Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: welding bass rods  (Read 2598 times)

0 Members and 1 Guest are viewing this topic.

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: welding bass rods
« Reply #20 on: May 03, 2025, 12:44:15 PM »

Ah, now I see what's happened here.
Silver solder should be OK I'd think.

I've been looking at an identical comb just a few days ago wondering how I can add a level to the rod that holds the pallet. I wonder if a brass rod flattened  just after the bend enough to take 2 rivets is the easiest option here.

ideally im looking to just weld it back in place as then i'll keep all the right geometry and lengths of rod so then everything lines up and bass button sits where it used to and lines up with the others. not sure i have enough room for rivets.
Logged

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: welding bass rods
« Reply #21 on: May 03, 2025, 06:10:06 PM »

Silver solder would be neat and more than strong enough. Don’t be put off by the name, it’s not like electrical solder - it’s a higher temperature brazing process.
However, if Theo is offering you a replacement ‘T’ lever to shape and fit then that is the way to go.
Logged

pete /acorn

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 930
  • .Cast Trilly
    • Acorn Instruments
Re: welding bass rods
« Reply #22 on: May 15, 2025, 10:28:34 PM »

Spare part posted
Logged
Acorn Instruments are specialist retailers of Castagnari Instruments,and have an extensive stock of new instruments on the shelf for prompt delivery in standard layouts however these can easily be changed to customers special requirements,we have over 600 reeds in stock
 We also have the largest stock in the UK of  pre loved melodons all fully serviced,and with 12 months warranty
UK and international customers catered for
www.acorninstruments.co.uk

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Re: welding bass rods
« Reply #23 on: May 16, 2025, 12:34:07 PM »

This is good.
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: welding bass rods
« Reply #24 on: May 17, 2025, 12:13:24 PM »

This is good.

thats a serious bit of kit!
Logged

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Re: welding bass rods
« Reply #25 on: May 17, 2025, 02:37:29 PM »

Logged

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: welding bass rods
« Reply #27 on: May 17, 2025, 08:46:47 PM »

This is good.

thats a serious bit of kit!

so do you know the best way to weld...i got about 6 or more answers but alas never found out what method the pros in italy use? be nice to know
Logged

Jerry in NZ

  • Member
  • *
  • Offline Offline
  • Posts: 13
Re: welding bass rods
« Reply #28 on: May 18, 2025, 01:19:13 AM »

... but alas never found out what method the pros in italy use? be nice to know

I'd expect an Italian pro doing a repair would just get a new blank from Carini and fashion it as required. Original manufacture would be by a variant of flash welding, as I've suggested.

Repeating myself again - silver soldered butt joints in this application would be weak, because the cross-section of the joint is so small. A substantial fillet would be required. Also, the wire is likely to have been heat-treated, and the silver soldering would soften the wire over a considerable distance from the join. Not recommended.

For a welded repair, laser welding, used by spectacle frame repairers, and therefore readily available, or PUK welding, used in the jewellery manufacturing trade, would be the best repair methods, I think. However, starting with a new blank has to be best...

Rivetted construction, as shown earlier, can be improved considerably by sweating the joint with soft solder, which is strong in shear. There's always a risk of rivets loosening slightly, not to the point of failure, but just allowing a little free movement. And, once it starts moving, it gets worse...
Logged

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Re: welding bass rods
« Reply #29 on: May 18, 2025, 05:49:58 AM »

This is good.

thats a serious bit of kit!

so do you know the best way to weld...i got about 6 or more answers but alas never found out what method the pros in italy use? be nice to know

I don't know the English word for this welding, maybe (butt welding) I have a similar welding machine (picture)
Logged

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Re: welding bass rods
« Reply #30 on: May 18, 2025, 05:54:29 AM »

This has been used to weld band saw blades, it has been modified to weld wires
Logged

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Re: welding bass rods
« Reply #31 on: May 18, 2025, 06:05:23 AM »

The Italians use the same method, maybe newer machines, but the system is the same.
Logged

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Re: welding bass rods
« Reply #32 on: May 18, 2025, 06:11:47 AM »

Here,,
Logged
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal