Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Problems with basses/air button on Cairdin Mini  (Read 737 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Problems with basses/air button on Cairdin Mini
« on: May 20, 2025, 05:14:00 AM »

I recently picked up a used Cairdin Mini Deluxe which is a lovely box but has some serious design flaws.  The most obvious of these is that when both the chord and bass buttons are played together at the same time, the reed tongues strike one another due to the inward-facing reedblocks being too close together.  Unlike most Cairdin Minis, this one came with a set of low basses along with a stop to take them out.  I have a suspicion that the builder did not modify his usual bass reed block setup/arrangement to allow for the swing of these lower bass reeds.  How a builder can charge top dollar for handmade instruments and send them out like this I can't quite understand...

I'm looking for a solution to this without building new reedblocks.  I see a few options:

-since the foot of the bass reedblock is quite thick, I could potentially shave off the bottom at a bit of an angle (on a table saw) to further angle the reedblocks away from one another.  I wouldn't want to go too much so as to avoid having the reed tongues on the opposite side of the block strike the bellows.

-shift one (or both) of the reedblocks a little further away from each other simply by trimming back the small pieces of wood that are glued to the fondo as guides/stops on either side of the blocks.  I've checked and the holes in the fondo/block would still line up OK given that the alignment already isn't perfect.

Any other suggestions? See photos.
« Last Edit: May 20, 2025, 05:29:42 AM by mselic »
Logged
C#/D player

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Problems with basses/air button on Cairdin Mini
« Reply #1 on: May 20, 2025, 05:28:39 AM »

The NEXT problem that I'm dealing with is the volume of the basses dropping nearly to zero as soon as I use the air button. The basses play just fine, but as soon as the air button is used - even just a *little* - the basses themselves are essentially getting little to no air and they will barely sound at all.  The air button hole is actually quite large on this instrument - bigger than those on 3 or 4v instruments which are considerably large than this compact, 2v box.  As a stop-gap measure, I put a piece of masking tape across 3/4 of the air button hole on the inside and it made a noticeable difference - the basses would sound more audibly when using the air button, but they quickly start losing volume again if the air button is pushed in a little further.  In contrast, my 3v boxes have to have the wedge-style air button pushed way down into the hole before I start noticing any impact on bass volume.  The amount of pallet lift is not unusual in the case of the Cairdin, so I'm assuming it's just the larger hole itself that is the issue.  I've attached a link to a video to demonstrate the problem (prior to taping off 3/4 of the hole). 

Once again, I'm left wondering how a builder that's been around for decades can design and market an instrument with such obvious issues..  The design of the air button mechanism itself was also dreadful, but I've remedied that with a replacement mechanism (which is not related to the problem of the basses getting starved of air - that issue is the same regardless of the metal linkage used to lift the pallet itself).

Video of basses with and without air button (note that the air button is only lightly depressed when it's being used):

https://youtu.be/QX9AN9WTqoA
« Last Edit: May 20, 2025, 05:34:19 AM by mselic »
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Problems with basses/air button on Cairdin Mini
« Reply #2 on: May 20, 2025, 08:34:46 AM »

You might solve both problems by replacing the low bass reeds with a smaller reeds and octave higher.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Problems with basses/air button on Cairdin Mini
« Reply #3 on: May 20, 2025, 01:53:00 PM »

I’d like to keep the low bass reeds…
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Problems with basses/air button on Cairdin Mini
« Reply #4 on: May 20, 2025, 02:19:40 PM »

Another idea might be to shift the blocks slightly end to end in opposite directions so that the active reed is opposite the non- playing reed.  There might be some movement this way by small modifications to the ends of the blocks,  or if that isn’t possible then detach the blocks from the sole and re-glue is shifted positions. That is likely to preserve a better alignment of the air passages.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

JNM SY

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 227
Re: Problems with basses/air button on Cairdin Mini
« Reply #5 on: May 20, 2025, 03:05:07 PM »

  It might be possible to remove a wedge out of the next reedblock to the low basses - reedblocks aren't usually at 90 degrees to the foot,they taper towards the top.
  This might affect how they sound but would give the bass reeds more room. Whip the reeds off and run the block over a  bench saw at an angle - even a few mm would make a difference.
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Problems with basses/air button on Cairdin Mini
« Reply #6 on: May 20, 2025, 04:21:55 PM »

Another idea might be to shift the blocks slightly end to end in opposite directions so that the active reed is opposite the non- playing reed.  There might be some movement this way by small modifications to the ends of the blocks.

This did the trick, Theo, thanks!
Logged
C#/D player

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Problems with basses/air button on Cairdin Mini
« Reply #7 on: May 20, 2025, 07:02:59 PM »

"even a few mm would make a difference."

I've done this a couple of times, but you must be careful to leave enough space to allow for the reed swinging inwards! Obviously this warning is for anyone with a similar problem in the future, seeing as mselic's problem is cured!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Problems with basses/air button on Cairdin Mini
« Reply #8 on: May 21, 2025, 05:26:16 AM »

After a fair amount of work, I’ve managed to sort out all of the issues I’d mentioned. Shifting the reedblocks end-to-end as Theo suggested took care of the reed tongues hitting each other. The air valve hole was greatly reduced which allowed the air valve and basses to be used simultaneously when needed without issue. I also built an entire new bass plate (with feet that actually cleared the bass strap) to accommodate my new air valve mechanism which converted a push-in button type to a more comfortable wedge-type which I prefer.

Here’s a photo of just how much the air valve opening needed to be reduced. The original hole was far too large for the instrument.
Logged
C#/D player
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal