Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Why#?  (Read 2362 times)

0 Members and 1 Guest are viewing this topic.

HallelujahAl

  • Guest
Why#?
« on: April 13, 2010, 08:35:09 PM »

Had a bit of time off these last couple of days and so I finally got around to tuning a load of old reeds - why is it that the vast majority of the old reeds had gone sharp and needed bringing back down to pitch? Its a problem I've often noticed - even with concertina reeds as well. Why # and not b?
Can someone enlighten me as to the physics of the matter?
Thanks, AL.
Logged

Gandy

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 407
Re: Why#?
« Reply #1 on: April 14, 2010, 08:49:19 AM »

Sort of related, but I wonder why new reeds are supplied tuned sharp.   To an outsider it seems that filing from the tip to sharpen a reed does less damage than filing the root to flatten it - if that is truly the case then I wonder why they're not supplied a little flat.
Logged
Tony S

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Why#?
« Reply #2 on: April 14, 2010, 09:01:42 AM »

I don't think they "went sharp" Al - they were probably tuned that way. I've often heard 19th C concertinas referred to as being in the "old, high" pitch. I don't know when A=440 became standard.
A=440 became the international standard pitch reference in 1939
http://en.wikipedia.org/wiki/Pitch_(music)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Why#?
« Reply #3 on: April 14, 2010, 09:12:58 AM »

Sort of related, but I wonder why new reeds are supplied tuned sharp.   To an outsider it seems that filing from the tip to sharpen a reed does less damage than filing the root to flatten it - if that is truly the case then I wonder why they're not supplied a little flat.
In my experience of tuning reeds (admittedly fairly limited), I find it is easier and I have much more control on flattening a reed than sharpening it.

To flatten a reed, I use a reed scratcher to gently remove steel from the area about 1/3 of the way from the root (rivet) end. I don't file this area; I can keep the reed scratcher away from the edges of the steel tongue.

When sharpening a reed by filing the tip, I find that far more care is needed (a) to keep the file flat over the tip area in order ensure that steel is removed evenly across the width of the tongue and (b) the effect of sharpening seems to be much more sensitive - removing a tiny amount of steel will have a more pronounced effect on the pitch, compared with flattening.

It is also easier to flatten the underneath (pull) reeds than it is to sharpen them. To flatten them you can use the reed scratcher through the reed plate slot, whereas to sharpen them you need to use a reed lifter to raise the steel tongue through the reed plate slot first.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Larry Anthony

  • Good talker
  • **
  • Offline Offline
  • Posts: 68
Re: Why#?
« Reply #4 on: April 14, 2010, 12:03:41 PM »

Could it be that the steel has become work/age hardened? This would raise the pitch.
Logged

HallelujahAl

  • Guest
Re: Why#?
« Reply #5 on: April 14, 2010, 12:29:22 PM »

Quote
Could it be that the steel has become work/age hardened? This would raise the pitch.

I'm thinking along those lines - perhaps a build up of rust and sediment etc would affect the reed's pitch, usually making the tip have less metal & muck than the base of the reed and hence raising pitch?
Logged

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Why#?
« Reply #6 on: April 14, 2010, 02:43:07 PM »

Can't prove it I suspect age, and particularly usage would tighten the metal grain boundaries and should tend to stiffen a reed. Eventually it'll crack of course. Has anyone noticed a reed going sharp just before it snaps though?  (I didn't).

The other main frequency determnant is mass, and it would take eons for the metal molecules to evaporate enough to affect that. LdT comes from Gallifrey and so might be able to enlighten us on that one. ;)
Logged
  _       _    _      _ 
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal