Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Italian reeds in a pokerwork  (Read 1933 times)

0 Members and 1 Guest are viewing this topic.

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Italian reeds in a pokerwork
« on: April 20, 2010, 12:33:20 PM »

I'm thinking of putting a set of italian reeds in an old G/C pokerwork that has rusty reeds.  If I keep the same tonality G/C will it involve major reworking of the blocks or do they fit fairly well with minor modification?  Any insight on this will be much appreciated.

thanks
Michael
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Italian reeds in a pokerwork
« Reply #1 on: April 20, 2010, 01:55:14 PM »

Italian reeds tend to be a bit longer than Hohner reeds of the same pitch, BUT not all Italian reeds are the same.  Its a bit like asking "I'm replacing my British car with a European one, will it fit in my garage?"  If you can find someone who has done the same swap with the same make and quality of reeds then you should get a definitive answer.   I have not fitted any Italian G/C reeds to a Hohner but my guess is that you may have to lengthen some of the treble reed chambers by carving some wood out of the top of the chamber.  Chord reeds should fit straight on.   For the bass reeds you will need to reduce the width of the reed chambers, as Hohner bass reed plates are very wide compared to Italian.  Italian bass reed plates tend to be thicker too, so you may have a clash of rivet heads between bass and chord blocks.  You can get round this by filing some metal of the rivet heads and/or moving the reedblocks slightly further apart.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Italian reeds in a pokerwork
« Reply #2 on: April 20, 2010, 03:00:18 PM »

Thankyou Theo.....exactly the kind of information I was looking for.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Italian reeds in a pokerwork
« Reply #3 on: April 20, 2010, 04:25:04 PM »

Of course you could just clean up the Hohner reeds,  probably less work than adapting the Italian ones, and without the expense of a new set of reeds.  Rust on reeds often looks much worse than it is.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: Italian reeds in a pokerwork
« Reply #4 on: April 20, 2010, 07:52:36 PM »

I changed reeds in two boxes from Hohner to Cagnoni Macchina, and in both cases the reedblocks had to be modified, as the italian reed plates were narrower, thicker and longer. Be prepared to do some precision woodworking in order to extend the blocks and/or fill gaps in order to accommodate the narrower plates.

Of course, after the change, the boxes did not have the Hohner sound anymore! The new reeds sound brighter and punchier, but the basses lack the Hohner grunt.
« Last Edit: April 20, 2010, 07:54:34 PM by québécois »
Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal