Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Typical box depth measurements  (Read 5022 times)

0 Members and 1 Guest are viewing this topic.

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Typical box depth measurements
« on: March 05, 2025, 12:36:21 PM »

Hi All.

I'm wondering if anybody can humour me with some measurements of their melodeons. In particular, the "width" of each half's frame... One picture's worth a thousand words here:
Screenshot-2025-03-05-12-31-15" border="0

Is there a "standard" for bass and treble? When does a box become too wide? I appreciate the frame width will be noticeably smaller if the treble grille is "raised" (think Handry vs Hascy).
Also, I imagine a G-C LMM will required a lot more space in the box compared to MM D-G due to the length of the reeds.

Thank you.
« Last Edit: March 05, 2025, 01:30:31 PM by mChavez »
Logged

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: Typical box depth measurements
« Reply #1 on: March 05, 2025, 03:52:00 PM »

I've just done some measuring ;)
A Mas and a 12 bass Handry both measure 80mm treble end. The Handry is 69mm for the bass end, and the Mas (18 bass) is 78mm.
For comparison an old Hohner Erika measure approx 80mm both bass and treble.

My most recently self made one is 70mm for the bass (16 bass), and 82 for the treble - 72mm for the case itself plus 10mm of raised grille.

Divided as follows:
Treble - 3mm thick fondo, with 54mm depth of casing inside, and 15 outside.
Bass -  3mm fond (approx), with 12mm depth inside and 55mm outside to accommodate the mechanism.

It's an LM instrument, and fitting the L treble reeds into 54mm casing depth to clear the first fold of the bellows was tight (but doable) - I'm giving an extra 3mm in the next one.
It uses an Italian register plate on the inside of the fondo, so setting register slides into the reed block bases would  immediately gain a little more clearance.

My experience is that unless you specify otherwise a 'standard' Italian reed set will use reedplates for the L reeds that are much the same length as the longest plates on the M set.
So for VA reeds the longest plate in a DG MM set is 49mm,  but the longest of the low voice plates in a GC LM set is only a little longer at 50.5mm
Binci are very similar, maybe a tiny fraction longer on the lowest L reeds.

For me it was a balance between allowing enough room to accommodate everything while not adding in any more weight or width than necessary.

Hope that helps.
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Typical box depth measurements
« Reply #2 on: March 05, 2025, 04:11:32 PM »

Thank you very much.

My current build is 82+10 bass (10mm bellows frames add "depth"), 80+10 treble and I think I'll need to add 10mm grille.

I've got a full-blown roller bass machine, so bass can't be any smaller (In fact I'm kicking myself for not leaving more room in the box to get the elbows in while I'm working on it. It's 55mm depth for the machine and I might have to re-think this once I have my button weight/leverage ratios confirmed.

It's an LM, with helikon-sized basses, but because it's only a 2-voice, the extra tall bass reedblock stacks into the treble space...at least in theory, while resting. I wonder how it will work out when I'm opening & closing the bellows.

Next box is planned to be 3-voice, and I can no longer stack the basses into the trebles, which got me thinking about body depth.
I was thinking of going 90+10 for the bass and, potentially, 90+10+10 on the treble, but it sounds like I might be pushing it... My bando had 100mm combined depth on each side and it was still manageable, but it's got a different feel to a melodeon.

*One can get extra folds in the bellows of course, but I don't think that makes a lot of difference compared to extending the body depth.

« Last Edit: March 05, 2025, 04:20:51 PM by mChavez »
Logged

Steve C.

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2075
  • Erica, Morse Anglo
Re: Typical box depth measurements
« Reply #3 on: March 05, 2025, 05:24:30 PM »

Not worldly:
What does a helikon--sized bass reed or reed block look like please?
--
Steve the Narrow
Logged
Located in Central North Carolina, USA; credit for picture: livingplanet.ca

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Typical box depth measurements
« Reply #4 on: March 05, 2025, 05:52:15 PM »

Depends how you define helikons.

1) Naturally-sized basses (i.e. no braze-on or as close to it as practically possible).
2) Naturally sized/oversized basses with 2 octaves mounted on a single plate. Apparently this helps the lowest octave start up, but in my experience even single-mounted helikons are a blast.

Here's my blocks (bass fundamental & Treble L & a bass reed next to a 50mm reed.

Size matters.

PXL-20250305-174506670" border="0

And here's a double-mounted helikon (not mine).


« Last Edit: March 05, 2025, 05:55:17 PM by mChavez »
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Typical box depth measurements
« Reply #5 on: March 05, 2025, 07:54:03 PM »

There are pictures and dimensions on Harmonika's site: https://www.harmonikas.cz/?s=nabidka&id_kategorie=5

Their reedplates are 98mm long.
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Typical box depth measurements
« Reply #6 on: March 05, 2025, 09:26:59 PM »

I bought some of those from Harmonikas, in the flesh (so to speak) they're stunningly beautiful, works of art!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Typical box depth measurements
« Reply #7 on: March 18, 2025, 08:46:33 AM »

How does one call this part of the melodeon anyway?
Semi-box? Box body? Frame (not to be confused with bellows frame?)
Logged

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: Typical box depth measurements
« Reply #8 on: March 18, 2025, 10:47:00 AM »


   We say "right end" and "left end" all the time. So I'm OK to add frame, to that? clear enough applied to the exterior

   No confusion with "bellows frame" either?  In the end they are all bits of 3-D geometry

    If we're talking about what's in there … it gets a bit more complicated …

   
Logged
  _       _    _      _ 

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Typical box depth measurements
« Reply #9 on: March 18, 2025, 01:16:57 PM »

Well, that's a topic for another day.
Having found no melodeon building books, I was toying with the idea of writing my own and sketching down the plans of my chassis, which is quite easy to put together. While I'm finishing my first melodeon right now, I've got a decade of guitar making experience to leverage off as far as fine woodwork is concerned.
But naming the parts inside the box does, indeed, get tricky.
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Typical box depth measurements
« Reply #10 on: March 19, 2025, 12:20:01 AM »

How does one call this part of the melodeon anyway?
Semi-box? Box body? Frame (not to be confused with bellows frame?)
I would refer to this part of the melodeon as the casework. Treble case or bass case.
I’m not sure if it’s a proper term but it makes sense to me.
« Last Edit: March 19, 2025, 12:26:49 AM by boxcall »
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Typical box depth measurements
« Reply #11 on: March 19, 2025, 08:44:35 AM »

Case makes sense.

While we're at it, what's the consensus on height, width, depth measurements? Which one's which?
A, B, C.

Screenshot-2025-03-05-12-31-15" border="0

I'd say Height is C. Some folks class "height" as feet-to-keyboard edge, but I disagree.
Then it gets tricky!

When talking about casework, depth is A, but when talking about squeezebox as a whole, B is often called "depth" too. :(
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Typical box depth measurements
« Reply #12 on: March 19, 2025, 08:51:56 AM »

C = Height
B = Depth
A = Never had to give it a name, but casework depth??

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Typical box depth measurements
« Reply #13 on: March 19, 2025, 09:49:34 AM »

How strange these descriptive differences seem!
Looking at a box as it's played (which is the orientation in which it is most commonly seen) it would be obvious that the height is from top to bottom, the width is from side to side and the depth is from front to back.
Why any other description would even be considered is a mystery to me.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Typical box depth measurements
« Reply #14 on: March 19, 2025, 09:59:20 AM »

Why any other description would even be considered is a mystery to me.

I agree...Until you pull the bass cover and look at the bass machine. Depth is now clearly to do with how deep the LHS casework is (and how much space you have for the machine mechs), while what used to be height now becomes width  >:E If the casing insides are not "wide" enough, you're not fitting 9 fundamental reed pairs for an 18-bass layout.
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Typical box depth measurements
« Reply #15 on: March 19, 2025, 05:37:25 PM »

"I agree...Until you pull the bass cover and look at the bass machine."

But then you're talking about the constituent parts, such as the bass end casing and the treble end casing, which is an entirely different matter, and which would give you the measurements about which you originally asked.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Typical box depth measurements
« Reply #16 on: March 20, 2025, 12:35:39 AM »

Case makes sense.

While we're at it, what's the consensus on height, width, depth measurements? Which one's which?
A, B, C.

Screenshot-2025-03-05-12-31-15" border="0

I'd say Height is C. Some folks class "height" as feet-to-keyboard edge, but I disagree.
Then it gets tricky!

When talking about casework, depth is A, but when talking about squeezebox as a whole, B is often called "depth" too. :(
I would think more in terms of the box standing on its feet and not in the playing position myself.
I’m thinking of it as a piece of casework ( think of a dresser standing on its feet.
So
C= width
B= depth
A = height, obviously the woodwork is separated by the the bellows height and the remaining measurement is divided by the two sides and minus height of the feet, etc.

But then if you’re thinking in terms of single boards to be cut it is slightly different
Where you have a boards length and or it’s depth ( this could be the same as its length) so either = C and or B. and it’s width = A  and it’s thickness = NA in your drawing.

The height as you said could easily be considered a depth when you separate the two sides (opening it up) and look at it like you would the depth of a drawer inside a dresser.
I’m just using woodworking terms here as a woodworker:)
« Last Edit: March 20, 2025, 12:42:32 AM by boxcall »
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Typical box depth measurements
« Reply #17 on: March 20, 2025, 07:30:35 AM »

thickness = NA in your drawing.

We're arriving at "casework wall thickness" terminology  ;)
Logged

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: Typical box depth measurements
« Reply #18 on: March 20, 2025, 09:12:55 AM »


  As this is "about" music, are we to discuss "volume"?   😈
Logged
  _       _    _      _ 

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Typical box depth measurements
« Reply #19 on: March 21, 2025, 07:23:41 AM »

There's no replacement for displacement.

Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal