Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: adding solder to a reed  (Read 6707 times)

0 Members and 1 Guest are viewing this topic.

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
adding solder to a reed
« on: January 29, 2010, 02:32:02 PM »

Any tips on technique for lowering the pitch of a reed by adding solder to the tip?  Type solder?

thanks,
Michael
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: adding solder to a reed
« Reply #1 on: January 29, 2010, 03:00:36 PM »

I use flux cored solder designed for electronic work.  Lightly file the surface of the reed tip first to ensure the solder will stick.  Slip a piece of paper under the reed tongue to stop it retreating from the iron.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: adding solder to a reed
« Reply #2 on: January 29, 2010, 03:34:59 PM »

I didn't know that you could use solder for that purpose (:) One to remember, we have very high quality irons and solder in my Engineering department, just down the road.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Accordion Dave

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 380
Re: adding solder to a reed
« Reply #3 on: January 30, 2010, 02:16:35 AM »

I will be following this topic with interest as I have seen solder at the tips of the bass reeds of some my of my accordions.
Logged

Accordion Dave

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 380
Re: adding solder to a reed
« Reply #4 on: January 30, 2010, 02:17:21 AM »

Some of my accordions, that is.
Logged

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: adding solder to a reed
« Reply #5 on: September 30, 2012, 09:56:45 PM »

Reviving an old thread...

Electrical cored solder seems an OK choice to weight reeds - presumably leaded solder has been used, anyone tried unleaded solder on reeds? Any difference?

Also, choice of implement - I have a couple of reasonably meaty (by electronics standards) soldering irons, e.g. Weller TCP1 and something similar from Maplin for unleaded. Are these likely to be up to the job? I'm not ready at present to set up and try it, but it would be nice to be forewarned.

Seen reference to butane or jewellers gas tools being used - not sure if these used a direct flame? Feels like overkill - any thoughts?

Thanks

Malcolm
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: adding solder to a reed
« Reply #6 on: September 30, 2012, 10:03:34 PM »

I have successfully tip weighted using this iron which is only 18W. I use Maplins lead-free solder.

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: adding solder to a reed
« Reply #7 on: September 30, 2012, 10:26:18 PM »

Cheers Lester
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: adding solder to a reed
« Reply #8 on: October 01, 2012, 08:04:32 AM »

I've successfully used enamel paint on the tip to slightly lower pitch to dry the tone off. Much easier to apply or remove than solder. It depends how much you're trying to lower the tone  :D ;D  paint is only good for spot tuning
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: adding solder to a reed
« Reply #9 on: October 01, 2012, 08:15:05 AM »

Same here but with Nail varnish , easier to apply to old rusty hohner reeds than solder too . great for those little tuning touch ups and makes the ends of your reeds look nice into the bargain  ;D
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: adding solder to a reed
« Reply #10 on: October 01, 2012, 08:24:12 AM »

I have no doubt the paint varnish etc works for you both but I would have thought for the amount of pitch change they bring about the more normal file/scratch methods. I only use solder where more normal methods just won't work.

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: adding solder to a reed
« Reply #11 on: October 01, 2012, 09:09:09 AM »

Not really adding anything new, but I've also had good results with ordinary multicore solder and a 20w iron. As Lester says, it's a technique for lowering pitch significantly, not for minor adjustments.
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Andy Simpson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 938
Re: adding solder to a reed
« Reply #12 on: October 01, 2012, 10:24:58 AM »

Reviving an old thread...

Electrical cored solder seems an OK choice to weight reeds - presumably leaded solder has been used, anyone tried unleaded solder on reeds? Any difference?



No appreciable difference in the end results. Lead solder is a bit easier to use because it has a lower melting point and is softer and easier to shape, although it gunges up files more readily and there's the whole lead thing if you're paranoid about that...

You don't need a very powerful iron to get the reed hot enough so anything should do, although a chisel tip is much better than a pointed one. The really important thing is that both the reed and the iron are clean when you apply the solder. To prepare the tip of the reed I sand it and then finish with meths applied by a cotton bud.
Logged

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: adding solder to a reed
« Reply #13 on: October 01, 2012, 10:44:36 AM »

Same here but with Nail varnish , easier to apply to old rusty hohner reeds than solder too . great for those little tuning touch ups and makes the ends of your reeds look nice into the bargain  ;D

Any particular colour.....or is it just what you happen to be using at the time?  ;)
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: adding solder to a reed
« Reply #14 on: October 01, 2012, 10:50:07 AM »

I have no doubt the paint varnish etc works for you both but I would have thought for the amount of pitch change they bring about the more normal file/scratch methods. I only use solder where more normal methods just won't work.

Except that paint/nail varnish are easily reversible, particularly useful when you are drying out the tremolo and you go too dry!
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: adding solder to a reed
« Reply #15 on: October 01, 2012, 10:58:00 AM »

[Any particular colour.....or is it just what you happen to be using at the time?  ;)

Well, it`s black at the moment (Haloween month)  ;D . and Yep, it`s easily reversible, no possible altering the temper of the metal as no heat is used (dunno if reed steel is affected by temp - Lester?) .

For the record, Suzuki use (or used at some stage) Varnish or enamel paint to tune their melodicas, my 1970s one needed tuning because some had drifted off a few reeds leaving the tuning as the reed was made . given that like moothies, Melodica reeds are subjected to extreme condensation (and spit and whatever), I think well over 30 years shows the longevity of using paint for fine tuning .
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: adding solder to a reed
« Reply #16 on: October 01, 2012, 11:26:28 AM »

Steel is affected by heat of course, but you have to get well above soft soldering temperature before you start to draw the temper of the steel.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: adding solder to a reed
« Reply #17 on: October 01, 2012, 11:44:09 AM »

Same here but with Nail varnish , easier to apply to old rusty hohner reeds than solder too . great for those little tuning touch ups and makes the ends of your reeds look nice into the bargain  ;D

Have you noticed that when sensible shops are going broke in this economic drought, a rash of nail finishing shops start up?  I've got a slightly sour four-stop that could be going into Blazingsmoke with me so some slapper can fine tune it!  I've decided to have each reed done with an individual national flag, so it'll be a United Nations box.

Actually, I think this is a splendid idea for short/medium term touch ups , particularly on an older box with rusting problems.  All I need now is the courage to buy the varnish.  I wonder if different colours give different dry film thickness/weight?

Rob.
Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: adding solder to a reed
« Reply #18 on: October 01, 2012, 12:27:16 PM »

the nail strengthing stuff "Harder than nails" is thicker so better for larger tuning drops and the emergency re-gluing of valves, the glittery stuff is great for bass reeds and if you get the fancy nail pack you can use the little rhinestones and coloured glittery varnish to give your box the Baffetti Celebration look   8) the false Nails in the pack make super makeshift Harpsichord quills , plectrums and the thin ones on your little finger for reed-pinging ..

All I need is a melodeon related excuse for the black cocktail dress and 5" stillettos and I`m laughing ;)
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: adding solder to a reed
« Reply #19 on: October 01, 2012, 02:47:39 PM »

All I need is a melodeon related excuse for the black cocktail dress and 5" stillettos and I`m laughing ;)

He who laughs last... but I'm not entirely convinced it will be you!

Doesn't a cocktail dress ride up with the movement of the bellows?

Rob.
Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal