Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: where to get valves, how to clean reed plates  (Read 1750 times)

0 Members and 1 Guest are viewing this topic.

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
where to get valves, how to clean reed plates
« on: August 11, 2025, 07:13:15 AM »

I'm about to embark on my biggest job yet: completely revalving a (I think) prewar chromatic button accordion ( a Hohner Sirena III, made in Switzerland)
What would be the best place to order my valves? I'm in the Netherlands.
My second question is about cleaning the reed plates. I replaced all valves of a melodeon once, and cleaning the reed plates was a tedious job, scraping off the old wax. Is there a solvent I could use? What's the best way to remove old wax?
For waxing I used to put a small container on my gas stove, but the wax was getting too hot so I had to put out and re-ignite the fire regularly.
Any advice for a good electric wax heater?
Thanks in advance!
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: where to get valves, how to clean reed plates
« Reply #1 on: August 11, 2025, 08:39:20 AM »

My first bit of advice would be not to start on a CBA. Been there, done that. Learning curve is too steep. Too many reeds, pallets, buttons, levers, Stradella.
Work on smaller boxes. 1-row or small 2-row, until you get good & fast at this job.

For cleaning, acetone works a dream, but it's quite nasty to your health and the fumes are combustible, so don't light up a fag in celebration after you've done a long cleaning job. In fact, better don't smoke at all - it's also quite nasty to your health.
IPA (IsoPropylAlcohol) and scraping is how I do it. Very long and tedious but significantly lower health hazards. When cleaning by hand make sure the bottoms of the slots are clear and don't have gunk stuck in them.

For wax a baby bottle warmer melts the wax but doesn't get it quite hot enough for optimal performance. I use it for initial wax transfer.
Learn to use a modified soldering iron for spot-waxing, waxing thin gaps, truing up the wax job - it's a real game changer.

For parts, easiest approach might be to order from Carini.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: where to get valves, how to clean reed plates
« Reply #2 on: August 11, 2025, 09:12:21 AM »

Carini is the best if you want larger quantities.   For smaller quantities there are sellers on eBay for example https://www.ebay.co.uk/sch/i.html?sid=ha-vent&_pgn=1&isRefine=true&_trksid=p4429486.m3561.l49496

I’ve been cleaning old reeds for 20 years.  I’ve not found a way that’s not tedious. Solvents have their place but only to remove what remains after mechanical cleaning.  And solvents come with fire and health hazards.  I’ve tried ultrasonic cleaners but again only effective after mechanical cleaning.
Tools I use include an old small kitchen knife with half the blade broken off and the end ground to a right angle.  A blunt blade is best.  Wax and glue don’t need a sharp blade to remove and there is less risk of removing wood. After scraping with the dull blade a soft wire brush is excellent for removing the last remaining wax from reed blocks and reeds.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: where to get valves, how to clean reed plates
« Reply #3 on: August 11, 2025, 01:22:08 PM »

I found the best thing for getting old wax off the faces and edges of reed plates is the good old fashioned thumbnail.
If you are doing so many so fast that it wears down too much for a manicure to make it smooth again, nature has kindly provided a spare on the other hand.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
Re: where to get valves, how to clean reed plates
« Reply #4 on: August 11, 2025, 05:10:01 PM »

Thanks all! I'll be doing this job anyhow as I want to play the instrument by the end of the year.
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: where to get valves, how to clean reed plates
« Reply #5 on: August 11, 2025, 07:02:06 PM »

That's a lot of reeds there, Willem! I don't envy you your work. (And that's before you start on the basses!)
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: where to get valves, how to clean reed plates
« Reply #6 on: August 12, 2025, 01:57:40 PM »

An essential ingredient when cleaning/refurbishing old reeds is something to listen to. In the UK BBC Sounds has some great documentary programming ( Real Dictators is a personal favourite, narrated by Paul McGann).

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
Re: where to get valves, how to clean reed plates
« Reply #7 on: August 12, 2025, 06:00:39 PM »

Yes, it’s a lot of valves! I decided to go for the low hanging fruit and started with the bass side. But I got an unpleasant surprise: the biggest block is permanently attached to the ground plate. I will have to apply wax carefully! Have any of you encountered this? See attached picture.
The highest voice block did not have any valves. I cleaned the reeds and blocks and waxed the reed plates back on. Now I first have to get a lot of valves. I’m considering buying an electric wax pot, but I may not really need it. My spoon and pot on the stove have done a good job today.
(and yes, having something to listen to is important!)
« Last Edit: August 12, 2025, 06:03:31 PM by Willem Feltkamp »
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: where to get valves, how to clean reed plates
« Reply #8 on: August 12, 2025, 08:10:26 PM »

Yes, I've done a lot of glued in blocks (in fact I just finished one). A couple of tips… when you wax on the big reeds, do it with the other block out and mask off the adjacent reed holes under the removable block to avoid getting wax in one of these (it will be waxed shut). If that happens you can be in a world of pain trying to clean it off the underlying pad, and it being the bass side you may have to dismantle the bass machine if it’s an old style bass machine, to get to the pallet.
I also tend to use a lot less wax than you. It's not necessary to have big fat beads…it's more like a runny glue and you can use a soldering iron and gravity to persuade it around the reed.
« Last Edit: August 13, 2025, 07:23:37 AM by Rog »
Logged

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
Re: where to get valves, how to clean reed plates
« Reply #9 on: August 14, 2025, 07:16:31 PM »

Rog, you describe my horror scenario! I thought of taping the holes to protect them. I'll also try to get the reed plates very tight on the wood (maybe with a little bit of wax applied with a paint brush) to prevent wax getting to the holes inside the block once i start to properly wax them in place.
I have used more wax than I intended; it was probably a bit too hot so too much flowed out of the spoon. I think I prefer the spoon to a soldering iron: when done right waxing a block takes mere minutes.
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: where to get valves, how to clean reed plates
« Reply #10 on: August 15, 2025, 03:25:58 PM »

I come across the glued-in bass block on PAs often. I always put the bass end on its side, so that the side of the glued-in block that I’m working on is facing upwards when waxing. It’s much easier to wax this way and much less likely to get wax where you don’t want it (such as in the adjacent holes). Tape off the holes anyway. You can rest the block/bass end on something that will support it so that it doesn’t move while waxing, leaving both hands free to work.
Logged
C#/D player

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: where to get valves, how to clean reed plates
« Reply #11 on: August 17, 2025, 11:32:37 AM »

My technique is to tack the reed in place (a few dabs at the foot) then hold the bass end in one hand and move it around to control the flow, as I apply wax with a flat spoon. As in this video, but instead of holding the reed block you actually grasp the entire bass end and wiggle it about. Sometimes i can get my left thumb to hold the plate in place as well as the bass end. This way you can control exactly where the wax goes. Having the bass end on a table isn't good enough. And I do this with substantial PA bass ends…

https://youtu.be/SA0w5HSwp_0?si=Qa6PP4Fj5k5S_Jxl
« Last Edit: August 17, 2025, 11:36:36 AM by Rog »
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: where to get valves, how to clean reed plates
« Reply #12 on: August 17, 2025, 02:40:20 PM »

Rog, after watching that, I'm going to have to find my wax pot and give it another go. It looks so easy!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
Re: where to get valves, how to clean reed plates
« Reply #13 on: August 29, 2025, 08:45:24 PM »

Thanks for all advice and tips! I’m a bit confused about the model of the wax spoon. I’ve seen it before, but it doesn’t seem to be able to hold a lot of wax. Maybe that’s the point?
I had a setback; after cleaning all reed plates and blocks I’ve been eagerly awaiting the valves. Turns out that the hole in them (Hohner valves) was not on the photo in the web shop, so most bass valves are too short since I measured total length required.
Also they’re not leather but some kind of surrogate (Vileda?). Is that any good? Finally, I would have liked to have them just 1 mm narrower, but that size was not available. I’m starting to think that maybe getting the valves in the right place might be the most difficult part of the job. I'm even considering buying a piece of leather and cutting the valves to size myself.
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: where to get valves, how to clean reed plates
« Reply #14 on: August 29, 2025, 09:30:49 PM »

You can cut down the vileda with a very sharp blade. Use a steel rule and a cutting board.
I rarely use Hohner valves with punched holes. You can see in the video
I made a couple of spoons for waxing out of whatever was available
One flat one from ordinary 1mm steel and the one I use in the video was made from a Bean can.
I've since made a better shaped one that gives nice access for between glued-in reedblocks .
Here's a not very interesting video.
https://youtu.be/cP8DP_mnNQ0?si=U5zXX8ytT7NFlprc
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: where to get valves, how to clean reed plates
« Reply #15 on: August 29, 2025, 10:49:32 PM »

With plastic valves, you don't need the hole for the rivet. For the treble side I have 3 or 4 valve sizes and glue on the smallest until the  slot is too big, then move on to the next biggest valve. I always glue the valve on first then trim them in situ with a sharp pair of short bladed sewing scissors.
The wax 'spoon' in my video is just a flat sheet of metal, and it works a bit like a giant pen nib. Plenty of wax clings to it.

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
Re: where to get valves, how to clean reed plates
« Reply #16 on: August 31, 2025, 11:24:25 AM »

Good news! I used a bunch of valves I already had for the biggest reeds. I thought they were too wide but simply moved them closer to the inside of the reed plates. Cut the vileda to the right width and put everything in place. So the bass side is now finished (that is, apart from the tuning). It has five voices and I really like the sound.
I did wonder: I cut the (plastic) valves to length but didn't bother to also shorten the supporting layers. Do you have any opinions on this?
Logged

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
Re: where to get valves, how to clean reed plates
« Reply #17 on: September 07, 2025, 11:02:49 AM »

Update: I successfully replaced all 378 valves and waxed all reed plates back in place.
On the bass side I forgot to trim the support layers of the valves. What’s your experience concerning the importance of adjusting valve stiffness?
The coming weeks my neighbours are going to hate me; tuning, tuning, more tuning….
Logged

-Y-

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 896
  • Handry 18 (G/C), Mélodie (D), Club IIb (A/D)
    • a database of nearly 500 melodeons here
Re: where to get valves, how to clean reed plates
« Reply #18 on: September 07, 2025, 11:22:17 AM »

On the bass side I forgot to trim the support layers of the valves. What’s your experience concerning the importance of adjusting valve stiffness?

It's an important part of setting valves, I think. Setting them too stiff can stifle the reed. But they can also make unwanted noises if that's too loose, or badly pressed on the whole length against the reed.
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal