Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 3 4 [5]   Go Down

Author Topic: Resonance issues with reedblocks  (Read 6943 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Resonance issues with reedblocks
« Reply #80 on: October 26, 2025, 08:43:33 PM »

Quote
If this is happening on several reeds (or lots of them) the coupling is probably acoustic, if it's only happening on one or a few it's more likely to be mechanical. Which is it?

The issue generally affects several adjacent reeds (three or so adjacent buttons).  As I made several different blocks (different chamber sizes/desgin, all hardwood or hard/softwood, etc), the issue would be less apparent on some blocks and more on others, but always present to some degree.  The drier the tuning, the more obvious the phenomenon.  In one case, one of the notes higher up the scale was also mildly affected.

One thing I noticed in general about 3v MMM boxes that I have - if one pushes quite hard while playing a note (harder than one would under normal playing circumstances), the MM set that is facing each other will tend to want to lock together in unison, whereas the MM set that are on separate blocks and facing away from each other never will, regardless of how hard the bellow are pushed (this is noticed when you are able to isolate two banks at a time with stops, for example).  It's not an issue because I wouldn't normally push that hard, I'm only mentioning it as an acknowledgement that there is a acoustic/mechanical phenomenon happening with the reeds facing each other that does not occur on those facing apart on separate blocks.

A question related to the posts above: what does it mean to say a set of reeds is tuned +5 ?
Is a specific reference note tuned 5 cents sharp?
Or should I just interpret this as a rough indication of the wetness of the tuning?

Regarding cents vs Hz...for tuning work that I do, I use cents offset as my reference as it makes the most sense (haha) to me. I understand why others may wish to use Hz.  A tuning on a 2v box described as having a +10 cents offset would mean one set of reeds is tuned to a 0 reference point (such as A=440Hz), and the other set of reeds to an AVERAGE of +10 cents sharp of the 0 reference point.  By average I mean I will tune the second set of reeds using +10 cents as my guideline, increasing the offset on the lower notes and decreasing the offset on the higher notes to what sounds good to my ear (although by this point I generally know how what that translates to directly in cents).  With drier tunings, such as +5, there is very little difference in cent offset from the highest to the lowest notes as the beating is generally exactly where I like it.  On wetter tunings, a constant cent offset would result in the beating being far too fast on the highest notes and possibly not enough on the lowest notes.

Forgive me if I missed this somewhere.  Is it possible that the problem lies with the receiver rather than the transmitter?  Perhaps something quirky with your ear (hyper sensitivity or something more obscure?) that creates what you are perceiving? Some sort of aural fixation or hypersensitivity or some other obscure cause?

Have you used any software to record and analyze?  Have you got any other pairs of ears to confirm your findings (getting a bigger sample size etc)? 

You did say something about having sensitive hearing, so I thought approaching that from multiple angles may provide additional information about the resonance problem, or absence of, or perhaps clarify its severity.



This issue isn't with my ears   ;)  Regarding sensitivities, I know some people that can play a musical instrument that is clearly out of tune and think it sounds fine, and others that will notice when a note is off by just a few cents...
Logged
C#/D player

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Resonance issues with reedblocks
« Reply #81 on: November 18, 2025, 05:40:37 AM »

I must be cursed.  I've encountered the problem again in a 2v box I recently picked up.  One of the pull notes is affected and none of the usual tricks (including changing reeds) seems to help.  By moving around the brace(s) the best I can get is to have the two reeds lock together in unison, with an occasional beat that doesn't quite sound right.  The strange thing is, the problem only occurs once the box has been reassembled and ALL six of the bellows pins are back in place.  With the treble end just resting on either it's own bellows or a set of tuning bellows, the problem is gone. Once the pins go in and things get airtight, the problem pops up.  I don't get it...
Logged
C#/D player

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Resonance issues with reedblocks
« Reply #82 on: November 18, 2025, 08:24:23 AM »

I'll echo what was said above about being a perfectionist.

As a guitar maker I've spent countless (unpaid) hours making sure my guitars didn't have wolf notes. I had a customer come over with his £6.5k instrument to try out one of my builds, and the first thing that jumped out at me was an incredibly overpowering, soul-destroying, head splitting wolf on his guitar. If I built anything with such a bad wolf, there is no way I'd consider selling it until it was mitigated.
When I very politely and cautiously pointed at the wolf, the chap said "well, it's a hand-made guitar - a lot of them have a bit of a character you have to work around".

Box players might not notice these small resonances at all.
Logged

-Y-

  • Hero Member
  • *****
  • Online Online
  • Posts: 896
  • Handry 18 (G/C), Mélodie (D), Club IIb (A/D)
    • a database of nearly 500 melodeons here
Re: Resonance issues with reedblocks
« Reply #83 on: November 18, 2025, 08:16:56 PM »

Wanting to remove a perfectly audible flaw (that can prevent you from establishing a proper tremolo curve) is not perfectionnism, it's just professional behaviour.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Resonance issues with reedblocks
« Reply #84 on: November 18, 2025, 09:39:18 PM »

I think I may have at last made some progress...the small, wooden cocktail stick stuck between the block and the corner of the casework seems to have cleared up the issue.  It looks like a mess in there right now, but this combination of braces and cocktail stick seems to have done the trick (fingers crossed).  Connecting the side of the block to the casework is the only thing that eliminated the problem in the middle of the keyboard.  I recall doing this once before for an old Paolo box.  I'll probably devise a more permanent solution, but the fact that this is working is a godsend right now...

While the issue may not have been immediately apparent during fast playing, it certainly stood out when playing anything slower with sustained notes so I don't think it was a case of perfectionism trying to sort it out.
« Last Edit: November 18, 2025, 09:55:15 PM by mselic »
Logged
C#/D player

odonovanchris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 276
    • Instagram Accordion Profile: chris0donovan
Re: Resonance issues with reedblocks
« Reply #85 on: November 19, 2025, 04:08:19 AM »

Are the blocks and fondo completely flat? My spidey sense says there might be some warping if supporting the block in the center with the stick like that solves the problem. Not sure if this was previously discussed
Logged
See my accordion projects on Instagram: https://www.instagram.com/chris0donovan/

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Resonance issues with reedblocks
« Reply #86 on: November 19, 2025, 05:38:08 AM »

Are the blocks and fondo completely flat? My spidey sense says there might be some warping if supporting the block in the center with the stick like that solves the problem. Not sure if this was previously discussed

I checked that using a straight edge. Both blocks and fondo are perfectly flat.

I’m happy to report the problem is gone. The few braces and stick seemed to work.
Logged
C#/D player

IanD

  • Hero Member
  • *****
  • Online Online
  • Posts: 1703
  • Too many melodeons...
Re: Resonance issues with reedblocks
« Reply #87 on: November 22, 2025, 02:35:27 PM »

Are the blocks and fondo completely flat? My spidey sense says there might be some warping if supporting the block in the center with the stick like that solves the problem. Not sure if this was previously discussed

With any mechanical resonance like this, there's not necessarily anything "wrong" except bad luck, it just happens to coincide with the frequency of a reed and is excited by it.

Without knowing the exact cause of the resonance, almost any change (like a brace, or a toothpick, or adding the bellows...) can move the frequency or damp it enough so that it's no longer a problem -- or move the problem to another note, or have absolutely no effect... :-(

Sounds like black magic but that's how resonances work -- "wolf notes" in stringed instruments which are the same problem, see above post...
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

JNM SY

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 227
Re: Resonance issues with reedblocks
« Reply #88 on: November 22, 2025, 05:07:47 PM »

It's fixed now so thats great - but if the stick works loose and / or the fault should come back -
 I noticed from the picture, if you zoom in on the high end
R/H side of the reedblock, there is a definite space between the wooden guide block and the reedblock.
There is also a small (1mm) space between the reedblocks in the middle which leaves the possibility of them working loose. I would fit a new strip of wood along the full length of the outside of the reedblocks leaving no space for them to be loose even before the top clamp is tightened up. - I hate loose blocks and often add a shim on the front lip of the block so they are nice and tight there as well.   
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Resonance issues with reedblocks
« Reply #89 on: November 22, 2025, 08:49:02 PM »

Black magic indeed, Chris...I understand there is a reason an issue like this is occurring, but without being able to pinpoint exactly what the cause is, it becomes a very frustrating case of chasing down problems by trying an infinite number of solutions (or combination of solutions).

I've since discovered one of the notes on the outside row is now affected. Funnily enough, the issue seems to have shifted from one note to the next at one point without me having changed or adjusted a single thing.  Since the note that's currently affected is on the C# row and is only ever used as a very brief, passing note occasionally, I've just been playing the thing as is and will look at revisiting solutions again in a little while.

JNM SY - the spaces you're describing have all been 'blocked'-up at various points in the troubleshooting process with no impact on the issue.  Everything is pretty darn snug right now, and tied to itself at multiple points (I've since added additional bracing between the blocks and the casework), so there's no real possibility of the blocks working loose or even shifting.  There's just nowhere for them to go.
« Last Edit: November 23, 2025, 12:56:05 AM by mselic »
Logged
C#/D player
Pages: 1 2 3 4 [5]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal