Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3 4 5   Go Down

Author Topic: Resonance issues with reedblocks  (Read 6910 times)

0 Members and 2 Guests are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Resonance issues with reedblocks
« on: September 30, 2025, 06:37:05 AM »

This is a topic that has been discussed in length on here before, but I'm bringing it up again in the hope that perchance we shall cover some new ground...

The resonance phenomenon that I am discussing (which I've sometimes referred to as the 'wah-wah' tremolo effect) is when the beating that occurs between two sets of reeds that are tuned apart takes on an unusual or uneven sound; rather than a steady 'wah-wah-wah' of equal measure, you might get a 'waaah-WAH-waaah' for example.  In most cases, a single brace connecting all the reedblocks corrects this immediately.  In my experience, though, if a single brace does not immediately correct the issue, then the problem becomes VERY difficult to completely eliminate.  In these cases, here is what I've done that HAS and HAS NOT worked.

What has NOT worked:

-additional braces across all or some of the reedblocks (and/or every combination thereof)
-tightening/loosening reedblocks and/or ensuring all parts of the reedblock are making contact with the casework
-changing, valves, wax and/or adjusting reed gap
-adding or removing weight to reedblocks

What HAS worked to minimize the issue:

-changing one of the affected reeds with a reed of a different make
-VERY seldomly a second brace has helped reduce the issue if it's occuring in a different part of the block

I have two 3v (MMM) Serenellini instruments that I've experimented heavily with, including making new reedblocks of different configurations.  In each instrument, when using Binci reeds, I've found that there are mild to moderate resonance issues that I've encountered.  These issues ONLY occur in reeds that are on separate blocks facing each other.  For example, the 0 and + reeds are on separate blocks but face each other, whereas the 0 and - reeds are on separate blocks but face away from one another.  With an equal offset tuning (eg -8, 0, +8), the 0 and - reed combo sounds with a 'clean', even tremolo, whereas the 0 and + combo tend to beat a little less evenly.  The difference can be subtle, but it's there, and becomes more noticeable if I increase the bellows pressure - the beating becomes less steady and more 'wonky' or even begins to disappear (and it's not related to increased bellows pressure lowering the pitch of the reed).  I've built several different blocks and the problem persists in each case.  One one set of blocks the problem may be more noticeable in one area, whereas another set of blocks may have the problem one or two notes adjacent.  Even the original blocks show signs of the problem.  I've done everything imaginable to try and mitigate this, and the only thing that has worked so far has been changing either the 0 or + reeds of the affected note with a reed of a different make.

Could reed proximity to one another be part of the issue?  I angled one of the blocks away from the other (easily 15mm or more between the inner-facing reeds), but it hasn't helped.  I'm soliciting input and suggestions, please!
Logged
C#/D player

-Y-

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 896
  • Handry 18 (G/C), Mélodie (D), Club IIb (A/D)
    • a database of nearly 500 melodeons here
Re: Resonance issues with reedblocks
« Reply #1 on: September 30, 2025, 09:18:44 AM »

I'm also interested in any ideas regarding this issue. It has only ever happened to me on relatively high-pitched notes and on instruments that did not present too much tremolo, so that it was simple deal with the thing by tuning the reeds with no tremolo and ease the tremolo of neighbouring notes so as not to feel as an anomaly in tremolo.

What I wonder is if arranging the geometry of the compartment of the reed in question would help? I'd have the intuition that it's one of the factors that influence the vibration that we can act on, but I don't know, I didn't have the chance to try it yet. I imagine that changing the depth with wax is the easiest thing.
« Last Edit: September 30, 2025, 09:23:34 AM by -Y- »
Logged

JNM SY

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 227
Re: Resonance issues with reedblocks
« Reply #2 on: September 30, 2025, 11:41:42 AM »

"I have two 3v (MMM) Serenellini instruments"

 You have probably tried this -  if you put the reed blocks with the problem into a different box ( if they fit),  does the problem persist, or shift to a different note?
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Resonance issues with reedblocks
« Reply #3 on: September 30, 2025, 12:51:56 PM »

"I have two 3v (MMM) Serenellini instruments"

 You have probably tried this -  if you put the reed blocks with the problem into a different box ( if they fit),  does the problem persist, or shift to a different note?
I’ve tried this - the problem persists in the same general area. Sometimes it’s possible to shift the problem area up or down somewhat by removing the brace or making some other adjustments, but it’s still an issue in the same general area.
Logged
C#/D player

Fionn

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 194
Re: Resonance issues with reedblocks
« Reply #4 on: September 30, 2025, 12:53:06 PM »

First thought would be to offset the blocks slightly so the sounding reeds aren't quite in direct opposition...but that might just create a bunch of mechanical issues.
Logged
Vintage Double Ray C#/D

Paul Bryan

  • Member
  • *
  • Offline Offline
  • Posts: 37
Re: Resonance issues with reedblocks
« Reply #5 on: September 30, 2025, 01:46:33 PM »

hi have you tried cutting a panel pin to wedge in between the reed block at the top of the block above or in between the problem reed it also could be the reed tongue needs tightening against the reed plate making sure the tongue is centre in the reed plate
Logged

Aaron Wildman

  • Member
  • *
  • Offline Offline
  • Posts: 36
Re: Resonance issues with reedblocks
« Reply #6 on: September 30, 2025, 03:04:30 PM »

Have you tried any sort of baffle between the reed blocks?  How about stiffening/dampening the Fondo?
Logged

JNM SY

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 227
Re: Resonance issues with reedblocks
« Reply #7 on: September 30, 2025, 03:28:00 PM »

 I see you said changing the wax did not solve it, could adding a screw to tighten the contact to the reed block help?  A lot of my boxes have pins as well as wax holding the reed plates down - just a thought.
Logged

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: Resonance issues with reedblocks
« Reply #8 on: September 30, 2025, 03:37:50 PM »


  Frans van der Aa was of the opinion that the usual straight pieces of metal "brace" across the end of the blocks in larger melodeons gave to Richard a coupling between the reeds. I guess it might depend what reads were in which block.

   The physical process would be analogous to having other resonators, or even pendulums on the same string piece of wood. They tend to end up in unison even if they started slightly apart. We've discussed this several times and not everybody in the group is of the same opinion.

   About 20 years ago he moved away from strict pieces of metal to use pieces of pallet wire with a Z-bend between the blocks. It certainly works and would effectively be like putting a coil into an electrical circuit. Any vibration passing through gets phase shifted backwards.

  So the coupling in fact would be different and to some extent mitigate against read moving into perfect resonance. It's easy enough if you are handy inside melodeon and certainly worth trying.  I would emphasise that I'm coming at this from a theoretical viewpoint, but Frans wasn't still a very practical chap.
Logged
  _       _    _      _ 

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Resonance issues with reedblocks
« Reply #9 on: September 30, 2025, 03:49:29 PM »

First thought would be to offset the blocks slightly so the sounding reeds aren't quite in direct opposition...but that might just create a bunch of mechanical issues.

I did try this, but there isn't really any room to move the blocks laterally.  There would also then be issues of the sound holes between blocks and fondo not quite lining up.  I'm going to see if blocks angled further apart will have any mitigating effect.

hi have you tried cutting a panel pin to wedge in between the reed block at the top of the block above or in between the problem reed it also could be the reed tongue needs tightening against the reed plate making sure the tongue is centre in the reed plate

I should have added "tightening reed rivets" to my list of things that I've tried that have not worked (both with this instrument and with similar situations in the past).  I'm not sure what you mean by 'cutting a panel pin to wedge...' etc?

Have you tried any sort of baffle between the reed blocks?  How about stiffening/dampening the Fondo?

I did, yes.  It did not seem to make a difference.  I'm not sure what you mean about stiffening/dampening the fondo? The fondo is aluminum in both cases.

I see you said changing the wax did not solve it, could adding a screw to tighten the contact to the reed block help?  A lot of my boxes have pins as well as wax holding the reed plates down - just a thought.

The dividers between reed chambers are far too thin to accept a screw or pin.  I suppose I could try at the top of the reedplate.


The frustrating thing with all of this is not being able to understand WHY the issue is occuring.  My understanding in the past was that more rigidity is needed (hence the bracing), but when blocks are laying flat, tightly secured together and against every point of contact with the casework, I'm not sure how much more rigid things can get.  Coming from a design/build perspective, I would like to better understand why the issues are occuring so that I can avoid them when building new blocks and/or eventually event an instrument.  As it is right now, it seems like a bit of a crap-shoot.
Logged
C#/D player

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Resonance issues with reedblocks
« Reply #10 on: September 30, 2025, 03:52:05 PM »


   About 20 years ago he moved away from strict pieces of metal to use pieces of pallet wire with a Z-bend between the blocks. It certainly works and would effectively be like putting a coil into an electrical circuit. Any vibration passing through gets phase shifted backwards.

I recall seeing this on some of Frans' instruments.  I'll have to look into it a bit more and see what I can come up with.  Worth a thought - thanks, Chris.

EDITED TO ADD: if anyone has a photo of Frans' bracing design, please do share!
« Last Edit: September 30, 2025, 03:53:38 PM by mselic »
Logged
C#/D player

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Resonance issues with reedblocks
« Reply #11 on: September 30, 2025, 04:58:33 PM »

So did you manage to isolate the offending reed(s) i.e. block them off to lose the wah wah? You mention swapping reeds as a (partial?) solution. I know this issue has driven you crazy in the past…

Fionn

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 194
Re: Resonance issues with reedblocks
« Reply #12 on: September 30, 2025, 06:23:36 PM »

The frustrating thing with all of this is not being able to understand WHY the issue is occuring.

It must be something to do with the way the sound waves made by those particular bits of metal, tuned at that particular pitch, move or behave in relation to one another. The issue disappears if you swap one of them out for a slightly different type of metal tuned to the same pitch, and it doesn't even occur if they're not in opposition.

It might be roughly comparable to getting a wolf on a cello or viola. Not the same phenomenon (there the vibration is interacting with the wooden body), but the same sort of physics.
Logged
Vintage Double Ray C#/D

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Resonance issues with reedblocks
« Reply #13 on: September 30, 2025, 06:36:41 PM »

So did you manage to isolate the offending reed(s) i.e. block them off to lose the wah wah? You mention swapping reeds as a (partial?) solution. I know this issue has driven you crazy in the past…

Three adjacent buttons were affected (D/E, F#/G, A/B) with the 0 and + reed combo, and I managed to mostly eliminate the issue by replacing at least one of the Binci reedplates in each pair.  In one case I actually had to replace both Binci reeds with those of a different make.  The 0 and - reed combo did not suffer from the issue at any point.  It works but it's not ideal as Bincis tend to have a very particular quality and tone to them, and swapping them out with something else can be noticeable.  I did my best to use reeds that were of a similar scale length and with similar tonal qualities as Binci but, funnily enough, the more alike the reeds were, the more likely it was that the problem would continue;  the issue most easily disappeared when I used reeds that were noticeably different from Binci.  Four reedplates (out of 33 total for the D row) needed to be changed.

Any time I've had issues with this on a box with a D row, it's almost always been one of the same three buttons affected (corresponding to notes D/E, F#/G, A/B).  It's not always both the push and pull for each button that's affected either - sometimes it's just one direction that is a problem.

Also, I say 'mostly' eliminated as there is still a bit of a different quality to the beating when using the stops to compare "0 and +" with "0 and -" for the same note. The beating is the same in both cases, and generally stays constant regardless of bellows pressure, but comparing them side-by-side I can tell that they are behaving just a *little* differently.  Would anyone else notice? Possibly not.  I'm cursed with a *very* sensitive ear...the current fix is satisfactory in order to be playing the instrument, but I'd prefer to be able to keep the same make of reed throughout the instrument to maintain a consistent tone.  That, and I'd really like to better understand why the issue is occuring in the first place so that I can take steps to avoid it when building blocks in future.
« Last Edit: September 30, 2025, 06:39:33 PM by mselic »
Logged
C#/D player

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Resonance issues with reedblocks
« Reply #14 on: September 30, 2025, 08:04:40 PM »

Interesting. I'd probably conclude the reeds are faulty or somehow not compatible with the instrument and move on, esp if swapping them out fixes the problem. You probably don’t have the luxury of being able to fit some similar Binci reeds to see if the problem goes away. In my experience most people cannot hear the difference (although I can hear), and in particular professional musicians tend to put up with all sorts of nonsense and not notice (I am not making this up…it really is true).
I might (though maybe I would not) take the offending reeds and try to get them to misbehave somewhere else.
Binci reeds are great for Morris, coz they are so f** loud. Will anyone actually notice the wah wah outside? And inside they are horribly anti social.

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: Resonance issues with reedblocks
« Reply #15 on: September 30, 2025, 10:35:33 PM »



  I have Binci's.  they are absolutely fine when played loud but I think the test of a really good reed is how quietly you can play it?
Logged
  _       _    _      _ 

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Resonance issues with reedblocks
« Reply #16 on: October 01, 2025, 04:42:11 AM »

It's worth mentioning that the other Serenellini also had a few resonance issues when using Binci reeds, but that there was no issue when I used a full set of VA TAM reeds instead.  It would seem that the Bincis might be more susceptible or prone to this for some reason, although I've only the one set that I own and have worked with, so couldn't say for sure.  I recall that a Gaillard box with Bincis suffered similar problems that several pro fettlers tried to fix but were unable to eliminate completely.

Regarding the tone of Bincis, it's amazing the difference that reedblock design makes.  I started a different thread on that topic a while ago so I won't get into it here, but reducing the depth of the reedblock chambers had a very pronounced effect of softening and sweetening of the tone of the Binci reeds (and any other reed) when used in these two Serenellini boxes.
Logged
C#/D player

Fionn

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 194
Re: Resonance issues with reedblocks
« Reply #17 on: October 01, 2025, 08:21:00 AM »

Wonder if it might be worth asking Binci about it?
Logged
Vintage Double Ray C#/D

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Resonance issues with reedblocks
« Reply #18 on: October 01, 2025, 09:04:37 AM »

It's worth mentioning that the other Serenellini also had a few resonance issues when using Binci reeds, but that there was no issue when I used a full set of VA TAM reeds instead.  It would seem that the Bincis might be more susceptible or prone to this


Maybe it’s a problem related to a combination of reed design and reed block design? You’ve also observed that reed block design can have a big effect on timbre.  That suggests that the reed block is acting as a filter and is reducing some frequencies.  I have tuned a large number of Emmanuel Pariselle’s boxes, most of which have Bincis, and I don’t recall any resonance problems that were not fixed by a brace across the blocks.

Also I’ve recently read the VA website about their Blue Star reeds which they say need to have a suitable reed block design to perform at their best.



Here is a quote from VA

Quote
To ensure the full expression of the the very high acoustic potential of the reeds, the accordion must be provided with the right conditions, starting from the correct adaptation of the reed block airflow to the reeds.
« Last Edit: October 01, 2025, 09:10:51 AM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Resonance issues with reedblocks
« Reply #19 on: October 01, 2025, 09:22:45 AM »

Here is a further quote from VA about their reeds that emphasises the importance of reed block design:
Quote
Reeds and reed block are an inseparable binomial for ensuring sound quality: only if the ideal air dynamics inside the cells of the reed block are precisely identified and achieved can the full sound potential of the reeds be extracted. In practical terms, this means regulating the air flow, pressure and speed: it is a crucial aspect because air is the element which makes the reeds work and is decisive for their performance. To use a metaphor, the reed and reed block combined are the engine of the instrument, the air is the fuel: the reed block regulates the fuel supply.
Thus, in order for our reeds to express their full acoustic potential in the terms outlined above, the reed block must be designed and built to suit the reeds: the volume and shapes of the cells must be adjusted according to a certain criterion, to achieve the optimum air circulation, air pressure and airflow conditions.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1] 2 3 4 5   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal