Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: clacking action, paolo soprani  (Read 3953 times)

0 Members and 1 Guest are viewing this topic.

chrisstevens

  • Member
  • *
  • Offline Offline
  • Posts: 16
clacking action, paolo soprani
« on: February 17, 2010, 06:28:16 PM »

recently acquired a lovely old paolo soprani button accordion...every now and then, i'll get an sudible clack from the right hand keyboard, and upon closer inspection, it is the sides of buttons clacking against the metal keyboard faceplate (there is a little bit of space between the buttons and the edge of the holes through which they poke, and some of the buttons have some wiggle to them).  coming from the world of concertinas, my first instinct would be to install a felt bushing pad, with button holes cut out, on the reverse of the keyboard faceplate...does anyone have any other ideas?
Logged

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: clacking action, paolo soprani
« Reply #1 on: February 17, 2010, 08:23:14 PM »

Perhaps that's why we see Tony MacMahon playing on a Soprani sans keyboard plate in old videos!
Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18

waldoB

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 126
Re: clacking action, paolo soprani
« Reply #2 on: February 18, 2010, 08:39:23 AM »

With a flat enclosed keyboard it is common to have small squares of thickish felt (CGM) , slightly wider than the narrowest point between the buttons, glued to the underside of the keyboard. This prevents lateral movement of the buttons, and easier to do than bushings. DB
Logged

boxlad

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 291
    • Ray Ó Díomasaigh
Re: clacking action, paolo soprani
« Reply #3 on: February 18, 2010, 09:24:27 AM »

I've seen the old footage of MacMahon playing without a keyboard and it is actually quite difficult if you try it on an old grey as the buttons are small and far apart. There is no room for error and your fingers will fall in between if you get it wrong. It is also nearly impossible to slide fingers from button to button without the keyboard in place. Any of his new recordings have significant button and keyboard noise. I've spoken to many repairers and the belief seems to be that bushings etc might lessen the noise but it is nearly impossible to eliminate it completely at least in an old grey Paolo. A small con when you consider all the pros of such a box!
So back to the original post...bushings would appear to be a good option in this case as suggested by WaldoB. 
Logged

Lars

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 797
Re: clacking action, paolo soprani
« Reply #4 on: February 18, 2010, 04:00:25 PM »

That old clip shows MacMahon playing a B/C box, not the D/D# we all associate him with.
Logged

LDbosca

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 674
Re: clacking action, paolo soprani
« Reply #5 on: February 18, 2010, 06:12:04 PM »

I've seen the old footage of MacMahon playing without a keyboard and it is actually quite difficult if you try it on an old grey as the buttons are small and far apart. There is no room for error and your fingers will fall in between if you get it wrong. It is also nearly impossible to slide fingers from button to button without the keyboard in place. Any of his new recordings have significant button and keyboard noise. I've spoken to many repairers and the belief seems to be that bushings etc might lessen the noise but it is nearly impossible to eliminate it completely at least in an old grey Paolo. A small con when you consider all the pros of such a box!
So back to the original post...bushings would appear to be a good option in this case as suggested by WaldoB. 

I'm not the biggest fan of Paolo's, I do like the sound of certain grey ones alright. Just wondering, by advantages I presume you mean the sound and playability?

chrisstevens

  • Member
  • *
  • Offline Offline
  • Posts: 16
Re: clacking action, paolo soprani
« Reply #6 on: February 19, 2010, 04:04:02 PM »

The felt bushing strips in between the buttons worked like a charm (and a quick, easy job too), thanks Waldo..

Only other action noise I can near now is the control arms on the inside row (nearest grille) contacting the pallet arms coming down from the top of the grille (two piece lever system for controlling the inside row's pallets).  it only really happens when i throw my fingers at the keyboard, but i tend to do this a lot.  it's non existent on the outside row because of the one piece levers.  it's a bit nit picky, but does anyone have any solutions for this?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: clacking action, paolo soprani
« Reply #7 on: February 19, 2010, 04:22:47 PM »

Only other action noise I can near now is the control arms on the inside row (nearest grille) contacting the pallet arms coming down from the top of the grille (two piece lever system for controlling the inside row's pallets).  it only really happens when i throw my fingers at the keyboard, but i tend to do this a lot.  it's non existent on the outside row because of the one piece levers.  it's a bit nit picky, but does anyone have any solutions for this?

Quietening that noise can be done but it involves bending the thinner wire part of the secondary lever to take up the play.  Its tricky to get right because I find its essential to separate the secondary lever from the primary one in order to do the adjustment, and its all to easy to widen the gap again when reassembling.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

chrisstevens

  • Member
  • *
  • Offline Offline
  • Posts: 16
Re: clacking action, paolo soprani
« Reply #8 on: February 19, 2010, 06:14:00 PM »

thanks theo, did it this morning and it worked like a charm....

i unscrewed the upper control arm strip, removed the rear keyboard faceplate so i could raise the inside row levers way up and out of the way, then wedged wooden splints in between those levers and the outside row levers to keep them elevated. pulled the upper control arm strip with it's pallets out, and squeezed all the small wires down considerably.  then slid the pallets back onto the levers just enough to keep them in place.  now i cut the wooden splints between each arm (so as not to rebend the wire part when pulling them back out), slid the pallets all the way on, and voila! quiet as a church mouse.

took me all of 30 minutes
Logged

boxlad

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 291
    • Ray Ó Díomasaigh
Re: clacking action, paolo soprani
« Reply #9 on: February 19, 2010, 06:41:40 PM »

Quote
Insert Quote
Quote from: Boxlad on Yesterday at 09:24:27 AM
I've seen the old footage of MacMahon playing without a keyboard and it is actually quite difficult if you try it on an old grey as the buttons are small and far apart. There is no room for error and your fingers will fall in between if you get it wrong. It is also nearly impossible to slide fingers from button to button without the keyboard in place. Any of his new recordings have significant button and keyboard noise. I've spoken to many repairers and the belief seems to be that bushings etc might lessen the noise but it is nearly impossible to eliminate it completely at least in an old grey Paolo. A small con when you consider all the pros of such a box!
So back to the original post...bushings would appear to be a good option in this case as suggested by WaldoB.  

I'm not the biggest fan of Paolo's, I do like the sound of certain grey ones alright. Just wondering, by advantages I presume you mean the sound and playability?

LD,
This has been discussed several times on this forum but yeah I mean the sound and power of the grey Paolo Soprani as being major plus factors. There are other boxes that are easier to play though. It's a matter of taste really! I see you are waiting for your French box to arrive. What made you go for the LMM set up?
« Last Edit: February 20, 2010, 10:25:29 AM by Boxlad »
Logged

Gandy

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 407
Re: clacking action, paolo soprani
« Reply #10 on: February 20, 2010, 10:23:50 AM »

The felt bushing strips in between the buttons worked like a charm (and a quick, easy job too), thanks Waldo..

Hi, could I ask you about that?  What glue did you use to stick the felt to the metal, and how far did you have the felt over hanging the metal?  Thanks.
Logged
Tony S

LDbosca

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 674
Re: clacking action, paolo soprani
« Reply #11 on: February 20, 2010, 03:56:49 PM »

LD,
This has been discussed several times on this forum but yeah I mean the sound and power of the grey Paolo Soprani as being major plus factors. There are other boxes that are easier to play though. It's a matter of taste really! I see you are waiting for your French box to arrive. What made you go for the LMM set up?

I was originally going for the MMM tuned relatively dry but a few things influenced me. Listening to "Spicatto Junction" by Mairtin O'Connor and the Contempo string quartet there's some lovely stuff with one low and middle reed on, a real classical accordion sound. I'm also into my musette and manouche a bit so being able to switch registers between parts would be nice, there's usually enough time to do so and enough contrast between parts to make it a nice addition. Playing on the low reed and moving up the octave gives a nice mellow effect, stuff like that. Plus, after borrowing an LMM box for a week I got used to an instrument with serious BALLS for trad! (which are also the selling point of those Paolos and the old Walters and that I suppose)

chrisstevens

  • Member
  • *
  • Offline Offline
  • Posts: 16
Re: clacking action, paolo soprani
« Reply #12 on: February 24, 2010, 02:53:06 PM »

Hey Tony - I went to the hardware store and bought the small self sticking felt sheets used on the bottom of furniture, etc. The medium duty brown sheet works the best and cost all of $3.

Cut strips about 1/4" wide and half an inch long. They should hang over the edges of the fingerholes just barely, the buttons should just barely touch them, or not even touch. Test fit and trim with a razor. 
Logged

Gandy

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 407
Re: clacking action, paolo soprani
« Reply #13 on: February 24, 2010, 04:40:47 PM »

Cheers, I'll look for that stuff.   I notice that the finger board on mine clearly used to have something glued to the underneath. 

I was wondering about gluing a sheet over the whole surface, then punching out the hole - depends on whether I've got punch the right size, but I thought if it was a snug fit in the hole in the metal work, then the hole in the felt would be a touch smaller corresponding to the wall thickness of the punch.    On the other hand maybe gluing strips between the rows makes more sense, and is a bit easier to try on a small scale.
Logged
Tony S
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal