Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Retuning C/F to D/G  (Read 722 times)

0 Members and 1 Guest are viewing this topic.

Clive Thorne

  • Member
  • *
  • Offline Offline
  • Posts: 32
Retuning C/F to D/G
« on: September 08, 2026, 10:23:01 PM »

So, converting a Hohner CF Club to DG: Do we tune every reed up by a tone, or swap reeds around to minimise the retuning, and then fill in the gaps from other sources?

Which would you do?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Retuning C/F to D/G
« Reply #1 on: September 08, 2026, 11:27:23 PM »

I’ve done this many times.  Always move the reeds around to minimise the amount of pitch change.

Expect the first time you do this to be a learning experience and have some spare reeds available to replace the inevitable small disasters!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Retuning C/F to D/G
« Reply #2 on: September 08, 2026, 11:33:18 PM »

It helps to have a spare dead Hohner piano accordion of similar vintage as a reed donor.
And do as Theo says. Plan it all out first for the most optimal repositioning.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Retuning C/F to D/G
« Reply #3 on: September 09, 2026, 07:40:16 AM »

The pdfs below show my schema for converting c/f pokerworks to d/g, may give you a start

Clive Thorne

  • Member
  • *
  • Offline Offline
  • Posts: 32
Re: Retuning C/F to D/G
« Reply #4 on: September 09, 2026, 03:39:28 PM »

Thanks for the thoughts. I do have a the reed blocks from a dead Hohner piano accordion. These are zinc and stamped "T" the same as the melodeon ones, so hopefully will sound & respond similarly (please advise).

I have two:

A "Club Modell I Piccolletta" 10/9/4, which is pretty much the same size as a Pokerwork, and weighing a bit more at 3.3kg (4 extra reeds, and zinc reed plates, I guess)

A "Club Modell II" 11/10/4, which is a bit bigger than a Pokerwork, and weighing a bit more at 3.3kg (8 extra reeds, and zinc reed plates, I guess). I will probably make this one a 4th button start as well.

I don't know why the slightly larger box weighs the same, as it has an addition 4 reeds (also zinc), but the kitchen scales cannot lie!


The background to this is that for many (many many) years i have played a Castagnari Rik, but took up with my old Pokerwork again a couple of years ago for playing for Morris & sessions. Recently picked up the Rik again and my first thought was "Bloody hell this is heavy and cumbersome", and to reach for the pokerwork ( I have always played standing up for morris and band playing - even with the Rik). Hence thinking about an early Club model to get some flexibility without the weight.

Anyway, a further question, if starting say aiming for G/A reed, starting from a piano accordion reed, would you go an A/A Reed and flatten one to the G (Solder?), start with G/G and sharpen one, or start with an A#/A# and split the difference.


Thanks again for your thoughts & advice so far.

Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Retuning C/F to D/G
« Reply #5 on: September 09, 2026, 04:11:03 PM »

Anyway, a further question, if starting say aiming for G/A reed, starting from a piano accordion reed, would you go an A/A Reed and flatten one to the G (Solder?), start with G/G and sharpen one, or start with an A#/A# and split the difference.
Any of those dependant on what reeds are available

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Retuning C/F to D/G
« Reply #6 on: September 09, 2026, 05:16:15 PM »

When I'm retuning I make a list of all available reeds using reed numbers rather than actual pitch. The Italian numbering system works well for this.
Then I do a similar list for what I want to achieve.
Now it's a lot easier to see where you're going and you'll probably find that small alterations to two reeds is better than reusing one as is then finding there's too much to change on the next one.
I generally don't like to sharpen reeds more than one semitone. Theo might tell you which ones work.
Lead loading works for me. Keep the blobs cushion shaped if you can as I think that alters the airflow through the slot the least.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Retuning C/F to D/G
« Reply #7 on: September 09, 2026, 05:28:04 PM »

I do something similar, with the reeds arranged I order of pitch.  Then another list for the target reeds also in pitch order.  If you do these on two different sheets of paper you can usually spot the best match.

How far can you change pitch?  It depends.  It helps to have an understanding of how reed profiles change across the pitch range. Low pitch reeds are thin in the centre to lower third,  so you don’t want to make that thinner.  They are thick at the tip so it’s usually possible take the pitch up by more than a semitone.  You can also lower the pitch by tip loading with solder.

High pitch reeds are thinnest at the tip, so tuning up is more restricted.  A semitone is usually possible and more if you have a good file and can use it accurately.  The root of a high reed is thick,  so you can safely lower the pitch by a larger amount, a full tone is almost always possible and often more than that. Midrange pitches have intermediate profiles. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: Retuning C/F to D/G
« Reply #8 on: September 09, 2026, 09:42:04 PM »

its also worth mentioning that lower pitch reeds are often already tip loaded with brass. that gives you an opportunity to raise pitch on those often by a considerable amount. as theo often wisely says...often better to lower a reed with solder as its reversible so given a choice with accordion reeds where its same on pull and push i usually go for a higher reed and add solder or split the difference and raise one side by a semitone and lower the other side by a semitone. I look for a reed that speaks on very gentle pressure but doesnt choke on more pressure. Ivor Hyde in Chard taught me that 40 years ago! then check reeds together to make sure they speak together with no delay.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Retuning C/F to D/G
« Reply #9 on: September 10, 2026, 08:11:25 AM »

I take my hat off to you guys. I have done this a couple of times..but decided life is too short  (:) then I get a seemingly never ending stream of concertinas to flatten from 454 to 440..as a punishment.
In answer to the question
Quote
if starting say aiming for G/A reed, starting from a piano accordion reed, would you go an A/A Reed and flatten one to the G (Solder?), start with G/G and sharpen one, or start with an A#/A# and split the difference.
I generally tune up and down from the mid point. For a half tone i would not use solder. You can easily push half a tone either way (well..I can).
« Last Edit: September 10, 2026, 08:14:07 AM by Rog »
Logged

Clive Thorne

  • Member
  • *
  • Offline Offline
  • Posts: 32
Re: Retuning C/F to D/G
« Reply #10 on: September 10, 2026, 03:17:48 PM »

I take my hat off to you guys. I have done this a couple of times..but decided life is too short

Well, it is a lot of work, but it's also a way to get a lightish 2.4 row D/G at a sensible price. I quite enjoy fiddling with things anyway.
Logged

Clive Thorne

  • Member
  • *
  • Offline Offline
  • Posts: 32
Re: Retuning C/F to D/G
« Reply #11 on: September 10, 2026, 03:20:06 PM »

Also, another question (Sorry!).
Would replacing the original leather valves with plastic have any effect (good or bad) on tone/response etc.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Retuning C/F to D/G
« Reply #12 on: September 10, 2026, 03:49:45 PM »

It’s important to replace all the original valves.  Which type you use is your choice,  but plastic are less trouble than leather.  The only downside it plastic is that for larger reeds they can be a little more noisy.  I usually use composite valves that have a layer of leather with one or more layers of plastic on top. Many modern makers eg Castagnari do the same.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal