Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Old Globe Gold Medal reed repair quandary  (Read 615 times)

0 Members and 1 Guest are viewing this topic.

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
Old Globe Gold Medal reed repair quandary
« on: August 26, 2026, 06:03:12 PM »

Hey folks

I just took receipt of an old Globe, and aside from a couple minor cracks in the sound boards, the only significant issue I have is that of the reeds.

The steel reeds themselves are astoundingly clean and in immaculate condition. Also in the key of D which is perfect. What isn't perfect is the plates. A number of the Zinc plates have expanded in size from corrosion and flake off dust and the like and I find myself trying to see just how badly that has affected the dimensions of the reed slot. The plates themselves were much thicker than say a hohner zinc plate, but a slot change is a slot change.

I am wondering if there is a chemical way to remove this oxidation so that I don't have to scrape the slots and breadth of the plates for all 40 of them. At least it would mean that if I find many are no longer fit for use I wouldn't have wasted hours manually scraping.

I tested one after scraping and even though the height of the plate had lowered slightly, the reed was able to be set and function well all the same so I have some hope.

If all fails then I'll have to see about slapping another reed set in here which seems a shame. The Globe reeds themselves are beautiful, but I lack the skill and time and insanity needed to remove each reed tongue and fit it to a new plate of corresponding size, that just seems preposterous.

Anyway, happy to hear what anyone might suggest that could save these
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Old Globe Gold Medal reed repair quandary
« Reply #1 on: August 26, 2026, 06:42:13 PM »

I think I would try cleaning in an ultrasonic bath.  That’s a good method for loose flaky dusty debris
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
Re: Old Globe Gold Medal reed repair quandary
« Reply #2 on: August 26, 2026, 07:15:58 PM »

Ah, grand idea, thanks Theo! I think I have one in fact. Do you use any sort of mild solvent in there or just water? I feel like something like vinegar would eat the reedplates apart

How long would you reckon I should let it run? I worry about steel rusting but Im not sure how long that would take
« Last Edit: August 26, 2026, 07:21:13 PM by Ross Dubois »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Old Globe Gold Medal reed repair quandary
« Reply #3 on: August 26, 2026, 08:46:02 PM »

There are special cleaning solutions for non-ferrous metals, often described as for sensitive metals. I tried ultrasonic cleaning for reeds,  but for normal use I found it was slower than mechanical cleaning.  Also make sure to dry the reeds as soon as they come out of the bath, or you will get a film of rust forming in minutes.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Old Globe Gold Medal reed repair quandary
« Reply #4 on: August 27, 2026, 03:56:19 PM »

Before retiring from Rochester Institute of Technology, in my building, we had a lab dedicated to studying practical restoration of things and entire machines. One of the methods used was baking soda blasting. A common demonstration used for visitors was blasting the paint off of thin-walled aluminum soft drink cans. It completely removed the paint but left the aluminum fully intact. (see pic 1) A sand blaster would punch through the can wall in seconds.

I procured a small tabletop media blaster that is used in the dental field for cleaning up gold castings for crowns. It has two separate canisters for media with a manual air valve for selection. I keep sand in one for derusting metal parts like Hohner keyboard levers. The other has baking soda. (see pics 2 & 3) I have tried many other methods (mechanical and chemical) for derusting and reedplate cleanup and nothing comes close. It is fast, non-destructive, and removes rust, valve glue and wax residue. I have cleaned up thousands of reedplates with it. As you can see, I added labels inside and out to prevent accidentally using sand on the reeds themselves as that will alter (work harden) the surface structure of the reed causing significant warping. While blasting the opposite side will usually cause the reed to flatten back out, it is too severe a process and so should be completely avoided.
« Last Edit: August 27, 2026, 04:10:09 PM by hickory-wind »
Logged
too many boxes...please buy one, or two, or

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Old Globe Gold Medal reed repair quandary
« Reply #5 on: August 27, 2026, 04:01:18 PM »

Here are before and after photos. Notice it not only removes the glue and wax residue, it removes the rust but beautifully leaves the steel bluing fully intact. The process is fast. The twin blaster cost about $185USD when I bought it 10 years ago but probably paid for itself in a few months of saved labor. It works very well with the old zinc reedplates. The unit comes with full rubber gloves. I found those quite cumbersome and unnecessary. I swapped for sleeves with rubber band cuffs so I can put my hands in (with reedplates in hand) for better manipulation and control. The soda (and sand for that matter) does not injure or even bother my fingers in use. That also means I don't need to open the large and heavy glass lid unless working on a large item.
« Last Edit: August 27, 2026, 04:09:13 PM by hickory-wind »
Logged
too many boxes...please buy one, or two, or

Clive Thorne

  • Member
  • *
  • Offline Offline
  • Posts: 32
Re: Old Globe Gold Medal reed repair quandary
« Reply #6 on: August 27, 2026, 06:13:36 PM »

Another gentle blasting material is crushed walnut shells. Never used them myself as too gentle for what I blast (mostly car parts), so can't comment on the effectiveness.
Logged

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
Re: Old Globe Gold Medal reed repair quandary
« Reply #7 on: September 04, 2026, 03:03:49 PM »

Thanks so much for the recommendation, Scott! They appear to still be fairly priced. I really like this idea.
I have discovered a few reed plates have been too badly corroded, making the gaps around the reeds too wide, but there is still a lot to salvage and this machine could help much more effectively I reckon. Plus it would be great for any other number of projects I have.

Thanks so much!
Logged

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Old Globe Gold Medal reed repair quandary
« Reply #8 on: September 04, 2026, 03:56:05 PM »

Ross-
You're welcome. You won't regret it. I use an older vacuum cleaner (on its mildest vacuum setting) connected to the exhaust port on the back to create a negative pressure keeping my shop clean. The first one I bought came with clear plastic media canisters which I thought was a great idea-to be able to see the media level without opening it up. One day while working, the plastic threads failed and one of the lids flew up and hit the ceiling. It made quite a boom at 60psi !!! I contacted the company and they sent me all metal canisters to replace the clear ones. Not sure if they are still offering both kinds but if they are, select the all metal ones. The photo shows my handmade sleeves that replace the full rubber gloves that came with it. Much easier to get reedplates in and out and better manipulation while in hand. If I have marked a number or note on a reedplate (ultra fine Sharpie permanent marker) I can manually mask that area with a thumb or finger while blasting. Looks like the price has come down since I bought mine. Best of luck.

Scott
« Last Edit: September 04, 2026, 04:06:54 PM by hickory-wind »
Logged
too many boxes...please buy one, or two, or

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Old Globe Gold Medal reed repair quandary
« Reply #9 on: September 04, 2026, 04:03:35 PM »

Mine didn't come with interior lights so I added some strip LED lights. Seems that some of them include that upgrade now. I also replaced the over-center toggle clamp with strong magnets. It seemed overly complicated. I see they are stocked here in the States now also. Should be able to get one quickly.
« Last Edit: September 04, 2026, 04:05:42 PM by hickory-wind »
Logged
too many boxes...please buy one, or two, or
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal