Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Tuning scratch location  (Read 1843 times)

0 Members and 1 Guest are viewing this topic.

jarviw

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 156
Tuning scratch location
« on: June 29, 2025, 07:04:45 PM »

I am probably searching the wrong keywords, and I am sure this topic has been addressed before -- but when you tune the reeds down, where do you remove the material to decrease the pitch and why? I am really asking from a physics theory point of view.

In my head I think it should around the node, 22.4% from the fixed point, but looking at the reeds I don't think that's the general practice?

I suppose the whole point is to reduce the vibration speed, either increase the length of the reed (not possible) or increase the mass  (momentum = mass x velocity). Scratching the reed doesn't do either... So I assume we are trying to move the location of the node when we scratch?
If that's the case, wouldn't the scratching location be extremely critical?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning scratch location
« Reply #1 on: June 29, 2025, 07:16:26 PM »

I don't know what you mean by the node.
As I understand it the way that scratching or file works to lower pitch is it makes the reed thinner and weakens the force that tries to return it to the rest position. So what you need to do is to remove metal along the part that bends, which roughly speaking is the half of the reed nearest to the fixed end.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

jarviw

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 156
Re: Tuning scratch location
« Reply #2 on: June 29, 2025, 08:08:08 PM »

I am really just confusing myself, but I am thinking along the concept of wind chimes (or xylophone etc) when you have a piece of material that vibrates at a harmonic frequency of its length. The nodes are where the material doesn't move at the harmonic wave frequency.

Wind chimes are usually open ended so the nodes falls on 22.4% from the ends. Reeds are fixed at one end so the math is different.  (I never really studied physics so honestly I don't actually know what I am talking about 😂 I may have to just read further on this subject)

If scratching at the lower end reduces the structural inertia, shouldn't it increase the frequency? Or alternatively, does it increases the total travel of the reed and therefore reduce the frequency?

(Really what got my to think about this is that I got myself a fun little toy piano that's horribly out of tune, and I start to think how tunning should be pretty similar to our reeds)
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Tuning scratch location
« Reply #3 on: June 29, 2025, 08:39:09 PM »

If you think about filing the tip of the reed to raise the pitch, this makes the tip of the reed lighter in relation to the fixed end.
If you scratch or file the fixed end it makes the tip heavier in relation to the fixed end, thus lowering the pitch.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: Tuning scratch location
« Reply #4 on: June 29, 2025, 09:28:57 PM »


    In physics a node is a point of no movement (as in guitar string harmonics).

   In this case that's effectively at the base of reed, or more properly the point where it no longer overlies the plate.
   There's no "hinge" on a reed, and  a steel strip it will vibrate in a curve, less at the base, increasingly towards the free end.

    So it's not like a pendulum and you'd need some linear algebra to calculate that. But we don't need to …

    Basically Rees and Theo's advice applies. Scratch near the base and it will vibrate slower, scratch the tip; faster.

    Intuitively there will be a gradient of effect along the length of the reed but I'm not aware of anyone trying to finesse that
Logged
  _       _    _      _ 

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Tuning scratch location
« Reply #5 on: June 29, 2025, 09:47:46 PM »

To put it another way:
Scratching below the halfway point of the reed has the effect of making the reed bend easier, and thus the tip travels further. With the amplitude being greater, it takes longer from one extreme to the other so sounds lower. (The wave is longer.) The same effect is made by adding weight to the far end of the reed, it swings further and slower. Of course, these differences are minuscule, but they do the job!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Tuning scratch location
« Reply #6 on: June 30, 2025, 08:24:20 AM »

I've made tuned windchimes.
If you've cut your length of pipe, gently let it slip through your fingers whilt tapping it, then the sound changes at this 'node' point.
It changes from a 'dink' clipped sound to a clear 'ding' sound where the tube rings clear.
I have in my mind a picture of the point where the sound wave stops before continuing along the pipe in another curve. As Chris says, no movement, and it is 22.4% of its length.

I don't think it has any context in reed manufacture...
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Tuning scratch location
« Reply #7 on: June 30, 2025, 11:00:02 AM »

For tuning purposes it's useful to think of the reedblade as a moving mass attached to a fixed point by way of a (torsional) spring. A large bass reed actually looks like that.

To reduce the vibration rate, weaken the spring (file/scratch mid-reed) or increase the mass (tip loading).

To increase the vibration rate, strenghten the spring (no practical way to do that) or reduce mass (file near tip).
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Tuning scratch location
« Reply #8 on: June 30, 2025, 11:12:12 AM »

Maybe not strictly melodeon related, but relevant here I think.
Due to my inherent thickness, I often wonder why the word "mass" has replaced "weight" in so many circumstances. Who can elucidate, please?
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Andy Next Tune

  • aka Andy Wooles
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1127
  • Melodeon with Accidentals? Make a PI Claim!!!
    • www.shavethedonkey.co.uk
Re: Tuning scratch location
« Reply #9 on: June 30, 2025, 11:49:28 AM »

Maybe not strictly melodeon related, but relevant here I think.
Due to my inherent thickness, I often wonder why the word "mass" has replaced "weight" in so many circumstances. Who can elucidate, please?
Mass is the amount of matter in an object (though matter may be difficult to define), but weight is the force exerted on an object's matter by gravity.
E.G an object may be weightless but will still have mass.
Logged
Andy, from the now ex-County Palatine of Cheshire

Caring for a European community of melodeons from France, Italy, Germany, Wales and Suffolk!

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Tuning scratch location
« Reply #10 on: June 30, 2025, 01:15:39 PM »

So mass equals volume? As one of our masters used to say (or rather, shout!) "Units boy, units!". What unit is mass measured in?
If mass isn't weight, then it wouldn't have an effect on the pitch of the reed, surely?
« Last Edit: June 30, 2025, 01:17:29 PM by Winston Smith »
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning scratch location
« Reply #11 on: June 30, 2025, 01:20:20 PM »

No mass definitely does not equal volume.
As long as you are living on the surface of the earth, where gravity is constant, you can use mass and weight interchangeably with no problem. We all do that all the time when we talk about weight in g and kg.  Among physicists these are units of mass,  the unit of weight is the Newton.  But don’t expect to get fruit if you ask the greengrocer for ten Newtons of Apples.
« Last Edit: June 30, 2025, 01:24:01 PM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: Tuning scratch location
« Reply #12 on: June 30, 2025, 01:28:29 PM »


  In school physics "mass" is just a measure of how much energy  (or force x time) it takes to accelerate a lump of "mass" … to a certain velocity. "Volume" doesn't figure in that.

  As Andy says, "weight" is different and depends what planet you are on. e.g. Your melodeon would "weigh" ± 1/6th as much on the moon? And wouldn't make any sound at all. Which is probably why the Apollo 11 astronauts didn't bother to take one along with them? 😉

   At university level it gets a whole lot more complicated … but there's no mention of melodeons there either. (Einstein played the violin).

Quote from: Theo
… don’t expect to get fruit if you ask the greengrocer for ten Newtons of Apples.

[edit]Your physics education is showing through a bit there, Theo.  Clever joke nevertheless!  😂
« Last Edit: June 30, 2025, 01:34:31 PM by Chris Ryall »
Logged
  _       _    _      _ 

jarviw

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 156
Re: Tuning scratch location
« Reply #13 on: June 30, 2025, 02:19:17 PM »

OK, so I consulted the higher being  ;D
Here's what Gemini tells me:  (I have to make edits due to the formulas not showing up correctly. I may have missed a few things...)


You're asking about the natural frequency of a cantilever beam, which is a good model for an accordion reed or similar vibrating mechanisms fixed at one end.

The formula for the natural frequency (f) of the fundamental (first) mode of a uniform cantilever beam is given by:

f= 1.8752 / (2 pi L2) * sqrt( ​EI / ρA)​​

Where:

    f = Natural frequency (in Hertz, Hz)

    L = Length of the beam (reed) (in meters, m)

    E = Young's Modulus of Elasticity of the beam material (a measure of stiffness) (in Pascals, Pa or N/m$^2$)

    I = Area moment of inertia of the beam's cross-section (in m$^4$). This accounts for the shape and distribution of the material in the cross-section.

    For a rectangular cross-section (like most reeds), I=wh3/12​, where w is the width and h is the thickness (or height) of the reed.

    ρ = Density of the beam material (in kg/m3)

    A = Cross-sectional area of the beam (in m2). For a rectangular cross-section, A=wh.

Let's break down how each parameter affects the frequency:

    L (Length): As you can see, L is in the denominator and squared. This means frequency is inversely proportional to the square of the length (f∝1/L2). So, making the reed shorter significantly increases its pitch. This is why filing the tip of an accordion reed (reducing its effective length) raises the pitch.

    E (Young's Modulus): This is in the numerator, so a higher Young's Modulus (stiffer material) leads to a higher frequency.

    I (Area Moment of Inertia): This is also in the numerator. Since I depends on w (width) and h (thickness), we can see:

        w (Width): Frequency is directly proportional to the square root of the width (f∝w​). Wider reeds tend to have higher pitches.

        h (Thickness): Frequency is directly proportional to the thickness to the power of 3/2 (f∝h3/2). This is a very strong dependence! Making a reed slightly thicker significantly increases its pitch.

    ρ (Density): This is in the denominator under the square root, meaning frequency is inversely proportional to the square root of the density (f∝ sqrt(1/ρ​) ). Lighter materials produce higher pitches.

    A (Cross-sectional Area): This is also in the denominator under the square root, meaning frequency is inversely proportional to the square root of the cross-sectional area (f∝1/sqrt(A) ​). Since A=wh, a larger area (due to more mass) generally leads to a lower pitch.

Combining I, ρ, and A:

If you substitute I=12wh3​ and A=wh into the formula, after combining constants:

f≈ 0.162/L2 * ​h * sqrt(E/ρ)​​

This simplified form clearly shows the dominant relationships:

    f∝1/L2: Length is the most impactful factor for tuning.

    f∝h: Thickness also has a strong direct relationship.

    f∝ sqrt(E/ρ)​: This term represents the material properties. A higher stiffness-to-density ratio results in a higher frequency.

Important Considerations:

    This formula is for the fundamental mode. Reeds also vibrate at higher frequencies (overtones/harmonics), which contribute to the instrument's timbre.

    Idealized Beam: This formula assumes a perfectly uniform, ideal beam. Real reeds might have slight imperfections or variations.

    Boundary Conditions: The "1.875" constant (more precisely βL=1.8751) comes from the specific boundary conditions of a fixed-free beam. Different boundary conditions (e.g., simply supported, fixed-fixed) would have different constants.

    Air Loading: For an accordion reed, the interaction with the airflow and the air within the reed chamber can slightly influence the actual vibrating frequency, although the reed's physical properties are the primary determinants.

    Mass at the End: If there's a significant concentrated mass at the free end (which isn't typically the case for a standard accordion reed but can be for other vibrating systems), the formula becomes more complex.

This formula provides the fundamental basis for understanding how accordion reeds are designed and how tuners make precise adjustments to achieve the desired pitch.
Logged

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: Tuning scratch location
« Reply #14 on: June 30, 2025, 02:50:21 PM »


   Good effort. But as soon as you scratch the surface of that equation you need tensors? 😳 (Young's modulus is naturally one). Don't go there!

   In the end it's just a scratch and adjust process. 
Logged
  _       _    _      _ 

Gena Crisman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1108
  • 🇬🇧
Re: Tuning scratch location
« Reply #15 on: June 30, 2025, 03:10:16 PM »

OK, so I consulted the higher being  ;D
Here's what Gemini tells me

OK... but... did you read it?

"This is why filing the tip of an accordion reed (reducing its effective length) raises the pitch."
Yes, I file the tips off of my accordion reeds to reduce their effective length all the time.

(e to add:) "frequency is inversely proportional to the square root of the cross-sectional area (f∝1/sqrt(A) ​)"
"(f∝w​). Wider reeds tend to have higher pitches"
"f∝h ... Making a reed slightly thicker significantly increases its pitch"
Yes. Inversely proportional famously means that if one number gets bigger, the other number also gets bigger...
"Since A=wh, a larger area (due to more mass) generally leads to a lower pitch."
Oh actually never mind it figured it out in the end. Or guessed, I mean, it was a 50/50...

"Mass at the End: If there's a significant concentrated mass at the free end (which isn't typically the case for a standard accordion reed"
I mean, my instrument has a lot of reeds with significant concentrated masses at the free end.

I would like to suggest that possibly it's not a great idea to consult an AI on matters such as this. I'm certainly not convinced the mathematics even follows through correctly from start to end, but, I haven't checked that.


edit: does I=wh3/12​, or does I=12wh3​ ?
« Last Edit: June 30, 2025, 03:24:56 PM by Gena Crisman »
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Tuning scratch location
« Reply #16 on: June 30, 2025, 04:07:23 PM »

"We all do that all the time when we talk about weight in g and kg."

OK, then if we talk about pounds and ounces (is that allowed again?) we can call it weight, but in kg etc. it's mass. Is that about right?
I'm so pleased that I can call upon such a wealth of knowledge here on melodeon.net!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: Tuning scratch location
« Reply #17 on: June 30, 2025, 04:26:58 PM »


   I've not used pounds and ounces professionally since … about 1973. Shopping … 25 years ago.

   Which "ounce" are you advocating?  The avoirdupois ounce (28.35g)?  The troy/apothecaries 'ounce (31.103g)?

   Or the fluid ounce (1/16th of a pint)? it doesn't make much sense physically. But … melodeons do get played in pubs!  😂
Logged
  _       _    _      _ 

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning scratch location
« Reply #18 on: June 30, 2025, 04:27:57 PM »

Time to get back to the topic.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Tuning scratch location
« Reply #19 on: June 30, 2025, 05:00:35 PM »

when you tune the reeds down, where do you remove the material to decrease the pitch and why? I am really asking from a physics theory point of view.

At the base of the reed, where it's flexing most while vibrating.
Physics:
A reed is basically a classic "mass + spring" resonant system.
Filing the tip of the reed reduces the mass, raising the frequency.
Filing the base of the reed (near where it's riveted on the plate) reduces the stiffness of the spring, which lowers the frequency.

That's all you need to know.

(In some cases the frequency of a reed is reduced by adding weight to the tip, but that's usually a design decision rather that a tuning procedure: it's a compromise to get bass reeds to fit without making the instrument bigger than you wanted it.)
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal