Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Bass Reed & Tiny Reed Sounding Problems  (Read 5348 times)

0 Members and 1 Guest are viewing this topic.

suesqueezer

  • Member
  • *
  • Offline Offline
  • Posts: 16
  • Piana accordion player now attempting all buttons!
Bass Reed & Tiny Reed Sounding Problems
« on: March 11, 2008, 02:16:43 PM »

Hello there everyone. Restoring and old thirties Suprema A/D box. I've just replaced the leathers (real) on the individual reed blocks, waxed them in an now hearing a reed, (on all, on the push OK, but on the pull it has a rushing air sound and then the note is audible but weak. I tuned up the chord reeds, reglued the existing leathers and rewaxed them in, no problems there. Can it be the leathers I've installed? Also, a question for clearing obstructed tiny reeds - other than pinging it and bending back and forth (which I have done) any suggestions?
Logged

BruceHenderson

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 262
Re: Bass Reed & Tiny Reed Sounding Problems
« Reply #1 on: March 11, 2008, 02:42:11 PM »

Hello there everyone. Restoring and old thirties Suprema A/D box. I've just replaced the leathers (real) on the individual reed blocks, waxed them in an now hearing a reed, (on all, on the push OK, but on the pull it has a rushing air sound and then the note is audible but weak. I tuned up the chord reeds, reglued the existing leathers and rewaxed them in, no problems there. Can it be the leathers I've installed? Also, a question for clearing obstructed tiny reeds - other than pinging it and bending back and forth (which I have done) any suggestions?

   Your issue on the larger reeds sounds like a leak.  You may have a leak around the wax, or a leak could exist anywhere else.  Unfortunately, the sound of a reed with bad leathers can sound exactly the same.  So, I couldn't do any more than a WAIG on that one.
   On the tiny reeds, you should find some "shim stock".  This is thin metal sheet about 8 thousands (or 1/5 of a millimeter) thick.  You can *very* gently lift the tip of the reed and slip the shim under it.  That will clear any obstruction and support the reed if you have to clean the edges (with a small scraper, etc.).  I'm a little wary of "pinging it and bending it back and forth" -- I'm guessing you know that the tip of the reed must sit in exactly the right place to properly "speak"; if it gets bent either higher or lower than the "perfect spot", it won't start easily and it will sound bad. 
   On another issue, the reed must be centered in the reed frame -- the space between reed and the frame must be the same all the way around and must be the correct clearance.  Using the shim stock can help on this, too; slip a thin sliver of the shim all around the reed.  Needless to say, anything on the sides or tip of the reeds that shouldn't be there can cause real problems.  This can be dirt and dust, scum from the instrument being played in smoky places, rust, and other similar contaminants.  Anything on the side of the reed that is causing the be "obstructed" should be carefully removed.  But be sure that the sharp edges on the reeds and the reed frames aren't damaged.
   Good luck, BH
Logged
I love one-rows!  Four reeds kick butt!!!!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Bass Reed & Tiny Reed Sounding Problems
« Reply #2 on: March 11, 2008, 03:11:08 PM »

A 10x hand lens, or a low power binocular microscope can be very useful for getting a detailed look at the reed tongue.  Look for glue squeezed out from under the valves and onto the edge of the reed,  reed set too high, or reed tongue coming into contact with the sides of the slot.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

suesqueezer

  • Member
  • *
  • Offline Offline
  • Posts: 16
  • Piana accordion player now attempting all buttons!
Re: Bass Reed & Tiny Reed Sounding Problems
« Reply #3 on: March 11, 2008, 08:20:37 PM »

Thanks guys for the input. Regarding the verry thin metal shims - where or what from can I obtain some of these?
The leak issue - could it really be around wax - ? It seems they are all on the one direction leaking air before the weak tone sounds. I decided to remove all and then I rewaxed one pair and still the same thing.
Logged

sCANdanADIAN

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 181
Re: Bass Reed & Tiny Reed Sounding Problems
« Reply #4 on: March 11, 2008, 09:11:33 PM »

Princess Auto or Canadian Tire might have some mechanics tools that would work.I believe that they're called 'feeler gauges',they look like a folding pocketknife with various gauges of metal shims that fold out to test gap thicknesses.

Sue,I hope to be as brave as you someday.I've noticed that concertina.net has a lot of technical information regarding tuning,waxing riveting etc...I'm guessing that concertinas are way more delicate and tempermental than the humble but sturdy melodeon.

Chris
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Bass Reed & Tiny Reed Sounding Problems
« Reply #5 on: March 11, 2008, 11:45:10 PM »

Thanks guys for the input. Regarding the verry thin metal shims - where or what from can I obtain some of these?

A piece of stiff paper will do the job of supporting the reed.  The shim material is more durable, but if you have only one problem reed paper will do fine.  If you do want metal then use a sharp pair of scissors to cut a piece out of the side an aluminium drink can, then flatten it out.  Smooth the edges on abrasive paper to lessen the risk of cutting fingers.

Aluminium or brass is much preferable to steel.  They are softer and make it less easy to do damage to the reed.
« Last Edit: March 11, 2008, 11:46:54 PM by theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

suesqueezer

  • Member
  • *
  • Offline Offline
  • Posts: 16
  • Piana accordion player now attempting all buttons!
Re: Bass Reed & Tiny Reed Sounding Problems
« Reply #6 on: March 12, 2008, 03:43:23 AM »

Aluminium or brass is much preferable to steel.  They are softer and make it less easy to do damage to the reed.
[/quote]

Thanks Theo, Gonna fashion me some little shim tools from a can - that fits my budget!
Logged

JD

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 235
Re: Bass Reed & Tiny Reed Sounding Problems
« Reply #7 on: March 12, 2008, 10:09:42 AM »

the side an aluminium drink can, then flatten it out.[/quote]

Out of curiosity, how thick is the wall of an ali drinks can? I ask because a book I have on concertina maintenance suggested sliding a 1.5 thou feeler gauge down the side of a reed tongue as a possible cure for a slow-speaking reed. It worked for me. Is a can wall really that thin?
Logged

Larry Anthony

  • Good talker
  • **
  • Offline Offline
  • Posts: 68
Re: Bass Reed & Tiny Reed Sounding Problems
« Reply #8 on: March 12, 2008, 12:23:25 PM »

the side an aluminium drink can, then flatten it out.

Out of curiosity, how thick is the wall of an ali drinks can? I ask because a book I have on concertina maintenance suggested sliding a 1.5 thou feeler gauge down the side of a reed tongue as a possible cure for a slow-speaking reed. It worked for me. Is a can wall really that thin?
[/quote]

On my metric micrometer a beer can measured 0.12mm, which I think equates to approximately 0.005 inches.  Which makes it very suitable for the job.
Logged

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: Bass Reed & Tiny Reed Sounding Problems
« Reply #9 on: March 12, 2008, 01:20:47 PM »

The cans we have in Canada might be thicker than those in other countries... A feeler gauge is really inexpensive and probably a better option.

Sue: Check out the car tools in Canadian Tire or Parts Source, I bought one of those feeler gauges years ago, and it has blades that are very very thin and would be ideal for your reed work.
Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18

Larry Anthony

  • Good talker
  • **
  • Offline Offline
  • Posts: 68
Re: Bass Reed & Tiny Reed Sounding Problems
« Reply #10 on: March 12, 2008, 01:53:31 PM »

The cans we have in Canada might be thicker than those in other countries... A feeler gauge is really inexpensive and probably a better option.

Sue: Check out the car tools in Canadian Tire or Parts Source, I bought one of those feeler gauges years ago, and it has blades that are very very thin and would be ideal for your reed work.

But as theo has pointed out, you are less likely to do any damage with aluminium.  Remember, the reed plates are usually quite soft compared to hardened feeler gauges
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Bass Reed & Tiny Reed Sounding Problems
« Reply #11 on: March 12, 2008, 02:35:12 PM »

... A feeler gauge is really inexpensive and probably a better option.

Probably better?  in what way? 

In my experience the best material for a reed support tool is actually phosphor bronze.  It is about the springiest, and therefore most supporting material while at the same time not being hard enough to damage aluminium reed plates.  The one I use is made specially for the purpose by Hohner.  I didn't mention this earlier as its not a material that is easily available.  If you need something thinner than the .005" of a drinks can, so you can get up near the root of the reed, then a decent quality paper is preferable on the grounds of being much less likely to deform the edge of the reed, or the slot in the reedplate.  Postit Notes are what I usually use, because they are easily available, and the paper quality is good - they don't easily shed fibres at the edges.

Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: Bass Reed & Tiny Reed Sounding Problems
« Reply #12 on: March 12, 2008, 06:20:35 PM »

... A feeler gauge is really inexpensive and probably a better option.
Probably better?  in what way? 
Well, for beer cans at least, the ones we get from UK are much thinner than our local production! The metal might be too thick.
The feeler gauge I have has its very thin blades made from brass.

Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal