Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Bellows Pins  (Read 3577 times)

0 Members and 1 Guest are viewing this topic.

Ollie

  • Grumpy Young Git
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1900
    • Ollie King
Bellows Pins
« on: April 14, 2010, 10:42:07 PM »

Slight problem... my bellows pins keep coming out whilst I'm playing. Not fully, but it is noticeable and the instrument takes on more air. What can I do to stop this? Do I need new pins?

Also, occasionally, my air button doesn't shut properly. Any ideas?
Logged
Hohner Erika 12 bass D/G : Hohner Erika Bb/Eb : Hohner 1 row 4 stop D : Hohner Erica 9 bass D/G :

http://www.olliekingmusic.com/

Free-Reed Specialist, Hobgoblin Leeds

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Bellows Pins
« Reply #1 on: April 14, 2010, 10:53:32 PM »

Crude but effective alert!

Take out the pins, put them in a pair of electricians pliers in the wire cutting bit, squeeze gently to form a ridge, reinsert by gently tapping them in.

I know; but I did say crude but effective and works for me  ;D

Andy Simpson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 938
Re: Bellows Pins
« Reply #2 on: April 14, 2010, 11:12:09 PM »

Is this the Pokerwork you've just stripped the finish off?. If you haven't sealed or refinished the wood then I'd guess that both problems are down to the casework moving due to now being susceptible to changes in humidity and right now is a bad time for that sort of thing.

What Lester said for the pins and for the air button, assuming the mechanism isn't jamming in some way due to rust or buildup of grime and dust or the spring's about to go and isn't exerting enough pressure, then you could try removing the pallet and regluing it with a hot melt glue gun to give a bit of flex.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Bellows Pins
« Reply #3 on: April 14, 2010, 11:24:38 PM »

I advise caution with Lesters suggestion.  It will work in the short term but will eventually make the problem worse because the roughened surface of the pins will gradually enlarge the holes.  A small patch of tape over the pin is also effective and may not be pretty but is also effective and safe. 

Another fix us to replace the bellows gasket,  new gasket material will put more pressure on the pins and tend to hold them in place.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

RGF

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 214
Re: Bellows Pins
« Reply #4 on: April 15, 2010, 05:43:46 AM »

I have also had success with something sold here (U.S.) by the brand name of "UHU Glu Wood Joint Tightener". It's purpose is for the repair of loose wood joints, as in chair spindles, etc. I think it works, in part, by causing a permanent expansion of the wood fibers. I remove the pins and use a tiny brush to swab the bores of the holes, and let it do its work. On reassembly, the fit of the pins is noticeably tighter. This, along with new bellows tape, has worked well for me.

Bob
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Bellows Pins
« Reply #5 on: April 15, 2010, 07:16:22 AM »

I advise caution with Lesters suggestion.  It will work in the short term but will eventually make the problem worse because the roughened surface of the pins will gradually enlarge the holes. 

Did come with a bodge warning   (:)

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Bellows Pins
« Reply #6 on: April 15, 2010, 03:16:00 PM »

Bitof masking tape over them will hold them for a bit and won't damage the finish (:) If it is something to do with stripping it off and humidity and so on then best to refinish it, let the wood stabilise and then see whether they are still loose.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Bellows Pins
« Reply #7 on: April 20, 2010, 06:10:43 PM »

My advice would be as follows: Remove your pins, put a drop of water in all the holes of both the casings and the frames and let it dry. Replace the pins.
Most accordion technicians have pins in different thicknesses, so that might be another option, albeit more expensive...
Logged

Ollie

  • Grumpy Young Git
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1900
    • Ollie King
Re: Bellows Pins
« Reply #8 on: April 20, 2010, 06:18:04 PM »

Thanks for all the replies. I think Andy is right, humidity has been affecting it. I was playing away in the glorious sunshine at the weekend, and I didn't have a problem, but they were popping out all the time when I was playing in the freezing cold at Morris practise on Wednesday. I've yet seal the box properly, so if it is still a problem after that, I'll try some of the above suggestions.

Air button was less of a problem; turned out the button itself was rubbing against the hole. A quick sand on the inside of the hole soon sorted that one out.
Logged
Hohner Erika 12 bass D/G : Hohner Erika Bb/Eb : Hohner 1 row 4 stop D : Hohner Erica 9 bass D/G :

http://www.olliekingmusic.com/

Free-Reed Specialist, Hobgoblin Leeds

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: Bellows Pins
« Reply #9 on: April 20, 2010, 08:00:46 PM »

A bit of reed wax or violin rosin can help holding them in place!
Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18

old geezer

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 241
  • Hohner Melodeon
Re: Bellows Pins
« Reply #10 on: April 21, 2010, 08:17:48 AM »

A bit of reed wax or violin rosin can help holding them in place!

or PVA glue in the inner holes and, leaving it over-nite to dry, before re-assembly  ;)
Logged
Jack Murphy    beyond the black stump

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Bellows Pins
« Reply #11 on: April 21, 2010, 08:42:34 AM »

Wood is funny stuff! I used to give my pins a tweak with pliers and that was OK for my original Hohner. In retrospect it probably brused the wood and made a temporary problem permanent. If it really is due to swing in humidity I suspect the old furniture trick of waxing might be right - will use it next time.

btw: special problem on my Gaillard - Bertrand's used clever pins that seem to be made of thin but very resiliant steel. Problem is that they have a double head with a grove so an extractor doesn't bruise the wood. But the moment I played it wearing wool - this quietly entangled in the fibre and when I got home 2 were missing!

Thanks for the tips for what is a perenial problem in our trade  :||:
Logged
  _       _    _      _ 

Malcolm Austen

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 495
  • any old hohner
Re: Bellows Pins
« Reply #12 on: April 22, 2010, 05:36:58 AM »

Bitof masking tape over them will hold them for a bit and won't damage the finish

If left for a short time this is true but if masking tape is left for a long time it can be very difficult to remove the residue.
Logged
aka malodeon
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal