Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: welding bass rods  (Read 2594 times)

0 Members and 1 Guest are viewing this topic.

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
welding bass rods
« on: May 01, 2025, 04:17:40 PM »

im looking to get someone to weld a broken bass push rod. its broken off at the point where it was originally welded....where it joins the fulcrum that lifts the bass pallet and im advised that welding is the way to go. Anyone know what type of welding specialist i need to find? its on Castagnari Benny. Probably 1990's vintage. Cant budge the buttons so it might have to be done in situ unless anyone knows how to remove 12 bass/chords buttons that seem to be very reluctant to move. Were it a hohner i could remove all the tiny pins and replace with fresh ones but alas instead of pins each rod has a tiny rivet at the end. Im guessing there's a tried and tested approach to make a permanent repair? any welding experts out there can tell me what kind of welder i need to take the job on. There seems to be loads of types to choose from.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: welding bass rods
« Reply #1 on: May 01, 2025, 04:30:34 PM »

If it’s the part I think than it will be essential to remove the mechanism before welding, otherwise you are pretty much guaranteed to set the woodwork on fire.

The part that has broken comes is made from two pieces of wire welded to form a T shape. I have some of the T wires which you would just have the bend to match the original.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: welding bass rods
« Reply #2 on: May 01, 2025, 06:52:48 PM »

if i can get all the buttons off the pushrods i should be able to get the whole mechanism out to send a pic....but theirin lies another issue! yes not good to set the thing on fire!
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: welding bass rods
« Reply #3 on: May 01, 2025, 07:42:11 PM »

Unscrew the top part of the button then with a bit of careful bending you can withdraw the pushrods.  Just take some photos so you know where each rod belongs.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Jerry in NZ

  • Member
  • *
  • Offline Offline
  • Posts: 13
Re: welding bass rods
« Reply #4 on: May 01, 2025, 09:59:48 PM »

Probably the best bet is to take the bits to a friendly spectacle frame repairer with a laser welder. Small-section component welds are routine work for them. I have TIG welded some pretty skinny stuff, but, at my skill level, I'd rather pay a little for laser welding.
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: welding bass rods
« Reply #5 on: May 01, 2025, 10:34:40 PM »

Got a photo?
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: welding bass rods
« Reply #6 on: May 01, 2025, 11:04:18 PM »

yes i'll try to send a pic tomorrow.....thanks to theos advice i did manage to unscrew the buttons after a lot of effort but good to know they would release with screwing rather than pulling.After that the whole mechanism came out fairly easy after unhooking springs and removing retaining screws. i failed to realise that the 12 springs arent all identical. 6 of them have a steeper angle of bend so it going to be trial and error working out which ones go where unless anyone has tips? im guessing 6 need to have more tension and 6 have less hence the angle of bend variance. good tip re spectacle guys and laser welding. its fairly clear now where the rod needs to sit before welding so if i can find the right craftman it should be do- able. I'd rather get someone who had done this kind of weld before rather than chancing my arm trying it myself.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: welding bass rods
« Reply #7 on: May 03, 2025, 06:26:58 AM »

If it was me I would probably also investigate using silver solder, but given it's not been mentioned here maybe it wouldn't work? You can buy silver solder and flux on eBay and a small gas torch (e.g. a kitchen gas torch) is ideal as it has a small flame. It takes a bit of practice but isbn't too difficult once you've read up, watched some YT instructionals and had a go on scrap metal.

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: welding bass rods
« Reply #8 on: May 03, 2025, 10:50:49 AM »

i did wonder about silver solder too. But unsure if its strong enough. i have a friend who retired from the spectacle trade 20 years ago and he helped me silver solder a pallet arm on an old international box. It worked but the arm was made of brass so maybe not the best solution for a steel rod? Be good to know if its laser welding that the folks use who do it everday over in Italy? Anybody know? Makes sense to use the tried and tested method if i can find out what the tried and tested is.
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: welding bass rods
« Reply #9 on: May 03, 2025, 10:56:20 AM »

pic 1
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: welding bass rods
« Reply #10 on: May 03, 2025, 10:58:04 AM »

pic 2
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: welding bass rods
« Reply #11 on: May 03, 2025, 10:58:41 AM »

pic 3
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: welding bass rods
« Reply #12 on: May 03, 2025, 10:59:14 AM »

pic 4
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: welding bass rods
« Reply #13 on: May 03, 2025, 10:59:56 AM »

pic 5
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: welding bass rods
« Reply #14 on: May 03, 2025, 11:05:39 AM »

hopefully pics show ok. the springs picture shows 6 that match. then 5 that match and a sixth that doesnt match the other 5. i can only assume that at some point in its life one spring was replaced without the extra bend to match the other 5. Maybe this was why the arm broke apart..... a theory? i'm guessing 6 matching springs go on the longer arms and 6 matching springs go on the shorter arms to equalise tension.
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: welding bass rods
« Reply #15 on: May 03, 2025, 11:09:08 AM »

If it’s the part I think than it will be essential to remove the mechanism before welding, otherwise you are pretty much guaranteed to set the woodwork on fire.

The part that has broken comes is made from two pieces of wire welded to form a T shape. I have some of the T wires which you would just have the bend to match the original.

thanks theo.....that might work. but i'd have to free the plastic barrel that the button screws into and it seems to not want to move. Also the arm has a pivot point in it. Good to know though if welding proves impossible.
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: welding bass rods
« Reply #16 on: May 03, 2025, 11:27:40 AM »

Ah, now I see what's happened here.
Silver solder should be OK I'd think.

I've been looking at an identical comb just a few days ago wondering how I can add a level to the rod that holds the pallet. I wonder if a brass rod flattened  just after the bend enough to take 2 rivets is the easiest option here.

Logged

Jerry in NZ

  • Member
  • *
  • Offline Offline
  • Posts: 13
Re: welding bass rods
« Reply #17 on: May 03, 2025, 11:46:14 AM »

To add a bit more background info., and dredging fading memories... I think the process originally used to fabricate the broken component is known as 'flash welding'. A welding current source is connected across the two bits, which are then forced together. The electrical resistance at the junction causes the adjacent bits to heat up and fuse together, usually with a bit of fireworks. The current flow is brief. It all happens pretty quickly. I don't remember whether it's a DC or AC process. Similar to spot welding, it's potentially DIY-able, but the amount of experimentation necessary would probably mean a visit to the spectacle repairer was far cheaper, quicker and easier...

Silver soldering would probably be OK, if the bulk of a desirable solder fillet can be accommodated. I don't think it would be strong enough without building up a reasonable fillet. On a job shaped like this, I don't think it would be easy to build up much of a fillet because silver solders are very fluid when molten. The component may have been plated: this might cause problems. Also, the two bits would have to be held by a jig whilst heat were applied. The spectacle repairer's laser is so localised that the workpiece can be safely held in the hands. Given a suitable jig, and a machine capable of low currents, you could consider TIG brazing (in which the substrate isn't melted), which would be less disaster-prone than TIG welding (where the substrate is melted - and then drops off in a molten glob...). Another possibility might be PUK welding (excuse me if I've got the acronym wrong) which some jewellers may have.
« Last Edit: May 03, 2025, 11:52:41 AM by Jerry in NZ »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: welding bass rods
« Reply #18 on: May 03, 2025, 12:33:48 PM »

If it’s the part I think than it will be essential to remove the mechanism before welding, otherwise you are pretty much guaranteed to set the woodwork on fire.

The part that has broken comes is made from two pieces of wire welded to form a T shape. I have some of the T wires which you would just have the bend to match the original.

thanks theo.....that might work. but i'd have to free the plastic barrel that the button screws into and it seems to not want to move. Also the arm has a pivot point in it. Good to know though if welding proves impossible.

To release the plastic barrel you would have to unfold the folded wire the goes right round it, and then bend the new wire into a similar fold and clench it round the plastic bit.  That all looks much more doable to me than to try rewelding a broken weld.

This is the replacement part:

Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: welding bass rods
« Reply #19 on: May 03, 2025, 12:39:03 PM »

Or you can do what all the cool kids do and just make your own parts. This joint will still be intact long after you're dead.
Prototyped in about 10 minutes from some scrap.
2.2mm for the pallet arm, 2.0mm for the lever.

PXL-20250503-113426157" border="0


By the way, thank you, you've just solved one of my sticking point for my next build  ;)
« Last Edit: May 03, 2025, 05:03:34 PM by mChavez »
Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal