Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Padding option for old stepped keyboard buttons?  (Read 865 times)

0 Members and 1 Guest are viewing this topic.

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
Padding option for old stepped keyboard buttons?
« on: April 20, 2026, 07:52:15 PM »

I have a Paolo Soprani from 1952 (at least, that when it was sold to the first owner) that I'm finally getting around to fixing up and I've come to a small complication with the action. The abalone keys never seem to have had some kind of felt under them but this is stepped action, so when depressed, the buttons clack against the keyboard. It's not too intensely loud, but I'd like to pad them, even if just lightly

I reckon I could try to take the keyboard out and pad under the levers themselves, which would mean padding would have to be tall enough to engage the lever before the button engages the keyboard itself, which seems very impractical, so padding the keys seemed the most logical choice.

Anyway, I have looked for discs of felt for accordion buttons that I could perhaps sandwich under the buttons when screwing them down, however I suspect this might lend the buttons to gradually unscrew themselves too.

Does anyone have any ideas? Usually mushroom and screwed in step action buttons these days have padding in the design but I'm not sure about this particular situation.





Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Padding option for old stepped keyboard buttons?
« Reply #1 on: April 20, 2026, 09:56:20 PM »

Glue small pieces of felt on the underside of the buttons on either side of the wooden lever (so you have two small pieces of felt for each button). The felt will come to rest against the keyboard when the button is depressed, rather than the underside of the button ‘clacking’ against the keyboard.
Logged
C#/D player

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Padding option for old stepped keyboard buttons?
« Reply #2 on: April 20, 2026, 10:15:34 PM »

I guess you could have felt donuts with a largish center hole (hole diameter equal to the wooden key width or slightly less) and a washer of a hard material to fill the hole, so that the button is 'hard to the key', but 'felt to the keyboard surface' if you see what I mean.

I have a 1920-30s wooden Paolo Soprani with no felt padding under the button, the keys seem to stop before the button hits keyboard surface, so maybe padding behind the key  ?

Also a couple of Belgian boxes from the same period. One has rather thin felt discs under the buttons and the buttons do spin and/or wobble, so not the best approach. The other has squarish buttons screwed directly to the wooden keys with (as far as I can tell) 2 small strips of felt glued under the button overhangs either side of the key.

Hope this helps.

ps ah I see mselic has already replied along the lines of my 'Belgian #2'  (:)

Logged

Fionn

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 194
Re: Padding option for old stepped keyboard buttons?
« Reply #3 on: April 20, 2026, 10:39:41 PM »

Open hole flute pads might save you some time cutting up felt. You can get basic ones quite cheaply and they should do the job.
Logged
Vintage Double Ray C#/D

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Padding option for old stepped keyboard buttons?
« Reply #4 on: April 20, 2026, 11:21:56 PM »

The usual option is to use the circular pads and then apply a drop of superglue to the screw thread before screwing it in.
It's strong enough to prevent movement but if the screw needs to be removed again the glue will break.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Padding option for old stepped keyboard buttons?
« Reply #5 on: April 21, 2026, 07:31:51 AM »

A sheet of felt, a couple hole punches (larger one that's about 1mm less than button diameter, and smaller one for the center hole) and a tube of glue is what you need.

The felts are usually 2mm and held by either screw pressure alone (on round-post modern alloy keyboards), or the felt is glued to the bottom of the keys.
I use a tiny drop of shoe glue, but it might present some challenge when replacing pads. A tiny drop of PVA will probably be OK too.

An advanced option that I use on my wooden keyboard builds is to insert 4mm OD hollow spacer posts (cost a couple £ from Aliexpress), where I can set the button travel depending on the post height.
Here's an example of a 4-mm raised button, but when I want a flush button, I just use a 2mm-high post & 2mm-thick felt.
This solves the problem of uneven button contact with the key, and also means that all your keys are in line with the top of the keyboard - I can see from your Soprani photo that the second row of keys is raised above the keyboard instead.
You'll need longer screws if you want to go down this route.

I your case, if felt has never been there to begin with ( :o For a stepped keyboard that created a melodeon-castagnettes hybrid!), you might want to use something like thin 1mm melton cloth instead of 2mm felt.
« Last Edit: April 21, 2026, 07:43:54 AM by mChavez »
Logged

Fionn

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 194
Re: Padding option for old stepped keyboard buttons?
« Reply #6 on: April 21, 2026, 12:03:38 PM »

One quick thing I might try is stretching a rubber/silicone O ring (maybe 2mm cross section?) around one of the keys, pushing it up the post to just under the abalone, and seeing if it helps.

It might not work, but if you already have a set it would only take a couple of minutes to find out.

If it looks as if it might, you can buy a box of hundreds of them in different diameters and cross sections for about £7.
Logged
Vintage Double Ray C#/D

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
Re: Padding option for old stepped keyboard buttons?
« Reply #7 on: April 21, 2026, 04:03:54 PM »

Thanks for the ideas, folks.

I pulled the action pin enough out to pull one key/lever out of the body to see how much space I might have to work with. The spring head comes pretty close to the contact point of the lever, but for the sake of science I cut a small square of woven felt multiple times so I'd have a little stack to experiment with.

In order to prevent the button head from contacting the keyboard, I would have to get a piece of fairly dense felt (or cork maybe?) that would need to be 5~6mm tall to engage the underside of the lever before the button completely hits the keyboard.

Going this route would prevent too much alteration of the action I guess. I am a little suspicious about how much the material will compact overtime but maybe a dense cork could do a superior job than woven piano felt. Who knows.

I tried hunting around for felt discs that were maybe only 1 or 2mm thick to go behind the button but above the lever mount and have no such luck with anything that already has a hole, and the super glue idea is clever as a sort of loctite, I just dont know if the felt would still compact overtime and loosen or not and a broken one of these buttons would be a terrible shame.

The silicone or rubber o ring idea is interesting, but the contact point between where the button comes close to the lever arm wood on one side versus the other would mean it would be an oval or floppy when mounted but perhaps there's still something in there too that could be attractive and stable without much struggle. I'll think on i! Thanks!

Matt's idea of putting two little bits on either side of the button is interesting too, though a bit labor intensive. However if the padding under the lever doesn't really work, I might try several of the methods suggested here.
I've got a toddler and a partner who's going through chemo at the moment so my free time is extremely limited, so I'm trying to figure out what I can do quickly but still a good job at that.
« Last Edit: April 21, 2026, 04:06:16 PM by Ross Dubois »
Logged

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
Re: Padding option for old stepped keyboard buttons?
« Reply #8 on: April 21, 2026, 04:13:20 PM »

A sheet of felt, a couple hole punches (larger one that's about 1mm less than button diameter, and smaller one for the center hole) and a tube of glue is what you need.

The felts are usually 2mm and held by either screw pressure alone (on round-post modern alloy keyboards), or the felt is glued to the bottom of the keys.
I use a tiny drop of shoe glue, but it might present some challenge when replacing pads. A tiny drop of PVA will probably be OK too.

An advanced option that I use on my wooden keyboard builds is to insert 4mm OD hollow spacer posts (cost a couple £ from Aliexpress), where I can set the button travel depending on the post height.
Here's an example of a 4-mm raised button, but when I want a flush button, I just use a 2mm-high post & 2mm-thick felt.
This solves the problem of uneven button contact with the key, and also means that all your keys are in line with the top of the keyboard - I can see from your Soprani photo that the second row of keys is raised above the keyboard instead.
You'll need longer screws if you want to go down this route.

I your case, if felt has never been there to begin with ( :o For a stepped keyboard that created a melodeon-castagnettes hybrid!), you might want to use something like thin 1mm melton cloth instead of 2mm felt.

Hmm that's an interesting concept too. Increasing the height of the buttons would give me more room to work with padding. The action as it is, with pallet leather that is around 1.5mm on old solid slot-less wooden pallets that are attached to round steel rods with a strip of leather, is actually fairly low. I've ordered new pallets with more room to lower the rods closer to the sound board, while increasing the felt thickness to get the situation quieter. This would potentially change the button height as it is, but I intended to keep it pretty low by compensating for depths and thicknesses here and there.

There's about 6mm of space in the lever slots before the bottom of the lever contacts the keyboard slot below, so there might be some room to work with adjusting the steel rods and raising the buttons.

At present, it's either padding the buttons, or padding the underside of the lever at the contact point. I don't know which is technically easier or 'better' here, but I reckon padding the bottom of the lever slot might be the easiest. Maybe
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Padding option for old stepped keyboard buttons?
« Reply #9 on: April 21, 2026, 04:39:23 PM »

For a stepped keyboard it's usually the felt under the button that limits the travel.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Padding option for old stepped keyboard buttons?
« Reply #10 on: April 21, 2026, 05:51:47 PM »

Felt washer under the button is the way I would try first.  Carini supply felt washers ready cut with central hole in several different sizes and in black or red.  The felt is 2mm uncompressed, but is quite soft and packs down to well under 1mm when the button is screwed home. It's no different in principle to the way that modern stepped keyboards work.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
Re: Padding option for old stepped keyboard buttons?
« Reply #11 on: April 21, 2026, 06:27:55 PM »

My concern with found that route is that this button is pure shell, no backing or mounting material is under the shell, so if I sandwich a felt washer directly under it and apply screw pressure to keep the washer snugly in place, am I not potentially creating a pressure point where the shell could crack down the middle?

I found some guitar strap lock felt washers that are 2mm x 13mm which would do nicely, but I am a bit worried about the extra pressure that will be applied here. This instrument never seems to have had washers there and it was ordered this way. I have the original receipt for it from 1952 as well and oddly enough it was pretty expensive. The equivalent of $1130 today. Might have something to do with the Dix reeds, I don't know.
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Padding option for old stepped keyboard buttons?
« Reply #12 on: April 21, 2026, 07:35:08 PM »

I'd say there's no need to overtighten.  Do as Rees suggests and just add a drop of superglue when screwing in.  The superglue will indeed keep the button from coming loose but can still easily be unscrewed if needed.  I've used epoxy in similar situations and it was no trouble breaking the seal if/when needed.
Logged
C#/D player

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Padding option for old stepped keyboard buttons?
« Reply #13 on: April 21, 2026, 07:36:28 PM »

mChavez - lovely work on your keyboard components!
Logged
C#/D player

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Padding option for old stepped keyboard buttons?
« Reply #14 on: April 21, 2026, 10:09:31 PM »

Thanks - these will have fanned levers (18mm step between the buttons but 17mm step between soundholes), so I need to gradually fan the keys. The levers turned out a big ugly.
You can't see behind the top veneer, but each key is laminated from 2 strips of wood to add stability.

The PTFE bushings are questionable... I've read that Steinway had problems with PTFE deforming under spring tension with time, but I guess piano springs are a lot stronger than what we have in a button box.
My current box has PTFE treble bushings and the whole bass end runs on PTFE too, so I'm planning to open it all up in about a year's time and see if there's any deterioration over 24 months.
Logged

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Padding option for old stepped keyboard buttons?
« Reply #15 on: April 22, 2026, 08:06:16 PM »

Here are some photos showing an old Settimeo or Ficosecco with the felts under the entire button with abalone buttons. Since the felt is only compressing under the lever portion of the round felt it squeezes pretty flat. It definitely quiets the clicking noise.

Scott
Logged
too many boxes...please buy one, or two, or

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
Re: Padding option for old stepped keyboard buttons?
« Reply #16 on: April 22, 2026, 10:40:39 PM »

Hey Scott, thanks for the photo and info!
It was bizarrely difficult to find these felt discs on accordion supply sites in any thickness no greater than 2mm and I was just assuming I wouldn't have any luck finding any specifically for this kind of situation. The felt under my Castagnari Tommy buttons for example are like, maybe 4mm or so, which on this Paolo would be extreme in terms of how much lever movement it would take up when depressed

Since this thread was rolling with info, I thought to maybe look for piano felt discs, which were also a bit too thick and the central opening a bit too wide, but whilst looking at those I remembered guitar strap lock washers are nearly a similar size so I took a gander for some of those.

Viola! Found some red and white felt washers in 2mm thickness by about 12.5-13mm wide. I ordered some yesterday from miserable ol amazon and they showed up today. Took a button off, centered the disc, screwed it back down and it worked wonderfully without taking up too much lever throw!

https://www.amazon.com/gp/aw/d/B08LVJ2P83?psc=1&ref=ppx_pop_mob_b_asin_image

I'm glad this ended up being the easier option. I was not looking forward to padding under each wooden lever
Logged

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Padding option for old stepped keyboard buttons?
« Reply #17 on: April 25, 2026, 12:20:19 AM »

Nice solution! I used to cut them out manually with a hole punch and hammer but now can cut them out of sheets with my laser cutter.

Photos of old and new methods although these are for bass buttons, not treble so the inner hole is bigger.

Scott
« Last Edit: April 25, 2026, 12:42:07 AM by hickory-wind »
Logged
too many boxes...please buy one, or two, or
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal