Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: how to put put a thumb groove into a wooden keyboard?  (Read 665 times)

0 Members and 1 Guest are viewing this topic.

kenakordeon

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 264
how to put put a thumb groove into a wooden keyboard?
« on: March 19, 2026, 05:15:14 PM »

I have a Cajun-style single row. I want to route a thumb groove into the edge of the keyboard. I have a table and router but would appreciate getting advice and directions on how to do this. I have plenty of scrap wood I can practice on before getting to the keyboard. One question is how deep of a groove is "ideal?"

The keyboard wood is walnut.

Thanks for any help.

Ken
Logged

tirpous

  • Hero Member
  • *****
  • Online Online
  • Posts: 1403
Re: how to put put a thumb groove into a wooden keyboard?
« Reply #1 on: March 19, 2026, 05:31:32 PM »

Quote
One question is how deep of a groove is "ideal?"

A good place to start would be to find an instrument with a groove you like, and measure and copy that. Not everyone has the same idea of ''ideal'' !

Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: how to put put a thumb groove into a wooden keyboard?
« Reply #2 on: March 20, 2026, 07:33:47 AM »

If you have a table router, but don't know how to use it, I'd focus your initial attention at learning the health & safety basics of using a table router.
While not the workshop's most dangerous tool, it can do a lot of damage very quickly, particularly to your fingers.
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: how to put put a thumb groove into a wooden keyboard?
« Reply #3 on: March 20, 2026, 08:18:19 AM »

If you have a table router, but don't know how to use it, I'd focus your initial attention at learning the health & safety basics of using a table router.
While not the workshop's most dangerous tool, it can do a lot of damage very quickly, particularly to your fingers.
Wise words

Toby B

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: how to put put a thumb groove into a wooden keyboard?
« Reply #4 on: March 20, 2026, 09:04:00 AM »

In practical terms ... a router in a table would be an ideal tool ... using a "radius cutter" "cove" bit with a diameter and radius to suit your chosen groove profile ... have the keyboard vertical against the fence with the front edge down against the router bit ... and pass smoothly right-to-left to cut the cove. Depending on your setup, if your fence isn't particularly tall, you might want to clamp a board to it to make it much taller, so the keyboard stays consistently vertical ... and your hands are safely further away from the cutter?

https://www.axminstertools.com/accessories/power-tool-accessories/routing/router-cutters/radius-cove-cavetto
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Online Online
  • Posts: 1327
  • Re-hohn a Hohner
Re: how to put put a thumb groove into a wooden keyboard?
« Reply #5 on: March 20, 2026, 10:56:00 AM »

https://youtu.be/vVlvwJelz9s?si=MK5bstzC476HHYEc

This is roughly how I would do it.
My approach to H&S is not as sketchy though.
Pariselle keyboards are grooved this way.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

kenakordeon

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 264
Re: how to put put a thumb groove into a wooden keyboard?
« Reply #6 on: March 20, 2026, 12:58:02 PM »

Thanks to all for your advice and the links. I will practice on scraps before attempting the work on the keyboard.
Logged

JNM SY

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 227
Re: how to put put a thumb groove into a wooden keyboard?
« Reply #7 on: March 20, 2026, 02:45:31 PM »

If you use matching walnut, you could router a thumb groove in a thin strip and try it in place with double sided tape before commiting to glueing or screwing it in place
permanently. I would rather add a strip of wood on than
 modify the existing keyboard.
         Good luck.
Logged

tirpous

  • Hero Member
  • *****
  • Online Online
  • Posts: 1403
Re: how to put put a thumb groove into a wooden keyboard?
« Reply #8 on: March 20, 2026, 05:30:54 PM »

Not sure what Ken's box is, but the typical Cajun keyboard (Acadian and clones) has an inverted 'U' cross-section. Turning the convex top into a concave groove may present challenges. And an add-on groove strip would need to be shaped underneath to fit the keyboard top.

Using a thumbstrap avoids all these complications !   >:E   
Logged

Dick Sadler

  • Good talker
  • **
  • Offline Offline
  • Posts: 62
  • Pt.
Re: how to put put a thumb groove into a wooden keyboard?
« Reply #9 on: March 20, 2026, 07:10:57 PM »

I purchased a plastic keyboard, cut the rounded edge off completely and ran a length of strong woven gaffa tape down the resultant slot! This compressed into a nice recessed thumb groove….and…I still have the original just in case.
Logged
If I didn’t have bad luck, I wouldn’t have any luck at all.....

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 613
Re: how to put put a thumb groove into a wooden keyboard?
« Reply #10 on: March 20, 2026, 09:16:59 PM »

I use 2-3 simple hand tool to do this on Honers & I have no wood working toll or skill   :-[
I mark 2 lines parallel to the edge and shave off some wood with small chisel-enough to guide a rotary/dremell sanding bit, do 5-6 or more passes on the bench drill with sanding bit attached to it,4-5 mm deep -dremell bit gives a reasonable curvy shape, and sand it down by hand to smooth curve.. sounds like long job but it only take 30 min. start to fininsh really   (:). 
Logged

komat

  • Eastcoaster
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 228
Re: how to put put a thumb groove into a wooden keyboard?
« Reply #11 on: March 21, 2026, 11:46:07 AM »

You could also cove cut across a table saw with an angled fence.
Logged
Too many accordions, help!

kenakordeon

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 264
Re: how to put put a thumb groove into a wooden keyboard?
« Reply #12 on: March 22, 2026, 02:08:01 PM »

Thanks again to you all for taking the time to give advice and comments. I'll practice both with a router and then hand chisels and see which method I prefer.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal