's ready to handle some extended play.  Next up it the Hohner pre war club II that is on it's way.

I'm told that once you know how to play G/C switching to C/F or another half step box is very simple.  Now to the factuality of that maybe some of you can enlighten me.

--Drew
« Last Edit: December 13, 2009, 05:09:33 AM by ajay38 »
Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Keys Adjustment on Swiss made Erica
« Reply #17 on: December 13, 2009, 09:58:38 AM »

I'm told that once you know how to play G/C switching to C/F or another half step box is very simple.  Now to the factuality of that maybe some of you can enlighten me.

--Drew

Maybe it's because I'm a simple D/G and C/F player but I have never given any thought to this question. In our world you learn a tune on the inside row and it comes out in G (D/G), F (C/F) or in your case C (G/C) and the same goes for the outside row. If you learn any cross rowing cleverness it will work on each box the same way with the same effect just a different key. Also I am currently doing (I use the word advisedly) A on my D/G box which will come of as G on my C/F (so not much use probably).

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Re: Keys Adjustment on Swiss made Erica
« Reply #18 on: December 13, 2009, 07:06:46 PM »

Sounds about right Lester.  I'm already playing on the C row of this little box. Just have to learn what is going on with the G row. 

Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Keys Adjustment on Swiss made Erica
« Reply #19 on: December 13, 2009, 08:36:25 PM »

When playing in G, most G/C players will use the higher octave of the G row
(buttons 5 - 10 approx).
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal