Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Tremolo increases/decreases and disappears with varying bellows pressure  (Read 1367 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683

I’ve made the mistake of taking on the restoration of an old 1920s-era Hohner with zinc-plated, “O” stamped reeds, and it’s been nothing but grief. I’m nearing completion but the issue that I’ve discovered on a few notes is a tremolo which will vary enormously depending on bellows pressure: at +10 cents apart, the reeds will begin beating normally but with increased bellows pressure the beating will drop and, with enough pressure, will actually lock together in unison. The pitch of each of the reeds themselves remains fairly constant, even with changing bellows pressure, when they are isolated, so it’s not the reeds themselves that are the issue. The two holes in the bottom of the reedblock are actually one, but separating them with a divider (a small piece of wood glued in place to make two separate holes again) has not helped (this has occasionally helped with phase-locking in the past). Any suggestions? Blocks are braced together with several braces.

Sound clip:

https://www.dropbox.com/scl/fi/v23lzxl5a3h1imh0epeu9/varying-tremolo.m4a?rlkey=67t4inhjh9hsfj23pjmw8ti62&st=ec7y831o&dl=0
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place

I’ve seen this caused by air leaks between reed chambers in the upper part of the chamber as a result of drying cracks in the wood itself or failed glue joints.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes

Try tightening the rivet on the offending reeds. I show before and after video on one of my YouTube videos solving your exact problem (pressure dependent tremolo) but I can't remember which one. The video below at least shows the 'accordion anvil' I use for tightening rivets:

https://youtu.be/I0DncpREm-g?si=RVexBg3Ay8_KJs3c

Scott
Logged
too many boxes...please buy one, or two, or

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683

There are no air leaks between chambers, other than the obvious fact that air is shared between chambers due to the shared hole in the bottom of the block (as well as the fondo).

Tightening the rivets as Scott suggested helped to reduce the problem with the blocks on a tuning bellows, but once back in the instrument, the problem remained the same. I once again tried dividing the shared air hole in the bottom of the blocks with a piece of wood, but it made no difference.
Logged
C#/D player

odonovanchris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 276
    • Instagram Accordion Profile: chris0donovan

There are no air leaks between chambers, other than the obvious fact that air is shared between chambers due to the shared hole in the bottom of the block (as well as the fondo).

Tightening the rivets as Scott suggested helped to reduce the problem with the blocks on a tuning bellows, but once back in the instrument, the problem remained the same. I once again tried dividing the shared air hole in the bottom of the blocks with a piece of wood, but it made no difference.

Hi Matt. Try gluing the valves further up, but not so far as to affect tone/response. That solved the issue for me in the past. I've found the thinness of some zinc DIX reed plates to cause the valve pitch problem.
Logged
See my accordion projects on Instagram: https://www.instagram.com/chris0donovan/

Rog

  • Hero Member
  • *****
  • Online Online
  • Posts: 2525
  • Repair and tuning in Hants

Hmmm. I feel your pain. A few things I'd try...play around with the gaps. Close one up and get the other reed to sound, then gradually open the gap. Occasionally this seems to jolt them into behaving. Or..turn the plates over, or switch them on the reed block sides, or take them off, replace the valves (again) and put them back on with new wax. Work a feeler gauge down to the rivet to ensure there is nothing in there. If the problem persists I'd just replace the reed with one from my many boxes of reeds (which you also probably have). Normally the bracing across blocks works, so try repositioning that.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683

Chris and Rog, I've already tried all of the above with no luck.  Even changing reeds didn't help.  At this point I've spent an inordinate amount of time working on this box and trying to solve this issue (and only charging for some of those hours), and I have to walk away...I've already told the client that I'm unable to resolve the problem and will finish up the restoration of the box as-is.  I hate to admit defeat but I'm not making any headway and I can't afford to keep working away at it.

Given the kind of grief I've run into in the past with vintage (pre-1930s) boxes, I've decided that I won't work on them anymore.  There are just too many unpleasant surprises that can pop up with these vintage boxes that derail what would otherwise be a straightforward overhaul.  These "O" (or square) stamped reedplates, while having a lovely, bright tone, also have a tendency to be quite finnicky and problematic.  I wouldn't mind not dealing with them ever again.
Logged
C#/D player

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622

I associate O-reeds with boxes from Saxony, often not the best quality, but even Hohner may have used them at some stage. Sometimes their stability improves by giving them a healthy whack on the rivet.
Logged

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall


Sometimes their stability improves by giving them a healthy whack on the rivet.

   "As the actress said, to the bishop" 😂
Logged
  _       _    _      _ 

odonovanchris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 276
    • Instagram Accordion Profile: chris0donovan

The only other thing I can think of is the depth of the chamber might be too shallow. I've noticed on the reeds from Klingenthal that the tongue material is softer which gives a larger "swing" when played. Try chiseling out some of the chamber near the tip and it might help. When a reed vibrates near a flat surface the air column in between compresses and creates a cushioning effect - this acts to slow the reed down thus lowering the pitch. Sounds like what could be happening here.
Logged
See my accordion projects on Instagram: https://www.instagram.com/chris0donovan/

Dick Rees

  • Neo-Luddite
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1640

I wonder if it's the reed pairs interacting and tending towards synchronicity.  The mention of rivet tightening would seem to indicate a possible variability in or tendency for pitch shift.  That combined with waxing the platess and other factors such as gap and space in the blocks would seem to make a nice multi-faceted problem.

The apparent lower reed quality certainly amplifies any of the structural problems.
Logged
"You're making the wrong mistakes."
...Thelonius Monk

"I never made one of my discoveries through the process of rational thinking."
...Albert Einstein

"If Art Tatum took up classical music seriously, I'd quit my job the next day."
...Vladimir Horowitz

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403

Add mass to the top of the block to increase inertia, maybe ?
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683

Thank you all for the suggestions - I've tried most of these already to no avail.  I do think the issue is probably a combination of factors, but having come at it from many different sides with little to no ground gained, I'm at the point where all I can do is throw my hands up and acknowledge that I'm stumped and out of ideas (at least for the time being).  Unfortunately, I can't keep dedicating time to this old box given that I've already poured considerably more hours into it than I'm willing to charge for.  I actually have a hard time charging anything at all given that the final result isn't as satisfactory as I would like, although it's now certainly playable with a lovely (now quiet) action and a big, bright tone.  The situation sits a bit heavy on my shoulders, tbh...my mechanic friend down the road who owns his own garage once told me how he wants to be able to "hit it out of the park" every time for every client, but that sometimes you just can't...

Here's a quick and dirty audio clip of the box in action.  She's not perfect but there's life in her yet, I'd like to think (note that I'm bracing the box in place with the side of my face!):

https://www.dropbox.com/scl/fi/ca6i6ue5i4ezb0twedz31/Don-vintage-box-final.m4a?rlkey=dkadn4umcvvdw0zoqm2qvdbv2&e=1&st=sr2tiet1&dl=0

I've also attached a photo of the box in question.

« Last Edit: June 05, 2025, 11:13:32 PM by mselic »
Logged
C#/D player
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal