Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: how are reeds tuned?  (Read 5462 times)

0 Members and 1 Guest are viewing this topic.

burnt nial

  • Member
  • *
  • Offline Offline
  • Posts: 37
how are reeds tuned?
« on: December 15, 2009, 08:21:24 PM »

I just removed the bass reed blocks from my Double Pay so I can send 'em off to be changed to the Joe Burke layout. I'm wondering if the reeds have to be installed on the blocks before final tuning? Do they come from Hohner with the plastic flapper valves already installed? How far off tune are they when they come from the factory? They all look so near alike to me that mixing them up would seem real easy to do and I can see no identification marks on them. This looks like a job that could drive a person nuts.
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: how are reeds tuned?
« Reply #1 on: December 15, 2009, 08:34:57 PM »

There are no identifying marks. They are easily identified by the note they sound when aimed at an electronic tuner.
They are rough tuned to within around 10 cents at the factory. Sometimes they arrive with valves, sometimes you have to fit valves yourself.

The job drove me nuts, years ago, and I think Theo's pretty far gone too!
How we suffer for our art.  :||:
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

dr.harp

  • Member
  • *
  • Offline Offline
  • Posts: 14
Re: how are reeds tuned?
« Reply #2 on: December 15, 2009, 09:37:42 PM »

The reeds must be waxed on the block for the final tuning and in some cases the blocks must be in the accordion, although this is rare with melodeons but a must with large piano accordions. Bass reeds are usually supplied with valves glued on, as are the chord reeds. The only reeds I receive from Hohner without valves are some of the higher treble reeds and, on occasion, some of the midrange treble. It is best not to mix up the reeds as once they are off the block it is a pain to identify them with a tuner unless you hold them on a block and blow - most tuners are not responsive enough to pick up the note just by flicking the reed tongue. Once the reeds are on the block, tuning is not a problem.
Logged
Owner of Wilson Music Services - Repairs to accordions and harmonicas, specializing in Hohner.

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: how are reeds tuned?
« Reply #3 on: December 15, 2009, 11:22:29 PM »

The reeds must be waxed on the block for the final tuning and in some cases the blocks must be in the accordion, although this is rare with melodeons but a must with large piano accordions.

If you have the time, could you elaborate on this?
Regards,
Bruce
Logged

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: how are reeds tuned?
« Reply #4 on: December 16, 2009, 12:20:54 AM »

I do fine tuning with the reed blocks in the box, I would say it was pretty crucial to get a really accurate fine tune particular to the instrument.
Logged

burnt nial

  • Member
  • *
  • Offline Offline
  • Posts: 37
Re: how are reeds tuned?
« Reply #5 on: December 16, 2009, 03:51:32 AM »

I do fine tuning with the reed blocks in the box, I would say it was pretty crucial to get a really accurate fine tune particular to the instrument.
How do you get at the reeds that are under the leather or plastic valves? I can see scratches on the reed blades which I presume were made when fine tuning. But to do it in the box would require a lot of assembling and disassembling the accordion. A huge amount of time and expense, no? Not to mention all the opportunities to screw something up.
Logged

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: how are reeds tuned?
« Reply #6 on: December 16, 2009, 08:41:57 AM »

But to do it in the box would require a lot of assembling and disassembling the accordion. A huge amount of time and expense, no? Not to mention all the opportunities to screw something up.

After 30 + years experience of tuning reeds, you get to know just about how much or how little filing is needed to obtain, say, a 5 cent rise or fall in pitch, so excessive assembly and disassembly is not really an issue.

The first thousand melodeons are the most difficult....   ;D



Logged
Tuner/repairer, now retired.

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: how are reeds tuned?
« Reply #7 on: December 16, 2009, 09:27:41 AM »

If you look under the plastic valve you can often see a scratch on the belly of the reed tongue if it needed to be made flatter. I've got a little home made tool which is a wooden handle with a piece of piano wire bent into J shape at the end. You can put this down the side of the top reed and poke it under the other reed to push the tongue up. Once it's up I put a blunted Stanley knife blade under it to stop it returning to position, remove the poking tool and set about it with my files.

As Malcolm said, you get to know how much to file on the different sizes of reeds - a low bass note would loose a lot of metal for a 5c rise where as a high G reed would need very little. Tuning is generally time consuming, but it's quite easy with a little patience. The main trouble I had with my first goes of tuning was being over zealous and taking too much off at once meaning it was far too sharp and then far too flat, just because I wasn't doing it a little at a time to be accurate.

You can tune with the reed block in place usually, I take the other blocks out to give myself more room. And you don't have to put all the bellows pins back in once its re-assembled to try a note - most airtight boxes with good neoprene seals will hold together to play a test note before dis-assembly.
Logged

dr.harp

  • Member
  • *
  • Offline Offline
  • Posts: 14
Re: how are reeds tuned?
« Reply #8 on: December 16, 2009, 12:59:42 PM »

Quote
But to do it in the box would require a lot of assembling and disassembling the accordion. A huge amount of time and expense, no? Not to mention all the opportunities to screw something up.

Like LJC I use a reed hook to lift an internal reed to facilitate filing the tip, if the pitch needs sharpening. Conversely, a tuning iron (a rod with rounded, high carbon, steel tips) is used to scratch the base of the reed if lowering the pitch is required. Using the reed hook enables a tuner to keep the block anchored in the accordion so the only dis-assembley is lifting the housing on and off the bellows.

On small melodeons it is easier to remove the reedblock and put it on a test bellows to do the tuning and be fairly confident that when the block is re-installed there is no variation in pitch. This can be simply checked with an electronic tuner, checking pitch of a few particular reeds (usually a low, middle and high) both on the test bellows and back in the box. On most melodeons the pitch will remain constant. There are, however, occasions when the tuning done on a test bellows can end up being  totally wrong once the blocks are re-installed in the accordion housing and fit back onto the bellows. This usually happens on instruments like a Shand and, especially, on large PA's. The fluctuation of pitch can be quite a lot and not consistent across the range of notes.

As Malcolm said, after a quarter century of tuning and (for me) thousands of repairs, you get to know how much to raise or lower pitch to accommodate the variances when re-installing reedblocks. To spare myself the agro, I just tune the large melodeons and PA's with blocks installed and continue to use a test bellows for instruments like the Erica. The lifting on and off of the treble housing from the bellows is far less annoying than finding out you botched a tuning job by trying to take the easy route of removing the reedblock.
Logged
Owner of Wilson Music Services - Repairs to accordions and harmonicas, specializing in Hohner.

Bill the Farmer

  • Not quite so
  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 497
  • Hohner Club, Liliput...
    • Bill Farmer
Re: how are reeds tuned?
« Reply #9 on: December 16, 2009, 02:20:38 PM »

What about the large bass reeds with a lump of brass soldered on to the end? I assume you would want to file a little bit off of the lump of brass to sharpen it, how would you do that on the inside reed?
Logged
Bill of Old Radipole Village

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: how are reeds tuned?
« Reply #10 on: December 16, 2009, 02:37:57 PM »

There is so much give in the largest bass tongues that its no problem to lift it and file at the brass lump on the end.
Logged

dr.harp

  • Member
  • *
  • Offline Offline
  • Posts: 14
Re: how are reeds tuned?
« Reply #11 on: December 16, 2009, 03:07:58 PM »

Remember that those of us replying on this topic are referring to doing touch-up and fine tuning, not reconfiguring a bass system by altering reeds a semitone or whole tone. When doing that sort of tuning, the reedplate is usually removed from the block (especially when working on internal reeds), the bulk of retuning done and then the plate is re-waxed and the fine tuning completed. It comes down to efficiency and deciding what takes the least time, tuning a waxed on plate or removing, tuning and re-waxing. Also to consider is that when tuning the small reeds there is always the danger of bending the tip of the reed when using the reed hook method. Sometimes it is just better to pop the reed off, file (or scratch), loosefit the plate on the block to check it and when your ear is satisfied, re-wax.
Logged
Owner of Wilson Music Services - Repairs to accordions and harmonicas, specializing in Hohner.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: how are reeds tuned?
« Reply #12 on: December 16, 2009, 04:11:57 PM »

If you look under the plastic valve you can often see a scratch on the belly of the reed tongue if it needed to be made flatter. I've got a little home made tool which is a wooden handle with a piece of piano wire bent into J shape at the end. You can put this down the side of the top reed and poke it under the other reed to push the tongue up.

That's the Italian method for lifting the inside reed.  The method is tried and tested, and works very well.  The German method is more difficult to understand so I posted some pictures a while back, here is the link.   I tend to prefer this method because you only need the one tool to lift and support the reed, so for me its a little quicker.   The hook method is better in the restricted space when the reedblocks are installed in the instrument.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: how are reeds tuned?
« Reply #13 on: December 16, 2009, 04:34:04 PM »

If you look under the plastic valve you can often see a scratch on the belly of the reed tongue if it needed to be made flatter. I've got a little home made tool which is a wooden handle with a piece of piano wire bent into J shape at the end. You can put this down the side of the top reed and poke it under the other reed to push the tongue up.

That's the Italian method for lifting the inside reed.  The method is tried and tested, and works very well.  The German method is more difficult to understand so I posted some pictures a while back, here is the link.   I tend to prefer this method because you only need the one tool to lift and support the reed, so for me its a little quicker.   The hook method is better in the restricted space when the reedblocks are installed in the instrument.

That was very interesting Theo, although I confess that I am still not entirely sure how the lifter can pull up the suck reed :|bl You slide it in above the tip and then pivot back? Wouldn't that damage the tip?
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: how are reeds tuned?
« Reply #14 on: December 16, 2009, 05:07:30 PM »

That was very interesting Theo, although I confess that I am still not entirely sure how the lifter can pull up the suck reed :|bl You slide it in above the tip and then pivot back? Wouldn't that damage the tip?

You would think so wouldn't you?  But in practice it works.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: how are reeds tuned?
« Reply #15 on: December 16, 2009, 05:17:49 PM »

That was very interesting Theo, although I confess that I am still not entirely sure how the lifter can pull up the suck reed :|bl You slide it in above the tip and then pivot back? Wouldn't that damage the tip?

You would think so wouldn't you?  But in practice it works.

Fair enough :P I'll have to try it when I get a junk box.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal