Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: wanted: advice on muting bass voices and tuning the smallest reeds  (Read 988 times)

0 Members and 1 Guest are viewing this topic.

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA

I’ve been busy tuning a cba button accordion and a Hohner club III.
Some actions I found hard to do: tuning the highest sounding reeds, and isolating bass voices.
The high reeds are positioned upside down; is there any way of tuning them in the instrument? What I did was take the reed block out, tune, put block back in, check, repeat, repeat, repeat. I could have measured offset and tune the block outside the instrument, but maybe there’s another way?

In the cba, the lowest two octaves are in non-removable blocks. I tried muting the reeds by wrapping cling foil around them, but I didn’t find that very practical. Do you have any tips?
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: wanted: advice on muting bass voices and tuning the smallest reeds
« Reply #1 on: November 13, 2025, 06:45:21 AM »

For small reeds (in a PA or CBA…I tune a lot of PAs) I measure the offset and tweak outside the box. You will also find that if the rest of the block is tuned correctly (in the box) the little reeds can be tuned relative to these other reeds, out of the box. Also, if you have the concert reed set correctly you can set the tremolo reed relative to this outside the box…this pretty much always works for me and can take the heat out of tuning the high reeds (as a practice I always start at the top end because they are so tricky….the rest of it is easy).
It's not fool proof but it mostly works for me. However, having said all of that…if the blocks have an unhelpful arrangement then..yes it's in, out, in, out and v tedious.
Little reeds are probably the hardest to tune without messing them up. Piccolo reeds are by far the most difficult. I never put a file anywhere near them, Using a scraper, even to sharpen, is how I do it. You only need to breathe on them. I also have a tiny little battery engraver pen which is v good for flattening, where scraping can mess up the voicing…..but it has to be used very carefully (it's not a Dremel).
Tuning bass reeds (on a big instrument) is probably the next most difficult thing because you really have to tune them in situ (esp if the blocks are glued in…). I use masking tape on the ones I want to silence (which means muting several) …place across the reed and valve. Use tweezers to pull off to avoid damaging the valves. Tune by octave. This is also where Dirks Tuner is very handy if I want to find an errant note within an octave stack.
« Last Edit: November 13, 2025, 06:52:17 AM by Rog »
Logged

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
Re: wanted: advice on muting bass voices and tuning the smallest reeds
« Reply #2 on: November 13, 2025, 09:44:07 AM »

Rog, thanks for the tips! Especially about tuning relative with the block out of the box.
What I sometimes use for very small reeds is fine grain sandpaper glued onto a tiny flat stick. I may have this trick from Thierry Benetoux.
The masking tape I don’t get; do you actually tape over the valves? I don’t think I would dare to do that. Mostly I stick a piece of paper behind the outer reed also covering the valve next to it, but often this will not completely silence the inner reed.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: wanted: advice on muting bass voices and tuning the smallest reeds
« Reply #3 on: November 13, 2025, 01:55:35 PM »

Yes just tape over the valve and adjacent reed (one reed plate at a time….I tune an octave stack, I don't tape the entire block, just two or three reed plates at a time).
Yes I tried Benetoux's fine sandpaper on a block but could never get it to work. I have a variety of scrapers (the end of one of those cheap needle files is in fact as good as anything). For really tiny reeds the scraper works for both flattening and sharpening. If the reed is upside down you can support it with the blade of a feeler gauge. I have a miniscule bit for the pencil engraver and this works pretty well too (essentially it's a fast revolving diamond file).
« Last Edit: November 13, 2025, 01:59:05 PM by Rog »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: wanted: advice on muting bass voices and tuning the smallest reeds
« Reply #4 on: November 13, 2025, 02:41:53 PM »

My method for the highest reeds is to tune them outside the box to be very slightly sharp, then in the box use the scratcher to flatten the pitch to the correct value.  I find that almost all reversed reeds can be reached with a scratcher.  For the occasional ones that are out of reach I have a curved scratcher made from an old needle file.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
Re: wanted: advice on muting bass voices and tuning the smallest reeds
« Reply #5 on: November 14, 2025, 10:11:01 AM »

Rog, thanks for the additional tips. Although I’m wary of using a mechanical tool on tiny reeds. My glass engraver has a tip of 1mm but it rotates so fast that even a light fast touch may result in too much material removed.
And Theo also thanks, this seems like a clever approach, because it’s much easier to scratch the small reeds than to file at the top. I’ll definitely try that.
How do you mute bass reeds, or entire bass voices in blocks that can’t be taken out of the instrument?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: wanted: advice on muting bass voices and tuning the smallest reeds
« Reply #6 on: November 14, 2025, 10:16:44 AM »

If I want to mute a whole bank or reeds on a glued in block I just lay a strip of masking tape over the whole line of reeds. Remove by pulling upwards so you don’t lift the valves. I would be wary of doing that if the valve and glue are old.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
Re: wanted: advice on muting bass voices and tuning the smallest reeds
« Reply #7 on: November 17, 2025, 08:59:02 AM »

Theo, what kind of masking tape? I can see myself pulling apart multiple valves when removing it...
The masking tape I know is pretty sticky.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: wanted: advice on muting bass voices and tuning the smallest reeds
« Reply #8 on: November 17, 2025, 09:04:43 AM »

Just standard masking tape from a stationery shop.
I’ll add this to my list of future video topics.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: wanted: advice on muting bass voices and tuning the smallest reeds
« Reply #9 on: November 18, 2025, 07:36:32 AM »

You can get 'low tack' masking tape, used by decorators. Also, artist tape (more expensive). I use the low tack stuff. I never have issues removing it. Pull upwards in the direction of the valve, use tweezers. Muting individual reeds gives me more control than a whole bank, but we are talking big owd accordion basses rather than melodeon reeds. Anyway, that's how I do it.
« Last Edit: November 18, 2025, 07:39:55 AM by Rog »
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: wanted: advice on muting bass voices and tuning the smallest reeds
« Reply #10 on: November 18, 2025, 08:16:43 AM »

I also use low tack (frog tape). Somebody on this forum suggested using Scotch Magic tape.

The only word of warning is that if you forget and leave the low-tack one on for a couple years, it becomes incredibly difficult to remove, just like any other old masking tape.
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: wanted: advice on muting bass voices and tuning the smallest reeds
« Reply #11 on: November 18, 2025, 09:28:52 AM »

Scotch magic tape works perfectly.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal