Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Reed Tools  (Read 7236 times)

0 Members and 1 Guest are viewing this topic.

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Reed Tools
« on: February 10, 2010, 08:15:28 AM »

I remember that a little while ago there was a discussion about reed tuning and someone (Theo, probably) posted a picture of a wooden handled Hohner reed scratcher and two small brass tapered tools for flipping under the reed tongue and supporting whist tuning.

Can anyone point me in the direction of that post, I cant find it, and can anyone tell me where would be the best place to get said items.

I've been using the Italian J shaped tool method, but remember reading somewhere that the German method was faster and less fiddly (both good things!).
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed Tools
« Reply #1 on: February 10, 2010, 09:42:41 AM »

The link is in this thread
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Reed Tools
« Reply #2 on: February 10, 2010, 10:26:55 AM »

Ta! Can you reveal where they came from or is it a trade secret?  ;D
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed Tools
« Reply #3 on: February 10, 2010, 10:53:19 AM »

The file is a Swiss saw file from Axminster tools, the bronze reed lifter/support tools are from Hohner, and the Italian style reed hook I made from a spring steel wire and a bit of scarp wood.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Reed Tools
« Reply #4 on: February 10, 2010, 11:13:34 AM »

Thanks - time to email Hohner!
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Reed Tools
« Reply #5 on: February 10, 2010, 08:09:15 PM »

Theo, I've looked everywhere but can't find this scarp wood of which you speak.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

strad

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 418
Re: Reed Tools
« Reply #6 on: February 10, 2010, 08:56:27 PM »

It's escarped!

Nigel
Logged

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Reed Tools
« Reply #7 on: February 10, 2010, 10:40:07 PM »

Or fallen off an escarpment.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed Tools
« Reply #8 on: February 10, 2010, 11:29:46 PM »

I think I used the larst piece.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Reed Tools
« Reply #9 on: February 11, 2010, 05:53:31 AM »

That's unfartunate........ :-X
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Reed Tools
« Reply #10 on: February 27, 2010, 06:06:25 PM »

I use both the Italian "key" and the German tool ("Rausheber"). I have a wide variety of the latter - it's a good thing to know how to make them yourself (f.ex. from high quality cabinet-scrapers or, even better, from reed-steel, cut into lengths of appr. 10cm, 6mm wide). You'll need at least 4 different sizes to cover all the reeds on the block. Larger reeds  are more easily dealt with using the Italian method (which would be perfect if one had three hands...). If someone is interested, I could post some pictures that will show you how they can be made.
Both methods will allow you to tune  without having to remove the reed blocks (at least in most cases). Thus, tuning  an average 3-reedbox becomes a matter of hardly more than half an hour (unless other problems occur...).
While both the It. key and the German "hook" are very useful tools, they are not used for the tuning itself: you will need appropriate files and scrapers. The latter can be purchased at rather high prices - again, if you are able to make them yourself, you'll save your money and can give it the shape you desire. 3 different sizes should do the job. They are easily made from worn-out tuning files (necessary tools: a propane burner for softening and tempering, grinding wheel or power sander for shaping, honing stone)
« Last Edit: February 28, 2010, 11:51:30 AM by diatonix »
Logged

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Reed Tools
« Reply #11 on: February 28, 2010, 09:35:37 AM »

I have got some home made tools which I've been using, but I want to take things up a gear with some better ones. Any pictures or opinions on making them would be greatly received.
Logged

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Reed Tools
« Reply #12 on: February 28, 2010, 04:59:03 PM »

I have got some home made tools which I've been using, but I want to take things up a gear with some better ones. Any pictures or opinions on making them would be greatly received.

I have devised a lifting tool out of (necessity and desperation) which works well, and is easy to make. I cut a slim strip of .001" .002" brass shim stock about 2"-3" long with a slight taper. I bend a short fold about 1/16" on the narrower end. By plunging this past the side of the reed tongue near its tip, the reed can then be fished thru the plate. Once retrieved, then a support can be slid in place and the shim removed. (Three hands are quite useful here)! The brass shim, because of its thin-ness, offers little difficulty with the clearance between reed and slot, and won't damage the steel reed in any way. One must take care to examine the fold on the shim periodically, because it will eventually break and might leave a small flake of brass in the underside of the reed chamber, which would be a PITA. I've found that I can use one dozens of times before making a new one.
« Last Edit: March 01, 2010, 12:58:19 AM by j.w.forrest »
Logged

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Reed Tools
« Reply #13 on: February 28, 2010, 11:07:38 PM »

I have got some home made tools which I've been using, but I want to take things up a gear with some better ones. Any pictures or opinions on making them would be greatly received.

I have devised a lifting tool out of (necessity and desperation) which works well, and is easy to make. I cut a slim strip of .001" brass shim stock about 2"-3" long with a slight taper. I bend a short fold about 1/16" on the narrower end. By plunging this past the side of the reed tongue near its tip, the reed can then be fished thru the plate. Once retrieved, then a support can be slid in place and the shim removed. (Three hands are quite useful here)! The brass shim, because of its thin-ness, offers little difficulty with the clearance between reed and slot, and won't damage the steel reed in any way. One must take care to examine the fold on the shim periodically, because it will eventually break and might leave a small flake of brass in the underside of the reed chamber, which would be a PITA. I've found that I can use one dozens of times before making a new one.

A picture would be much appreciated.
Logged

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Reed Tools
« Reply #14 on: March 01, 2010, 01:02:05 AM »

A picture would be much appreciated.

Here's some quick snaps that ought to explain how it works. BTW, the brass material I am using measures .002", not .001" as I stated earlier. When I made up this tool just now, I noticed that the .001" stock is too flimsy, and I miked my original tool to verify. This seems to clear all of the reed slots that I have messed with, (mostly Hohners). Best to proceed with caution in unknown territory. Things do get tighter up the scale with the little reeds, though. The use of the fold allows the shim to be pulled out if anything jams. Should take very little effort to lift the reed, unless the reeds are unusually stiff.

   revised link:        http://flickr.com/gp/47089974@N02/oF8foe
« Last Edit: March 01, 2010, 09:29:41 AM by j.w.forrest »
Logged

old geezer

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 241
  • Hohner Melodeon
Re: Reed Tools
« Reply #15 on: March 01, 2010, 06:04:01 AM »

A picture would be much appreciated.

               http://www.flickr.com/photos/47089974@N02/sets/72157623404997347/

I'm unable to go to this link for some reason...

are others having the same difficulity ??  ???
Logged
Jack Murphy    beyond the black stump

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Reed Tools
« Reply #16 on: March 01, 2010, 08:03:45 AM »

The album needs to be set for public view as it says it's private!
Logged

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Reed Tools
« Reply #17 on: March 01, 2010, 09:32:21 AM »

The album needs to be set for public view as it says it's private!

   My apologies....I thought I had this photo site figured out..... :P  try this link:

                                 http://flickr.com/gp/47089974@N02/oF8foe

Logged

acctech

  • Member
  • *
  • Offline Offline
  • Posts: 49
  • Crazy for free reeds!
    • Limex USA
Re: Reed Tools
« Reply #18 on: March 07, 2010, 05:00:25 AM »

Hohner USA has the brass tools for pulling the inside reed tongues out available in 2 guages for $2.78 each. They work fine, one of several techniques to access the inside reed.
Logged
Professional Accordion Technician since 1999
Diatonic accordions of all kinds! Piano accordion too :-)
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal