Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Button "depth"  (Read 1318 times)

0 Members and 1 Guest are viewing this topic.

Lew Morris

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 215
Button "depth"
« on: September 04, 2025, 10:54:57 PM »

Are these buttons below the surface of the keyboard "normal"?

Put another way, is something amiss here?

If so, what might be the cause(s)?

What would be the remedy?

EDIT

Added a second photo.

This is an instrument that I'm considering to purchase. IF...

The seller claims it to be a "40's HA2815" ... the keyboard box "looks" like plastic, to me.
« Last Edit: September 04, 2025, 11:23:09 PM by Lew Morris »
Logged
"It's what you learn, after you know it all, that counts." John Wooden

JNM SY

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 227
Re: Button "depth"
« Reply #1 on: September 04, 2025, 11:09:21 PM »

 Check first that the keyboard is seated properly in the right position. I doubt that the buttons would be deliberately set as low as that.Loosten the 2 screws on the inside of the fondo, and try moving the keyboard into a better position. Good luck.👍
Logged

Fionn

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 194
Re: Button "depth"
« Reply #2 on: September 05, 2025, 12:02:12 AM »

It looks remarkably like the plastic keyboard I've just reattached to my Double Ray after cleaning the keys (tip: never underestimate how sticky a four-year-old can be). Right down to the type of thumb strap leather and the angle of attachment.

Even if it is, the keys shouldn't sit that low. Might it be caused by something simple like the sockets for the long screws that attach the fingerboard not being in quite the right place for a replacement plastic one?
Logged
Vintage Double Ray C#/D

Lew Morris

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 215
Re: Button "depth"
« Reply #3 on: September 05, 2025, 02:52:00 AM »

Thinking I'll take hard pass on this one.

Looks like a retro-fitted plastic keyboard box, and ill-fitted at that.  $325USD was the asking price, and I'm probably able to re-fit it, but I'm not looking for a project.

EDIT

Added photo

One end of the keyboard box looks like it was cut off (to make it fit?).

« Last Edit: September 05, 2025, 02:57:39 AM by Lew Morris »
Logged
"It's what you learn, after you know it all, that counts." John Wooden

Lew Morris

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 215
Re: Button "depth"
« Reply #4 on: September 06, 2025, 05:34:13 PM »

Lester did a video on replacing the keyboard.  Unfortunately the keyboard he used as a replacement (Acorn) is no longer available. I didn't ask Pete "why", but I suspect minimum production orders for injection molded part wasn't worth the expense. Don't know for sure, just speculating.

I spent some time looking for used parts, but it appears the only solution would be to find a suitable 'donor' for parts.  Too bad I don't know how to do 3D modelling, this would be a great 3D printer project.
Logged
"It's what you learn, after you know it all, that counts." John Wooden

Fionn

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 194
Re: Button "depth"
« Reply #5 on: September 06, 2025, 05:48:31 PM »

If it needs a fingerboard the same size as the Erica, you can buy them from fairly inexpensively from Hohner.

https://www.hohner-cshop.de/en/Akkordeon/Diatonic/2-row/Erica/GRIP-cpl-With-Thumb-Strap-Erica.html?force_sid=4f9cde29cfef017c393e8ec37051fd83

Logged
Vintage Double Ray C#/D

Lew Morris

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 215
Re: Button "depth"
« Reply #6 on: September 06, 2025, 06:50:05 PM »

Thanks Rees.  This isn't "my" Pokerwork, I was considering purchasing it.  Closer inspection of the seller's photo reveals that one end of the keyboard is actually broken off and not seated properly. Whether is was by accident, or the result of a very poor repai, is unknown to me.

I have the skills to fabricate a new keyboard, it's just a matter of investing the time. In this particular situation the old keyboard is not 'original' so using it as a template isn't possible.

I was/am looking for my second box to expand my playing. To that end, undertaking a rebuild is probably dillusional ... not an uncommon condition for to me.

Logged
"It's what you learn, after you know it all, that counts." John Wooden

Lew Morris

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 215
Re: Button "depth"
« Reply #7 on: September 06, 2025, 06:54:34 PM »

I'd emailed Pete about these keyboards, and just received a reply. 

The replacement keyboards he made were milled from solid Beech, with Birch ply top and bottom.

This would make a good 3D modelling/printing project, if I knew how to do such things. .. ..

Logged
"It's what you learn, after you know it all, that counts." John Wooden

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: Button "depth"
« Reply #8 on: September 06, 2025, 07:22:25 PM »

I'd emailed Pete about these keyboards, and just received a reply. 

The replacement keyboards he made were milled from solid Beech, with Birch ply top and bottom.

This would make a good 3D modelling/printing project, if I knew how to do such things. .. ..

pete told me he had to stop making them as it was way too time consuming for the price he charged (around £50).....i made a few myself with my friend graham whitmore....it was indeed very time consuming and the wood and aircraft ply werent cheap either....then there was time and expense staining and finishing with liberon finishing oil. if someone could find a way of producing them in numbers im sure there would be a "big" demand.....plenty of pokerwork and erica players who would prefer a wooden fingerboard with removeable back so that button travel can be cushioned and limited. Id buy more than a few! pete was invaluable help explaining a few tricks he'd learnt along the way. top man!
Logged

pete /acorn

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 930
  • .Cast Trilly
    • Acorn Instruments
Re: Button "depth"
« Reply #9 on: September 07, 2025, 09:08:57 AM »

Hi,
To make these there are many operations.
There are 3 beech components for the frame and 2 ply panels.
Machines used,circular saw,planer thicknesserspindle moulder,overhead router,edge sander,hand sanding and painting.
I used to make 100 at a time.
When spray painting it is very difficult to get a constant finish in a small shop.
There is a tremendous amount of work.
I got customers who complained about the slightest paint blemish or imperfection
I decide life was too short.
Re the one in the picture it would be easily fixed.
Logged
Acorn Instruments are specialist retailers of Castagnari Instruments,and have an extensive stock of new instruments on the shelf for prompt delivery in standard layouts however these can easily be changed to customers special requirements,we have over 600 reeds in stock
 We also have the largest stock in the UK of  pre loved melodons all fully serviced,and with 12 months warranty
UK and international customers catered for
www.acorninstruments.co.uk

Lew Morris

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 215
Re: Button "depth"
« Reply #10 on: September 07, 2025, 08:39:52 PM »

Thanks for filling in the blanks Pete

By "the one in the picture it would easily fixed" do you mean the keyboard assembly could be repaired? Or, the instrument, as a whole, would easily be repaired?

I haven't purchased it yet, but am giving it serious consideration. I was a modelshop patternmaker for many years, so I'm not too daunted by the idea of starting from scratch, if need be.

 The damaged keyboard, in the first set of images, appears to be plastic, with one end broken off.   That, in itself, isn't a problem, but it does lead me to wonder what else the "repairer" inflicted on this box.

I've been seeking the elusive DG here in the States, but this instrument, in AD, would get me along.
Logged
"It's what you learn, after you know it all, that counts." John Wooden

Lew Morris

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 215
Re: Button "depth"
« Reply #11 on: September 07, 2025, 11:30:29 PM »

I'm not intimately familiar with Hohner boxes, so I'm not sure how to phrase this question.

This regard to this box I'm thinking of buying; I believe it is a 2815.

 How interchangeable are the keyboard boxes; e.g., will the plastic 2915 part retro fit to the 2815?

Is it "as simple" as replacing reed(s) block(s) to change this instrument from A/D, to a D/G?
Logged
"It's what you learn, after you know it all, that counts." John Wooden

Fionn

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 194
Re: Button "depth"
« Reply #12 on: September 08, 2025, 01:15:46 AM »

I've been seeking the elusive DG here in the States

Someone told me about importing an accordion the other way round, from the US into the UK. It wasn't even very valuable, but it was going to cost much more in duty and fees than seemed reasonable for an old accordion.

Long story short, a relative sent him the bass end as salvaged parts, which didn't attract duty. The treble cabinet followed some time later, and as the bellows needed replacing anyway he bought one locally. Voilà! One vintage accordion in kit form.

It might have fallen into a legal grey area even though the parts sent from the US didn't add up to a playable instrument, so I'm telling you the story rather than recommending it...  :-X
Logged
Vintage Double Ray C#/D

Lew Morris

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 215
Re: Button "depth"
« Reply #13 on: September 08, 2025, 01:55:06 AM »

Quote
so I'm telling you the story rather than recommending it...

The friend here exports American vintage cars in "kit" form; at least a 40' container worth a year. Sometimes more than one. The shipping container comes back with old motorcycle "parts"

There are plenty of derelict Hohner boxes here, usually around $150-200USD-ish.  I was wondering, for example, if I could salvage G reeds from one, and stick them into this old AD. I'm sure it isn't quite as simple as that, there would probably be tuning involved. 

Logged
"It's what you learn, after you know it all, that counts." John Wooden

Lew Morris

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 215
Re: Button "depth"
« Reply #14 on: September 08, 2025, 02:01:02 AM »

It's all a moot point now.

I had emailed the seller asking how he determined that the box was  AD.

This was his response.

Quote
My deepest apologies, I had two Vienna's 1 A/D and a C/F. Gave one to my granddaughter a few years back thinking it was the C/F. Just checked this one using a tone analyzer holding the third buttons down and closing the bellows and the two tones were C & F took the keyboard end off and both reed boxes are stamped C-F.

I am so glad you questioned me before I sold this to someone. I will correct the listing and again my deepest apologies.

Bob
Logged
"It's what you learn, after you know it all, that counts." John Wooden

Fionn

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 194
Re: Button "depth"
« Reply #15 on: September 08, 2025, 02:59:46 PM »

It's all a moot point now.

 :(

If you wanted a playable box in a less common tuning in Britain, you'd contact folk who repair and restore accordions and ask if they'd anything suitable on the workshop shelf that they could set up for you. If you wanted a specific model there might be a long wait, but less so if you were flexible.

Is that not an option in the States?

It's not the cheapest way of doing it, unless you take into account the tools, hard to find components and hours of learning and experimenting it would take to set up a box to the same standard yourself, in which case it probably is.



Logged
Vintage Double Ray C#/D
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal