Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Resticking curling celluloid  (Read 560 times)

0 Members and 1 Guest are viewing this topic.

Helena Handcart

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2452
  • Saltarelle Nell
Resticking curling celluloid
« on: September 15, 2025, 10:28:38 PM »

Advice please Melnetters, I have a Hohner Club 2 for restoration. Cosmetically the box is in reasonable condition however some of the celluloid panels are peeling back a little at the edges. What's the best method for resticking the peeling edges?
Logged
Saltarelle Le RomanĂ©  | Saltarelle Nuage | Oakwood | various elderly Hohners

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Resticking curling celluloid
« Reply #1 on: September 16, 2025, 07:34:25 AM »

If this is a junker box that you don't really care about too much, and you want to do a quick job, I'd consider PU glue (like Gorilla original).
But once it's in the joint, it's in the joint and there's no easy way to reverse it if things don't go well.

I think this has less potential for things to go wrong compared to partially dissolving the celluloid with acetone and trying to re-glue it naturally.
I've done it before with success, but I can see why this can be frowned upon due to complete non-irreversability.

Experts, please correct me if I'm horribly wrong - my area of expertise is wood, not celluloid.
Logged

Lars

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 797
Re: Resticking curling celluloid
« Reply #2 on: September 16, 2025, 08:01:15 AM »

I've done this with various glues - the best results was with a nasty smelling semi-gelled CA-glue, but old-style with just acetone was good too, as was a PU-glue.

Prep is everything though. Don't skip that part :)

If it's the classic case of celluloid shrinking and pulling/curling at the corner, then you may have some wood fiber stuck to the underside of the celluloid that won't perfectly match up if you just squeeze it flat against the wood cabinet again. A good idea is to mask off the top of the celluloid with masking tape a good bit futher back than the lifting bit, and also cover the metal corner (and other nearby parts where you don't want to risk getting glue). Some glues will dissolve or mis-colour celluloid upon slightest blob, thus the masking. Also doing a try-run with clamps a couple of times is never a bad idea, when you're working with somewhat fast setting glues - and it can help you position the clamps in a way where run-out is easy to wipe off without wiping over any other surface that's not masked off.

If you're working with glue that can slightly soften celluloid, don't forget to use a clamping caul. You don't want footprints of a clamp pressed into the celluloid as a reminder of the job done :)

Mask off, see if you can pull some fine sandpaper a few times in the slot to clear old bumps, clear out debris and dust, apply glue as far into the opening as you can, clamp, wipe off runout, wait, and finish off with a bit of a clean.
If there's slight glue on the very edges after removing masking tape, a few careful scrapes with a sharp knife can be helpful.


Others might have different approaches, but this works for me. Have fun getting the box back in action!
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Resticking curling celluloid
« Reply #3 on: September 16, 2025, 08:59:23 AM »

If you use pu glue, it will follow water as it's moisture activated. So do the prep exactly as Lars says then put a few drops of water in the joint and rub the celluloid down, trying to force the water to creep all the way to where the celluloid is still attached.
A few drops of glue into the joint then again rub to encourage the glue to creep right in.
Now clamp it tight. A bit of cut down plastic milk bottle shiny side to the repair is a good start, even better with a quick polish with furniture wax first. Now a bit of ply to spread the effort (tha caul, as already said) and stick a clamp on.
Pu sets in 20 minutes, but should be left overnight if you do the repair in the evening.
Polishing out any unevenness afterwards is your next fun job.
« Last Edit: September 16, 2025, 09:00:59 AM by Squeaky Pete »
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

JNM SY

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 227
Re: Resticking curling celluloid
« Reply #4 on: September 16, 2025, 10:30:55 AM »

I've used CA glue on a feeler guage to get it under the edge on an old box and its worked - BUT- I've had many disasters with CA glue and would advise not putting it anywhere near a box now.( esp.the low viscosity stuff which gets everywhere!)
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Resticking curling celluloid
« Reply #5 on: September 16, 2025, 07:54:21 PM »

I'd caveat what Pete said about PU glue - at least with Gorilla there's enough moisture in the air to activate it and too much water weakens the bond. Some people dampen the surfaces, others, like me, glue dry (never had a problem). Just don't pour too much water onto it as it will foam all over the place.

CA is a great glue but you do need to know how to use it.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal