Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Custom Layout Reed Sourcing  (Read 988 times)

0 Members and 1 Guest are viewing this topic.

SPC

  • New Starter
  • Offline Offline
  • Posts: 1
Custom Layout Reed Sourcing
« on: March 11, 2026, 02:15:37 PM »

Hello! This is my first post here. I haven't looked very far into the old threads, so I'm just diving in. Hope that's okay!

I have been designing my own layout for a two-row (originally C/F+accidentals) push-button accord, which always has a scale-degree interval between push and pull (C goes to D, e.g.). I was originally thinking I would simply unwax and rearrange the reeds to match the other changes in my layout, but I realized that the push and pull are the same piece.

I'm okay with reusing the reeds from the original layout, but since the tongues are riveted on, it seems like it would be difficult to switch them around. If I sand them like I see you're supposed to for tuning, it seems like the change of 100+ cents is probably too much.

The plates are are 16mm wide. I expect I may need to make a new reed block, and that's fine.

How should I economically source the reeds for my custom layout?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Custom Layout Reed Sourcing
« Reply #1 on: March 11, 2026, 02:23:51 PM »

First thing you need is an understanding of how far you can tune a reed above or below it's original pitch while retaining good response, and stable pitch.   There isn't a simple answer to this.  It is different for lower pitches where you can add or remove tip load to make quite big changes, and high pitches where reed tips are usually thin which limits how far you can raise the pitch.  High pitch reeds are thicker from in the half of the reed nearer the rivet and you can safely remove metal from there to lower the pitch.   There are more fine details than that, but it's a good starting point to learn from.

You can get reeds from old melodeons or accordions that are not worth repairing.  If you want modern reeds then things are more difficult.  Reed makers want a minimum order of several sets of the same specification.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Custom Layout Reed Sourcing
« Reply #2 on: March 12, 2026, 04:09:54 AM »

I've made my own diatonic reed sets from old piano accordions quite a number of times.  Most recently I made a full set of treble and bass reeds for a 23-button, 3v (MMM) box of mine and the instrument turned out superbly!  I have many full sets of high-quality (TAM or A-Mano) piano accordions to work from, and I'll make very specific choices about which set to use based on various qualities of the reed (tonal properties, reed response, etc).  I've often preferred the results of my labour to actual diatonic reeds purchased from reed makers.

In most cases you can usually take a reed up or down in pitch by up to a tone, but it does depend on several factors and there's a lot to consider.  It's important to examine the profile of the reed, to see how much material one has to work with at the tip and at the base of the tongue.  Solder can always be used to lower pitch, but doing so can also impact reed response and tone.  I generally try to use as little solder as possible. 

In examining the profile of the reed tongue, it's also important to take note of where the reed 'hinges' along the length of the tongue.  This hinge point is an area you generally don't want to significantly alter in terms of thickness because it can affect how the reed performs.  You want to avoid removing too much material in any one spot that would affect how the reed tongue swings.

For making diatonic reeds from old piano accordion reeds, I usually 'split the difference': to make a D/E reed, I will use a D#/D# reedplate and tune one side down to D and the other side up to E.  When the difference between the two sides begins to get further apart (and the top and bottom of your keyboard), you have to make some choices.  With higher reeds, I will avoid raising the pitch too far as the reed tips are much thinner to begin with; conversely, since the lower portion of these higher reeds is much thicker, it allows the pitch to be lowered a fair amount without compromising the reed.  With lower reeds, I'll split the difference as much as I can and then carefully use a small amount of solder to go the rest of the way, if necessary.  If you just use solder, I find it can be too much and the reed can sound duller and be more sluggish to respond.  But there are a lot of subtleties at play...
Logged
C#/D player

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Custom Layout Reed Sourcing
« Reply #3 on: March 13, 2026, 12:38:13 PM »

What mselic sez. I too have a large collection of old PA reeds, some of superb quality. Look out for old accordions on eBay. Unrefurbished they either don't sell or go for £40 or so (because the refurbishment cost of a 41/120 PA is 20 to 30 hours..and therefore you're better off spending that money on a decent working PA).

JNM SY

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 227
Re: Custom Layout Reed Sourcing
« Reply #4 on: March 13, 2026, 05:24:56 PM »

"to make a D/E reed, I will use a D#/D# reedplate and tune one side down to D and the other side up to E."
I started out doing it this way but due to sometimes not having the required reed (and laziness)  I will use an E/E reed and solder the tip of one down to give you D/E,
so only having to alter one reed.
I mostly find going down in pitch easier than going up.
( But I'm getting old and deaf now🤫).
 
Logged

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Custom Layout Reed Sourcing
« Reply #5 on: March 14, 2026, 02:08:57 AM »

I've made my own diatonic reed sets from old piano accordions quite a number of times.  Most recently I made a full set of treble and bass reeds for a 23-button, 3v (MMM) box of mine and the instrument turned out superbly!  I have many full sets of high-quality (TAM or A-Mano) piano accordions to work from, and I'll make very specific choices about which set to use based on various qualities of the reed (tonal properties, reed response, etc).  I've often preferred the results of my labour to actual diatonic reeds purchased from reed makers.

In most cases you can usually take a reed up or down in pitch by up to a tone, but it does depend on several factors and there's a lot to consider.  It's important to examine the profile of the reed, to see how much material one has to work with at the tip and at the base of the tongue.  Solder can always be used to lower pitch, but doing so can also impact reed response and tone.  I generally try to use as little solder as possible. 

In examining the profile of the reed tongue, it's also important to take note of where the reed 'hinges' along the length of the tongue.  This hinge point is an area you generally don't want to significantly alter in terms of thickness because it can affect how the reed performs.  You want to avoid removing too much material in any one spot that would affect how the reed tongue swings.

For making diatonic reeds from old piano accordion reeds, I usually 'split the difference': to make a D/E reed, I will use a D#/D# reedplate and tune one side down to D and the other side up to E.  When the difference between the two sides begins to get further apart (and the top and bottom of your keyboard), you have to make some choices.  With higher reeds, I will avoid raising the pitch too far as the reed tips are much thinner to begin with; conversely, since the lower portion of these higher reeds is much thicker, it allows the pitch to be lowered a fair amount without compromising the reed.  With lower reeds, I'll split the difference as much as I can and then carefully use a small amount of solder to go the rest of the way, if necessary.  If you just use solder, I find it can be too much and the reed can sound duller and be more sluggish to respond.  But there are a lot of subtleties at play...

While this is possible ... it's worth remembering that reed manufacturers profile the reeds differently for use in a bisonoric instrument like a piano accordion vs a unisonoric instrument like a melodeon. This is because with a push-pull instrument you need the reeds to sound quicker than you would need for one played all in the same direction.  So even between Hohner reeds of a similar era ... piano accordion reeds are less well suited for retuning to diatonic needs than original diatonic reeds.

Cheers

Squeezy
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Custom Layout Reed Sourcing
« Reply #6 on: March 14, 2026, 03:15:39 AM »

Quote
While this is possible ... it's worth remembering that reed manufacturers profile the reeds differently for use in a bisonoric instrument like a piano accordion vs a unisonoric instrument like a melodeon. This is because with a push-pull instrument you need the reeds to sound quicker than you would need for one played all in the same direction.  So even between Hohner reeds of a similar era ... piano accordion reeds are less well suited for retuning to diatonic needs than original diatonic reeds.

I've wondered about this, but I'm not entirely convinced.  Keep in mind that I've done direct comparisons of different reeds (diatonic-from-factory vs unisonoric-turned-bisonoric) in the same instrument and on the same reedblocks, and I've often found that I preferred the ones that were repurposed from PAs.  For example, I've installed multiple sets of Voci Armoniche TAM diatonic reeds in instruments (the very same reeds that Castagnari uses in nearly all of their diatonic accordions), had them played regularly for a year or so to break them in, then replaced them with reeds I'd 'made' myself from old TAM/A-Mano PA reeds and found the latter to be superior in tone as well as response.  I'm certainly not saying that would always be the case, mind you.  There are so many factors that contribute to the timbre and response of a reed that it's difficult to say why one is 'better' or 'easier to play' than another.

Comparing Hohner PA reeds to Hohner diatonic reeds from the same era, I've not been able to detect any difference in the profile/shape/tone/response between the two.  I'm willing to be shown otherwise, but as of right now I'm not convinced there's a difference! 

One thing I have sometimes noticed with PA reeds is they tend to be longer-scale compared to some diatonic makes.  I find that longer-scale reeds tend to give better dynamic range, but it can be true that having a reed like that, coupled with a tight reed gap setting, can make the reed feel a little stiffer in the push-pull dynamic of a diatonic box.  At the same time, Binci reeds are quite long-scale and they are a dream to play even when new!

Anyhow, those are just my observations from my experiences.  YMMV, etc...
Logged
C#/D player

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Custom Layout Reed Sourcing
« Reply #7 on: March 14, 2026, 03:58:25 AM »

Another thought...there are not nearly as many reed makers today as there were back in the heyday of accordions.  I have boxes full of old PA accordion reedblocks with TAM/A-Mano reeds, and none of them are the same!  Very few have identifiable markings, but in terms of reed profile/shape/length and their various properties, they are all quite different.  I know that some accordion factories used to have their own in-house reed makers, and I've heard that many in the industry consider reed-making to be a lost/dying art, or at the very least not what it used to be.  This is what I see with some of the reeds in these PA boxes that I have - a lot of range in terms of richness of tone and timbre, and I think it's that which I'm drawn to and what I've enjoyed about the ones I've repurposed into diatonic sets.  It's not that I think PA/unisonoric reeds are better than their diatonic counterparts, just that we don't have as much selection these days.

It's interesting to note that a lot of accordion builders would only ever put TAM/A-Mano reeds in their PA boxes, whilst their diatonic ranges would get super-dural/machine-grade reeds.  It's still the case with many accordion manufacturers that make both PAs and diatonics.
Logged
C#/D player

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Custom Layout Reed Sourcing
« Reply #8 on: March 14, 2026, 07:28:39 AM »

I don't think pa reeds are profiled differently to diatonic reeds. Obvs diatonic reeds are differently profiled because the pitch is different, but PA reed response is the same as a melodeon in a rapid push pull scenario . And I work on a lot of PAs (and melodeons)

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Custom Layout Reed Sourcing
« Reply #9 on: March 14, 2026, 08:02:21 AM »

I appreciate that I'm continuing to drift this thread and I have worked on way less reed plates than these people. My observation is also that A Mano reeds from PAs make excellent diatonic reeds and my favourite (and only) 6 voice box is entirely repurposed reeds.
Having looked at lots more machine made diatonic reeds, but quite a few A Mano too, I wonder if the tongues start off the same on each side of the plate. It certainly looks that way on old Hohner boxes. Perhaps people who have worked in or toured reed workshops could help here.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Custom Layout Reed Sourcing
« Reply #10 on: March 14, 2026, 10:59:31 AM »

I've used a lot of PA reeds in conversions, and have a lot more in stock for future Frankenstinian work. I found that the main problem with them is that the length of the plate and the tongue often require quite severe block modifications. (I'm not up to making new blocks!) I store my reeds by plate length, writing the notes on the plate in pencil.

I'm interested in knowing how to recognize 'a mano' reeds. Obviously, hammered rivets are easy to spot, but otherwise???
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Paul Bryan

  • Member
  • *
  • Offline Offline
  • Posts: 37
Re: Custom Layout Reed Sourcing
« Reply #11 on: March 14, 2026, 08:16:25 PM »

amano reeds are cut from a thin strip of steel and therfore the blue edge is visable athe bass of the reed where it is riveted to the aluminium
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Custom Layout Reed Sourcing
« Reply #12 on: March 15, 2026, 07:58:24 AM »

Thanks, Paul. I'll look out for that! Is it always the case?
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

odonovanchris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 276
    • Instagram Accordion Profile: chris0donovan
Re: Custom Layout Reed Sourcing
« Reply #13 on: March 17, 2026, 04:37:24 AM »

I'll add my 2 cents to this conversation since I'm obsessed with this stuff.

The optimum accordion reed tongue profile will result in a reed that sounds at the same pitch across the pressure range of play. So A4 pianissimo would be 440.0 Hz and fortissimo would also be 440.0Hz and also everything in between. Now suppose your reed is rectangular in shape like the old DIX Gera reeds - you would grind a particular curve to obtain these properties. But when you get to the higher notes what begins to happen is you don't have enough material at the tip of the reed for structural integrity so the reed will easily snap. To solve this they created a trapezoidal tongue shape - this allows for a thicker tip which is stronger. But this creates another problem - the width of the tip is narrower so chops less air per stroke therefore producing less harmonic content in the resulting note. This is great if you're Julio Giulietti and looking for a warm woodwind sort of sound - but not if you're a Bavarian Harmonika player or lover of wet harmonically rich musette sounds. Because we've changed the shape of the tongue we also have to adjust the grind profile to maintain the ideal pitch/pressure ratio.

When you get to the lower notes you'd need much longer reed tongues for the same gauge thickness of strip steel - they won't fit in an instrument of practical size. You could thicken the steel used for the manufacture of the tongues to keep them short but this will require more powerful and expensive punch presses and your tooling will wear out faster, or you could weight the end of the tongue to lower the pitch. The problem with weighting the tip is that it completely ignores the optimum profile and therefore the pitch shifts at varied pressures. This is very noticeable when tuning bass reeds and you have to carefully balance the pitch curve to minimize the time the reed is out of tune. Most of the time the bass reed will be paired with another reed an octave higher to encourage acoustic coupling of the two reeds. Since the smaller reed has the optimum profile it will act to lock the bass reed into pitch faster. I've observed this in Hohners as old as the 1920s but it seems recent manufacturers are not doing this anymore - I'm thinking the knowledge transfer hit a brick wall. Russian bayans use much longer and thicker bass reeds, everything is fully handmade on the best instruments and the pitch response is excellent. They still weight the ends but I believe they hand file a good profile into the base of the tongue to minimise pitch shift.

The pivot point of a reed tongue actually moves along the tongue when the pressure increases. For a mid-range reed say C3 If it starts at 1/4 of the tongue at pianissimo it will move towards the rivet when increased to fortissimo. This is the reason that the lower middle part of the tongue is so critical to the overall stability of a reed and filing should be avoided in this area. I've heard this area being called the "dynamic range". From my experimentation I think this is why changing the pitch of a reed by more than 1 tone starts to encounter all these problems. The tongue is optimised for its original design and when you mess with it you will quickly make a mess of the sound. Now suppose you're making harmonicas instead - you actually want the ability to shift pitch easily vs pressure so the grind profile will be flatter. Or how about that lovely Jeffries honk!?

I suppose what I'm trying to say here is that reed design is full of compromises and there's an infinite number of ways you can shape a reed tongue for optimum pitch/pressure performance. Now if you take an existing reed and change the pitch you will quickly ruin this pitch/pressure curve unless you are very skilled at listening and sanding in the correct place and dedicate the time to maintain its performance over the full pressure range. It takes a lot of time which isn't practical in most cases unless you're making replacement reeds for top heirloom quality accordions using vintage stock. When I first started working on reeds I filed a Hohner reed so badly that when the pressure increased the pitch went way up - this was the result of the profile being completely ruined and when paired with another reed the tremolo went all over the place when bellows pressure changed. Luckily I don't do that anymore but it was a good lesson and sent me down the rabbit hole of reed design. I can imagine that the old masters of reed making (Guidobaldi, Nazzareno Binci, Vincenzo Taborro to name a few) had a lifetime of experience of balancing all these considerations to make brilliant reeds for the specific needs of their customers and ultimately the musicians that still cherish instruments with their reeds today.
Logged
See my accordion projects on Instagram: https://www.instagram.com/chris0donovan/

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Custom Layout Reed Sourcing
« Reply #14 on: March 17, 2026, 07:56:44 AM »

Thanks for that little lecture. Intimidating to those of us who mess about with reeds without really understanding what we've been doing wrong! And also why we've been getting particular results, sometimes, with our efforts.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Custom Layout Reed Sourcing
« Reply #15 on: March 21, 2026, 04:06:23 PM »

Thank you, Chris, for that very informative response!  I'd love to continue the conversation with you sometime.

Quote
I suppose what I'm trying to say here is that reed design is full of compromises and there's an infinite number of ways you can shape a reed tongue for optimum pitch/pressure performance. Now if you take an existing reed and change the pitch you will quickly ruin this pitch/pressure curve unless you are very skilled at listening and sanding in the correct place and dedicate the time to maintain its performance over the full pressure range. It takes a lot of time which isn't practical in most cases unless you're making replacement reeds for top heirloom quality accordions using vintage stock.

Making an entire set of reeds this way *IS* a lot of work, and not something I'm in a rush to do too often.  And yes, you have to be very mindful of how you approach each reed to get optimal performance when re-pitching.  The flipside, if you are willing to put the time in, is that you have more options available to you in regards to choosing reeds based on tone and response and making a set from them.  If one has many different sets of high quality reeds from PAs, this can give you more options than what's currently available from diatonic reed makers.  It's also a lot cheaper and faster (faster in that you need not wait months for a reed order to arrive). 

I feel like our options for different makes of diatonic reeds is somewhat limited these days.  There really are only a few different reed producers, and most of them won't even deal with consumers directly. The reeds that I've liked best aren't available anymore.  It's for this reason that going the route of repurposing PA reeds can sometimes be a good way to go.  It's just another option.  I'd always sooner just buy a set of diatonic reeds ready-to-go if I know and like what I'd be getting.
Logged
C#/D player
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal