Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3   Go Down

Author Topic: Restoring Pre-War Hohner Club II  (Read 17841 times)

0 Members and 1 Guest are viewing this topic.

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Restoring Pre-War Hohner Club II
« on: December 27, 2009, 06:57:56 PM »

So I took delivery of the Club II that I got on Fleabay.  I have posted some Pix.  I'm of a mind to Restore this box.  It is in very nice condition with some exceptions.  Those are the following:

1.  The box looks to have been stored in a Dry place and been exposed to some heat.  It came from Utah a desert state.  The Celluloid has shrunk and has become warped and detached from the plywood of the box.  The celluloid is otherwise in very nice condition.  Not sure if this is restorable or should I just strip the celluloid off?

2.  The box mechanisms seem to be in outstanding condition.  The Button mechanisms work smoothly and the action is nice, no serious rust or corrosion that I can detect.  However I believe the reeds need to be re-waxed and tuned, When the bellows are pushed or pulled 3-4 of them sound, this could be stuck valves, some of the leather valves have dropped off due to the extreme drying of the glue holding them in.  

The box is in C/F and it is completely original, the original owner must have played it but it's straps are nearly pristine and aside from the lack of care in storing the box it obviously was at one time played and loved as it does have some original wear,not much though.  I looked for a serial number but being a novice at this kind of thing I'm not sure as to where to look for a serial number.  I did find a mark on the treble side of the box and the same mark on the bass side on the inside of the box.  I have enclosed pix of that mark.  Not sure what this mark is possibly a factory mark of some kind it looks like personal initials stamped though.  

Any advice as to what I should do with the celluloid would be helpful.  I'm thinking this box is well worth restoring.  Any and all advice and ideas would be appreciated.  

--Drew

Here is the link to the remaining photos:

http://s815.photobucket.com/albums/zz72/ajay38/ClubII-restoration/
« Last Edit: December 27, 2009, 07:14:43 PM by ajay38 »
Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Restoring Pre-War Hohner Club II
« Reply #1 on: December 27, 2009, 07:30:19 PM »

1. Celluloid goes soft with the application of acetone so you might be able to apply some and then reshape/stretch. That would be my first port of call as once you remove it, its off, where as if it doesn't reshape well you can then take it off afterward.

2. If 3 or 4 reeds sound at once its most likely to be treble pallets letting air into more than one reed chamber. Check the pallets under the treble grill are firmly closing the hole, you might need to reface them with felt and leather. It's probably worth revalving, waxing and tuning anyway just to get the best out of it. Limit the treble action as well whilst your at it.
Logged

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Re: Restoring Pre-War Hohner Club II
« Reply #2 on: December 27, 2009, 07:54:06 PM »

1. Celluloid goes soft with the application of acetone so you might be able to apply some and then reshape/stretch. That would be my first port of call as once you remove it, its off, where as if it doesn't reshape well you can then take it off afterward.

2. If 3 or 4 reeds sound at once its most likely to be treble pallets letting air into more than one reed chamber. Check the pallets under the treble grill are firmly closing the hole, you might need to reface them with felt and leather. It's probably worth revalving, waxing and tuning anyway just to get the best out of it. Limit the treble action as well whilst your at it.

Should the acetone be applied directly to the celluloid while it's on the box? If so should I just use a brush to apply the acetone onto the celluloid then stretch it and fit it back to the box?  Once applied does the acetone just soften the celluloid thus allowing one to manipulate it as needed?  Also would this dull the sheen of the celluloid once it's manipulated back into shape?
Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Restoring Pre-War Hohner Club II
« Reply #3 on: December 27, 2009, 08:16:39 PM »

I would try it with the celuloide on the box and applying directly. I've not tried it myself on melodeons but have elsewhere - I see no reason why it wouldn't react the same. Any dull areas can just be buffed up. See http://forum.melodeon.net/index.php?topic=485.0.
Logged

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Re: Restoring Pre-War Hohner Club II
« Reply #4 on: December 27, 2009, 10:14:14 PM »

Well my attempt at applying acetone seemed to dissolve the Celluloid as opposed to just softening it.  I immediately had to Peel off the Celluloid that I attempted to soften and stretch.  This in turn turned into a celluloid stripping excercise, most of the Celluloid came free quite easily even without the application of aceton, except for the bit around the Bass buttons which I cut off using an exacto blade.  Now I have a presswood Club II.  I really didn't want to remove that celluloid but it really had shrunk a great deal and was coming off in whole slabs anyway. 

I took out the Reed Blocks, and those will probably go to the tuner for total redoing.  Not sure if I want to "declub" this box since I really don't know what that means (more research to do).  I found that the treble and bass Pallets are leaking due to old seals so those will need replacing (more research).  As for the  bellows they are practically perfect except for age, the tape looks good and the bellows corner clamps ( Not sure what those metal brackets are called) just need a bit of touching up with steel wool.   I will also have to sand smooth the now bare presswood and stain it.  Any ideas about what I should use to do this part of the project would be very helpful.  Probably a light to medium stain and then an application of varnish of some kind. 
Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

Steve C.

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2075
  • Erica, Morse Anglo
Re: Restoring Pre-War Hohner Club II
« Reply #5 on: December 27, 2009, 10:24:27 PM »

With respect, always get a second opinion about any major repairs.  If you have ever seen celluloid/acetone application (new manufacturing) you would know that what you did would be suicide.
Logged
Located in Central North Carolina, USA; credit for picture: livingplanet.ca

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Restoring Pre-War Hohner Club II
« Reply #6 on: December 27, 2009, 11:00:52 PM »

I did say I've never tried it on melodeons! - sorry to hear it didn't work out. The club button is called a gleichon (spelling?) and its the key with hashing on it on the F row. Basically it plays the same same note either way giving your more fingering options. De-clubbing just involves tuning it to the expected note for on the row playing.

You can make your own pallet facing by gluing a layer of felt to a layer of fine suede leather. The felt dampens the clacking and the suede provides an air proof seal. Take the white muslin dots off of the tops of the pallets and then gently ease the wooden pallets off. If they are waxed on or the glue is brittle you can normally just prise them off. If they are well and truly stuck you'll need to take the whole mechanism off and soak the pallet and the ends of the leavers in warm water to relax the glue.

Once off you can then soak the pallets in warm water to get the existing material off (or just pull it if it is loose). Dry and sand flat, then stick to new felt/leather layers. Once they are dry you can cut around them to get them off. I quite like waxing the pallets back on with reed wax as it allows for adjustments later on.

It's also worth removing the old rope seal around the bellows frame and replacing with a self adhesive neoprene strip.

For re-vanishing I found a pretty good match for the Hohner Erika red - a deep red stain and a slightly yellow tinted varnish provides a good finish. The next time I have to re-varnish I'm going to try the Cajun style finishing of using coloured ink under a clear varnish to try and get a blue/aquamarnie colour similar to the one Saltarelle use. If the grain of the wood isn't that interesting then a good colour could really make the box stand out.
Logged

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Re: Restoring Pre-War Hohner Club II
« Reply #7 on: December 27, 2009, 11:17:03 PM »

With respect, always get a second opinion about any major repairs.  If you have ever seen celluloid/acetone application (new manufacturing) you would know that what you did would be suicide.

I was thinking that I should have got a second opinion but I was impatient and I also figured that as much shrinkage and debonding (not sure that is a word) that had occurred was not fixable or would take too much time and effort.  I've been wanting to strip one of these boxes anyway and this one seemed ideal since the Celluloid was already practically peeling off.  It took very little effort to remove it.  So now I will attempt to restore it but without celluloid.  No harm was done, as I think the Celluloid had to come off anyway.  The Plywood underneath the celluloid is in good condition.  

So next Question is where to get Reed wax?  Also I'm assuming that the felt and the Suede needs to be quite fine and thin for this use?
« Last Edit: December 27, 2009, 11:34:38 PM by ajay38 »
Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

old geezer

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 241
  • Hohner Melodeon
Re: Restoring Pre-War Hohner Club II
« Reply #8 on: December 28, 2009, 02:49:08 AM »

another celluloid suicide moment
Logged
Jack Murphy    beyond the black stump

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Restoring Pre-War Hohner Club II
« Reply #9 on: December 28, 2009, 09:47:48 AM »

To soften celluloid to enable re shaping you must never use net acetone.  As you discovered this will simply disslove the celluloid.  The acetone must be diluted with water first.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Restoring Pre-War Hohner Club II
« Reply #10 on: December 28, 2009, 12:13:47 PM »

I used some acetone based nail varnish remover - it must have been pre-diluted.  :-\
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Restoring Pre-War Hohner Club II
« Reply #11 on: December 28, 2009, 05:03:22 PM »

I used some acetone based nail varnish remover - it must have been pre-diluted.  :-\

Perhaps it would have been wise to give the full details in your original advice?

If they are well and truly stuck you'll need to take the whole mechanism off and soak the pallet and the ends of the leavers in warm water to relax the glue.

Once off you can then soak the pallets in warm water to get the existing material off (or just pull it if it is loose). Dry and sand flat, then stick to new felt/leather layers. Once they are dry you can cut around them to get them off. I quite like waxing the pallets back on with reed wax as it allows for adjustments later on.

I  think that soaking the pallets in water is a pretty bad thing to do (though not as bad as using neat acetone on celluloid :(), and quite unnecessary.  The pallets on pre-war Hohners usually come of very easily, I've renovated dozens of them and never needed to use water,  sometimes if the steel is badly rusted they can be a tight fit, in those cases I find that a hot soldering iron applied to the lever end for half a minute or so usually frees things enough.  To remove the pallet facings, just ease a blade under a corner and pull the leather off, then scrape and sand off what remains, leaving a smooth surface for the new material.  And don't forget to clean out the slot in the pallet where the lever fits.

Another good way of fixing the pallets back on is to fit all the pallets in place, then apply a small dollop of hot-melt glue to the top of each pallet.  This is easy to peel of at a later date, but if you do the job right you should not need to make any adjustments later on.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Restoring Pre-War Hohner Club II
« Reply #12 on: December 28, 2009, 07:16:40 PM »

I've not had pallets expand from adding water which is always a concern when water is involved. I've found it helpful in getting newer glues off without sheering bits of wood from the pallets.

Completely agree with giving full advice - I didn't realise myself about the diluted acetone and would never have recommended it otherwise!  :-[ :-X :-\ :'( :-*
Logged

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Re: Restoring Pre-War Hohner Club II
« Reply #13 on: December 28, 2009, 08:30:09 PM »

I hold no one to blame but myself as far as the Acetone disaster goes.  So no apologies necessary, I think the cellulose came off rather nicely and I'm going to try something new and different.  What that is I'm not sure but the experiment continues.  The reed blocks are going to be refurbished and tuned by Theo and I'm thinking of going dry on the tuning.  ALthough some might think that is a waste on a Club box.  I'm also not going with the de-clubbing as I'm a relatively new player so I figure the club system might turn out to be something that I can try out!  Next is the Pallets I have to figure out where to get the Felt and leather for those!
Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

michik

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 412
Re: Restoring Pre-War Hohner Club II
« Reply #14 on: December 28, 2009, 08:39:38 PM »

What about covering the naked melodon with something like that  ;D
https://secure.aspects-supplies.co.uk/products/showproduct/470
Logged
Michael Knapp ~ Vienna ~ Austria
Playing on "Parigi Giovani" G/C (made by Bompezzo) - My recordings: http://www.onmvoice.com/mknapp

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Restoring Pre-War Hohner Club II
« Reply #15 on: December 28, 2009, 08:42:09 PM »

and I'm thinking of going dry on the tuning.  ALthough some might think that is a waste on a Club box. 
Waste not, whatnot!

I have an old Double Ray in Bb/Eb that I have seriously dry tuned, zero zero throughout, no thirds. It doesn't sound like a Hohner for sure but I'm using it more and more these days, especially in my new Welsh band, Parti Gungrog, where its hard grinding dryness sits Druidically against the the softness of the mountain flute and the punky funky reggae ukelele.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Restoring Pre-War Hohner Club II
« Reply #16 on: December 28, 2009, 08:42:57 PM »

Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

waldoB

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 126
Re: Restoring Pre-War Hohner Club II
« Reply #17 on: December 28, 2009, 08:43:26 PM »

cgmmusical dot co dot uk will oblige very reasonably with self adhesive felt/leather pallet facing
Logged

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Re: Restoring Pre-War Hohner Club II
« Reply #18 on: December 28, 2009, 09:20:50 PM »

What about covering the naked melodon with something like that  ;D
https://secure.aspects-supplies.co.uk/products/showproduct/470
Wow that is an idea!  I'd have to keep the footballers off the melodeon then wouldn't I!
Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Restoring Pre-War Hohner Club II
« Reply #19 on: December 28, 2009, 10:14:06 PM »

With respect, always get a second opinion about any major repairs.  If you have ever seen celluloid/acetone application (new manufacturing) you would know that what you did would be suicide.

For a glimpse of the process, here's a video presented by Kimric Smythe who toured the Weltmeister factory. The bit on celluloid is about 53 sec. in........... :-X

                         http://www.youtube.com/watch?v=rYsSifiDapo
Logged
Pages: [1] 2 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal