Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Thud when pallet hits faceplate  (Read 745 times)

0 Members and 1 Guest are viewing this topic.

kenakordeon

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 264
Thud when pallet hits faceplate
« on: January 22, 2026, 07:19:28 PM »

This is a 4-voice, single row, Cajun-style box. When I bought it 12 years ago it was silent when the buttons were released and the pallets closed onto the wooden treble faceplate. Over the past few years I hear a more definite soft "thud" or "plop" when the pallets contact the faceplate. On each pallet there is a length of red felt and then attached to that, and the contact point, is a very thin piece of, I think, chamois.  Question is where can I buy that chamois/fabric?

I'm in the US.

Thanks for any help.

Ken
Logged

kenakordeon

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 264
Re: Thud when pallet hits faceplate
« Reply #2 on: January 23, 2026, 02:44:50 PM »

Thanks doe your help.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Thud when pallet hits faceplate
« Reply #3 on: January 24, 2026, 04:26:51 AM »

You may already know this, but just in case you don't..if you glue a new strip of chamois to the facing on your pallets you may find it alters the geometry..causing an air leak. It will lift one end more than the other, relative to the lever and its pivot point. You can draw a diagram to show this. It is more pronounced on instruments with long pallets, like yours. I'm not saying this will happen, but it might. Try one pallet at a time to check. Normally when refacing pallets you have to reset them so they lay flat on the fondo and the lever arm is raised (or lowered)slightly because of the new facing. On some Cajun boxes the pallets are screwed on…which means you cannot easily do this (and it's a job I refuse on some instruments because it is a difficult/risky job and more trouble than it is worth, if the pallets are screwed in place rather than glued).
« Last Edit: January 24, 2026, 04:29:06 AM by Rog »
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Thud when pallet hits faceplate
« Reply #4 on: January 24, 2026, 04:53:27 AM »

Yes, as Roger said, you have to re-seat the pallets if replacing with new felt/leather. With Cajun boxes that have screwed-in pallet/lever connections, it can be a right pain. Your best bet would be to replace with the exact same thickness of material that was there before, but even then it may not be perfect and the pallets might leak. It’s a piece of cake on any box with glued-in or waxed-in levers, but it can be a nightmare on Cajun boxes…
Logged
C#/D player

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Thud when pallet hits faceplate
« Reply #5 on: January 24, 2026, 04:57:20 AM »

Yes, as Roger said, you have to re-seat the pallets if replacing with new felt/leather. With Cajun boxes that have screwed-in pallet/lever connections, it can be a right pain. Your best bet would be to replace with the exact same thickness of material that was there before, but even then it may not be perfect and the pallets might leak. It’s a piece of cake on any box with glued-in or waxed-in levers, but it can be a nightmare on Cajun boxes…
Haha. I didn't want to call it that..but exactly. When faced with a £4k genuine Cajun box with this clacky issue I just decline…far too risky. And when I asked Rees (Wesson) about the technique, he said something like..'it's very difficult'.
« Last Edit: January 24, 2026, 04:59:13 AM by Rog »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Thud when pallet hits faceplate
« Reply #6 on: January 24, 2026, 08:59:26 AM »

A simple fix that might work is to scuff the pallet face with a finite brush.  This raises the map on the leather. It’s not a complete fix and may  not last but it won’t alter the thickness of the pads enough to change the geometry.  You can get access to the pads by removing the whole keyboard rather than detaching the pallet from the levers.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Squeezebox Of Delights

  • Good talker
  • **
  • Offline Offline
  • Posts: 81
Re: Thud when pallet hits faceplate
« Reply #7 on: January 24, 2026, 12:56:08 PM »

A simple fix that might work is to scuff the pallet face with a finite brush.
Make sure you don't use an infinite brush though, or you'll be doing it forever  ;)
Logged
Oops! All Hohners

kenakordeon

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 264
Re: Thud when pallet hits faceplate
« Reply #8 on: January 25, 2026, 03:21:25 PM »

Thanks again to all for your advice and warnings and suggestions. I will start by using a fine brush to raise the nap on the leather. The measurement, as close as I could get it with a digital caliper, of the underlying red felt is slightly shy of 4mm. I am guessing that this felt is sold in full millimeter thicknesses so I will assume the original thickness was 4mm. I will order the 4mm from Bossetto Accordions on ebay to have available in case the raising of the nap doesn't solve the issue of the pallet thud. I do think that over the period of time which I have owned and more-or-less regularly played this accordion that the 4 mm felt has compressed and become more dense which would then create a "harder" sound when it is released against the treble faceplate. That thud is never heard in a session when all four reed banks are open but only when I am  playing in smaller groups or solo.

Anyway, just thinking out loud here.  Thanks again for your help.

Ken
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal