Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Hohner Erika keyboard issue  (Read 980 times)

0 Members and 1 Guest are viewing this topic.

Gabriele Rossi

  • New Starter
  • Offline Offline
  • Posts: 3
Hohner Erika keyboard issue
« on: May 06, 2025, 02:31:46 PM »

Hi,

I have recently bought my first melodeon, a Hohner Erika (with a "k") in C/F and I am in the process of making it playable again. It isn't overall in bad shape, I replaced two broken reeds, and I am in the process of revalving and tuning.

However, I think there is an issue with the keyboard, although I'm notnsure what a melodeon keyboard should be like, as I have more experience with the anglo concertina. As you can see, the buttons protrude progressively more as you move away from the grill, with the travel getting correspondingly longer. This makes the F row and the accidentals quite hard to play.

As far as I can tell, the keyboard itself seems to fit well against the casework and is at the correct angle. The button heights are slightly irregular, but I can't see any evidence of major bending in the action.

One thing which might make a difference is that the facing on the pallets seems to be quite thin, as there isn't any felt, just leather, but unless it is meant to be over 3mm thick, it isn't enough to solve the issue.

I was watching the excellent "Hot Rod Your Hohner", and he mentions reducing the travel, bu the construction of a Pokerwork seems to be a bit different in this area.

Does anyone have any ideas on this?

Thanks in advance
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: Hohner Erika keyboard issue
« Reply #1 on: May 06, 2025, 04:33:10 PM »

Looks like a keyboard alignment issue making the C row buttons higher than the F row. There are screws inside holding the keyboard. Remove these screws. If there once were shims where the keyboard meets the Fondo and they are no longer present or have moved this can be the result. Either way shims should fix it by alterating the angle of alignment to get all buttons protruding at an even height. Once thats achieved its a matter of adjusting button height to personal taste. Renewing the pallet facing either with leather (as originally faced) or felt and leather (for a less clacky result) will then alter button height but should alter it pretty evenly. Its also possible that someone has renewed the pallet facing on one row but not the other but thats extremely unlikey.  (unless they did one row and then got bored or lost the will to finish the job, or ran out of pallet facing and sold the melodeon and bought a banjo.) My money is on the shims though. Ive seen shims made of wood and also cardboard. Both seem to work once the keyboard is screwed back down again.
Logged

Gabriele Rossi

  • New Starter
  • Offline Offline
  • Posts: 3
Re: Hohner Erika keyboard issue
« Reply #2 on: May 07, 2025, 12:06:00 AM »

There definitely weren't any shims when I took off the keyboard to glue it back together.

I don't know about other Hohners, but on mine the two screws go through the soundboard and then through a small wooden block which was originally glued in the two lower corners, as you can see in the photos. The keyboard also has steps in the sides cut at an angle that sit around the sides of the casework. This all makes it rather solid, even with the large screws loosened it doesn't really move much up or down, and I'm worried about forcing it or the screws.

Also, at the moment, the four accidental buttons in tthe third row are quite low, and when I tried pushing the keyboard up a bit to see what effect the shims wpuld have, these buttons ended up only just proud of the surface, while the C row still stuck out significantly more.

Maybe the action just got bent somehow? When I bought it the bottom of the keyboard and both sides had more or less parted company with each other, and I don't think would have provided much protection in case it was bumped or improperly stored.
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Hohner Erika keyboard issue
« Reply #3 on: May 07, 2025, 01:12:37 AM »

Quote
Maybe the action just got bent somehow? When I bought it the bottom of the keyboard and both sides had more or less parted company with each other, and I don't think would have provided much protection in case it was bumped or improperly stored.

Yes, absolutely. The key levers have been pushed forward and they have twisted as a result. It can be seen at their base near the axle on the 1st, 2nd and 4th lever (3rd maybe ok ?). The flat sides of the levers should be perpendicular to the axle , or parallel to the ends of the box for all their length, if that makes sense. It should not be too hard to fix with pliers and a bit of patience. Once they're back in their normal geometry you will be able to see if the buttons really need adjustment. 
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Hohner Erika keyboard issue
« Reply #4 on: May 07, 2025, 01:35:03 AM »

I agree with tirpous you need to untwist the metal arm so that the metal is inline with the metal arm that holds the pallet. Then you should be able to hold down the metal arm that holds the pallet ( pressing it tight to the fondo and then push the button side of the metal levers down to lower the action.
I’m not sure if these metal arms with the circular bend in them will bend in by pushing on the button or if you need to push on them closer to the pivot point ( just before the circular bend)? You shouldn’t need to adjust the keyboard itself I don’t believe.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner Erika keyboard issue
« Reply #5 on: May 07, 2025, 09:06:14 AM »

I’ve worked on many examples of this model, some that have evidently never been opened since they left the factory, and I’ve never seen shims under the keyboard,  so what you have appears to be a normal keyboard setup.  Sometimes the blocks, that support the keyboard and that the screws pass through, can move, so check they are secure and located right in the corner of the case.  Also check the top surface of the blocks, they can get damaged by over tightening of the screws.

Another possible cause for low buttons is bending of the little legs that the main key mechanism is supported by.  Also check that the screws that hold the mechanism are in the original holes.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: Hohner Erika keyboard issue
« Reply #6 on: May 07, 2025, 09:35:59 AM »


"There definitely weren't any shims when I took off the keyboard to glue it back together.

I don't know about other Hohners, but on mine the two screws go through the soundboard and then through a small wooden block which was originally glued in the two lower corners, as you can see in the photos."

when you say to glue it back together do you mean the small wooden blocks were loose and reglued? if so is it possible they are glued in upside down? hard to tell from one pic. another wild guess. maybe post more pics.

[/quote]
Logged

Gabriele Rossi

  • New Starter
  • Offline Offline
  • Posts: 3
Re: Hohner Erika keyboard issue
« Reply #7 on: May 07, 2025, 10:17:29 AM »

[quote author=chris hall link=topic=31434.msg364056#msg364056

when you say to glue it back together do you mean the small wooden blocks were loose and reglued? if so is it possible they are glued in upside down? hard to tell from one pic. another wild guess. maybe post more pics.

[/quote]

I’ve worked on many examples of this model, some that have evidently never been opened since they left the factory, and I’ve never seen shims under the keyboard,  so what you have appears to be a normal keyboard setup.  Sometimes the blocks, that support the keyboard and that the screws pass through, can move, so check they are secure and located right in the corner of the case.  Also check the top surface of the blocks, they can get damaged by over tightening of the screws.

Another possible cause for low buttons is bending of the little legs that the main key mechanism is supported by.  Also check that the screws that hold the mechanism are in the original holes.

This is reassuring as regards the keyboard setup. It didn't seem to me that it was meant to have shims, but as a total novice I couldn't be sure.

As regards the blocks, they were both loose when I took the keyboard off the first time, but I'm pretty sure I glued them back on in the right orientation because I could see the old glue residue.

The photo I posted might give a false impression of how bent the levers are, they aren't as twisted as they seem, I think the quality of the photo and the fact the levers widen slightly close to the pivot gives that impression. However, I tried a bit of gentle bending on a couple of keys, and it doesn't take much to make a big difference, so maybe that is the way to go.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal