Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: plastic paint to strengthen paper bellows joints and gussets  (Read 13419 times)

0 Members and 1 Guest are viewing this topic.

Kautilya

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 977
plastic paint to strengthen paper bellows joints and gussets
« on: April 22, 2010, 04:54:45 PM »


(whether acrylic or another 'plastic paint' can be used to strengthen, reinforce splitting from inside or also outside (to give a fresh look to) bellows

Painting on paper with acrylic.
Gary Smith (talking about paper preparation for painting with oils to get long life of painting):
The secret to painting on paper and preparing less expensive papers lies in the wonder of the acrylic medium. Acrylic, is essentially a plastic in liquid form. When it dries, and it dries so fairly rapidly, it forms a highly resistant and protective layer of plastic. It also has excellent adhesive qualities, which makes it suitable for a number of painting and preparing purposes.

All that is required are a number of layers of thin acrylic paint or medium on the paper. Three layers should be sufficient, allowing each layer to dry before applying the next. The texture that you might like to create will be determined by the amount of acrylic paint or medium you apply.
….The acrylic paint and medium is basically a layer of plastic that protects the surface against penetration from oil and other elements. Acrylic medium also strengthens the paper. This is the reason why relatively cheaper paper can be used with this method. However, remember that we are still dealing with paper and there are limits to its strength and flexibility.

and??
http://www.polymarine.com/products/parts-and-accessories/flexible-paints-and-antifoulings/superflex-pvc-paint/index.cfm
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: plastic paint to strengthen paper bellows joints and gussets
« Reply #1 on: April 22, 2010, 05:06:31 PM »

If the bellows are splitting I think any sort of surface coating is only going to be a temporary treatment.  But if the bellows are splitting and the only other choice is replacement then you have nothing to loose except the cost of the acrylic.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: plastic paint to strengthen paper bellows joints and gussets
« Reply #2 on: April 22, 2010, 06:32:21 PM »

The best thing for bellows splitting on the folds, is to fix from the inside with some flexible heavy paper. Fold the card so you have a new fold and glue in place with the fold flush with the existing one. General PVA is fine for this as the glued surfaces aren't under stress or movement. Cover with new bellows tape and you cant even tell it was split!
Logged

HallelujahAl

  • Guest
Re: plastic paint to strengthen paper bellows joints and gussets
« Reply #3 on: April 22, 2010, 06:38:34 PM »

I use an adhesive linen to repair from the inside. The glue is activated by water. It's used by quality bookbinders. But I don't buy this stuff from UK as it's expensive. I ship it in from the US where it's REALLY cheap. In fact I've thought about importing it and making a killing! It forms the hinges for my sets of concertina bellows - is strong, airtight, and real neat!
AL
Logged

Kautilya

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 977
Re: plastic paint to strengthen paper bellows joints and gussets
« Reply #4 on: April 22, 2010, 06:42:01 PM »

If the bellows are splitting I think any sort of surface coating is only going to be a temporary treatment.  But if the bellows are splitting and the only other choice is replacement then you have nothing to loose except the cost of the acrylic.
But will still be stuck with my chains! (no workers of the world electoral references on melnet!)
On a lighter note (I know u already reacted to an earlier one on this) I wondered if anyone had actually tried it is as a preventive technique, e.g. when tarting up the look of the bellows (all that gusset corner dust etc).

Accepting normal inside splitting repair procedure, I am thinking of the wearing out stage rather than the final splitting stage.....

Dupont seem to be the main makers of this type of elastomer stuff and although they have (as of April 20 2010......) stopped making their Hypalon, there is another 'lettering paint which 'renovates' - in other words, if it is a canvas bellows it would strengthen the fabric skeleton weave ........ further, Polymarine thinks it should work for paper not just canvas.  It may depend on whether,, e.g. an old German 'paper' bellows it of paper made from rags etc which are essentially making a paper from a mash of fibres (as opposed to cellulose paper from trees???) Handmade papers are clearly a mish-mash weave as u can see the fibres.

http://www.polymarine.com/products/parts-and-accessories/flexible-paints-and-antifoulings/letterflex-pvc-lettering-paint/index.cfm

Will have a go on an old bellows and see what emerges - if it adds 20 years to the 'fabric' I will surely by then be playing one of your harps O doG, so wont be able to report back............... >:E >:E
Logged

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: plastic paint to strengthen paper bellows joints and gussets
« Reply #5 on: April 22, 2010, 08:31:03 PM »

I once had an old Koch one row that was quite nice, save for the bellows gussets that were dotted with tiny holes, perhaps it had been on the menu for some discriminating insects. I was able to make a repair of sorts using a product which is billed as a liquid electrical tape made by Starbright
     It was necessary to remove the bellows and stretch them using clamps and a couple of sticks to keep them extended, and then painting the stuff in two separate thin coatings over the porous areas inside the bellows.
:-X Word of caution here: this product contained some very nasty solvents and should be used outdoors or under a ventilating hood!  :-X

 This was purely a last ditch repair, and it rendered the bellows reasonably airtite and quite playable.
« Last Edit: April 23, 2010, 12:41:04 AM by j.w.forrest »
Logged

Kautilya

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 977
Re: plastic paint to strengthen paper bellows joints and gussets
« Reply #6 on: April 26, 2010, 08:53:48 PM »

Did you get a good kick when you put on your ventilating hood??!!

[Update (some useful tips also coming in from tina players]

Gave up on Dupont for materials including useless calls to their Euro HQ in Spain - totally disorganised with no-one knowing who does what on paints in their technical divisions- the man at Stevenage paint division has moved.......

However -plus ca change... taking us back to leather cream of old standby, a discussion with the manager of Broodie & Middleton/ (which also Russell & Chapple) suppliers to "artistes" (paint ones!) was that acrylic would not last, BUT a product called MAGIX for restoring distresssed leather (with colours too), was very flexible.

Maybe this could work also on paper bellows, praps. One problem is that it comes in 150ml aerosols with a solvent and dries very fast so the question is whether it will stay wet enough when sprayed into a pot for then brushing on.... B&M only have four colours (incl b&w!) in stock but the (uknown manufacturer, perhaps French - tho could be KIWI shoe polish Co. which is owned by Sara Lee) MAGIX range shows up in France as having 58 different colours.

As part of the exercise is to tart up as well as stabilise the material, that range of colours sounds v good... if it works. Including chocolate, cognac, London and violine....which aint violon I assume...
 http://www.cuirs-pratique.com/cuirs-ameublement_reteindre_teinture-finition-spray-bleu-ciel-p-780.html

it is 8 quid in Covent Gdn shop of B&M and I see an importer in L'pool at about five quid plus delivery.

Logged

Tony M

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: plastic paint to strengthen paper bellows joints and gussets
« Reply #7 on: April 27, 2010, 01:12:47 PM »

I use an adhesive linen to repair from the inside. The glue is activated by water.  . . .  It forms the hinges for my sets of concertina bellows - is strong, airtight, and real neat!

At the risk of straying into a subject more appropriate to another forum . . .
I picked up a Gallotta concertina recently, on which the "leather" strips along the length of the bellows were made of some kind of plastic-backed cloth.  The plastic, inevitably, had disintegrated, so the bellows, which are otherwise pretty good, leaked like a sieve.  I went over the leaky "cloth" bits with diluted PVA (with the bellows stretched, as described by J.W.Forrest) and, after a couple of coats, the thing is playable (more or less). 

The downside is that the flexibility was reduced - however, a couple of treatments with ArmorAll vinyl treatment has restored this aspect a bit.  I'd like to make the thing properly airtight - having re-valved it and done a basic tune, I think it will make a nice enough instrument - but I recognise that it is what it is - and that it isn't worth much, in financial terms.

The question is, where to go next.  I'm considering stripping the bellows and replacing the defective lining with leather - if I do that, I'll need to re-do the "bellows tape" strips around the bellows (I'm sure there are proper names for these, but I don't know what they are), and the joints to the ends and intermediate frames - and if I use decent leather for all that, I'll be spending about 50% more than I paid for the instrument, and probably more than it's worth.

I wondered whether the linen you describe could be used, on the inside of the bellows, over the joints that the lining should seal (rather than on the folding joints).  Do you think it would have sufficient flexibility?  Fitting would be tricky, but not impossible, and properly airtight bellows would be a big improvement.

Thoughts and suggestions welcome!

Regards,

Tony.
Logged

Tony M

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: plastic paint to strengthen paper bellows joints and gussets
« Reply #8 on: April 27, 2010, 06:39:13 PM »

If you're doing this up only to sell it on then   .  .  .

No, my tinkering isn't based on selling things on (although my dear wife's patience may wear thin if I don't eventually shed a few of my "projects").

I started tinkering with accordions, and (I think) I can do a reasonable job of revalving and waxing.  I've ventured to tune one, and it worked out passably well.  I suppose I just keep an eye out for something appealing as a next project - the concertina was one, and there are a couple more waiting to be "got around to". 

The point about cost was, I suppose, simply to say that I'd rather not spend excessively on it.  I know that, if I completely rebuild the bellows, it'll be much better than it ever was - but it's not as if it was ever going to be of such value that "doing a proper job" was the obvious and appropriate way to go.  Not sure where the balance lies - so if there's a less expensive way to achieve air-tightness, it's worthy of serious consideration!

Tony
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: plastic paint to strengthen paper bellows joints and gussets
« Reply #9 on: April 27, 2010, 09:14:49 PM »

You can get all the leather components from David Leese at concertina-spares.com
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Kautilya

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 977
Re: plastic paint to strengthen paper bellows joints and gussets
« Reply #10 on: April 28, 2010, 07:32:52 PM »

I use an adhesive linen to repair from the inside. The glue is activated by water.  . . .  It forms the hinges for my sets of concertina bellows - is strong, airtight, and real neat!

At the risk of straying into a subject more appropriate to another forum . . .
I picked up a Gallotta concertina recently, on which the "leather" strips along the length of the bellows were made of some kind of plastic-backed cloth.  The plastic, inevitably, had disintegrated, so the bellows, which are otherwise pretty good, leaked like a sieve.  I went over the leaky "cloth" bits with diluted PVA (with the bellows stretched, as described by J.W.Forrest) and, after a couple of coats, the thing is playable (more or less). 

The downside is that the flexibility was reduced - however, a couple of treatments with ArmorAll vinyl treatment has restored this aspect a bit.  I'd like to make the thing properly airtight - having re-valved it and done a basic tune, I think it will make a nice enough instrument - but I recognise that it is what it is - and that it isn't worth much, in financial terms.

The question is, where to go next.  I'm considering stripping the bellows and replacing the defective lining with leather - if I do that, I'll need to re-do the "bellows tape" strips around the bellows (I'm sure there are proper names for these, but I don't know what they are), and the joints to the ends and intermediate frames - and if I use decent leather for all that, I'll be spending about 50% more than I paid for the instrument, and probably more than it's worth.

I wondered whether the linen you describe could be used, on the inside of the bellows, over the joints that the lining should seal (rather than on the folding joints).  Do you think it would have sufficient flexibility?  Fitting would be tricky, but not impossible, and properly airtight bellows would be a big improvement.

Thoughts and suggestions welcome!

Regards,

Tony.
Useful grist to the glue-pot.
A bow first to the professionals who do repairs day in day out. They have to earn a decent living and pay the bills and fortunately they all seem overwhelmed with work as they have queues and queues which is wonderful.

Obviously it is the labour cost which makes up the bulk of repair costs.  i can't clean my best shoes as well as the chappy charging five quid outside the Bank of England, but I can do a reasonable job in the 10 minutes from spit to polish as he can in five.

So  for those who can live with effectiveness rather than perfection many of these jobs just require time, a bit of patience and practise helps make less imperfect.

Leather - excellent leather (not all pre-cut etc etc which David Leese supplies so nicely) to do this kind of job, can be had for a two or three quid a suare YARD rough offcut.
If u want the address I can dig it out. It is large offcuts from producing ladies thin leather glove/leather art items.
I also collect old leather handbags which are sometimes very thin leather and you will often find lady's leather trousers of thin leather/suede for a couple of quid at boot sale (or for nowt in my case as my sister was about to throw them out....) At almost zero cost you can practise and throw away to your hearts content all day....  and I often take advantages of the greater skill which women's smaller hands have when doing this kind of sometimes picky work e.g. squeezing down a gluey patch on a gusset corner inside a narrow bellows.....
 
 And if you want tapered edges after you have measured and cut your strips then you can use razor, old cuthroat etc etc. **

 As a student I had a 3.8litre MkIX Jaguar in two=tone racing green (same model as u saw Marilyn Monroe riding around in) .. I might consider a two tone bellows if I run out of black leather offcuts and have to use some brown or vv...
Embossing: At 14 or so, a couple of us used to repair all the school library books,spines, boards, rexine and leather covers, and we even did gold plated lettering and embossing...no one taught us,we scavanged the basic gear (old steel presses and metal letters which we stuck in the fire or did cold with gold/silver leaf, and they were quite presentable so.....if we could do... we also acquired our own workroom where we drank....    tea etc...

** http://www.concertina.net/forums/index.php?showtopic=11031&view=&hl=strop&fromsearch=1

I believe there are also several accordion part suppliers whose material may suit 'bigger' dimensions of melodeons compared with small tina bellows etc.

Must go -
Off to a session on Hadrian's Wall so haave to put my leather gladiator sandals on before saddling my horse with leather saddle and my horsebox-holding-strap...
http://www.roman-colosseum.info/roman-clothing/gladiator-sandals.htm
Logged

Tony M

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: plastic paint to strengthen paper bellows joints and gussets
« Reply #11 on: April 29, 2010, 01:01:18 PM »


Leather - excellent leather (not all pre-cut etc etc which David Leese supplies so nicely) to do this kind of job, can be had for a two or three quid a suare YARD rough offcut.
If u want the address I can dig it out.

No firm decision on which way to go forward yet (I'm not in a rush), but a source of offcuts like that would be useful knowledge, if it's not too much trouble to dig out.

I'm also investigating the linen tape - as Al noted, it's a bit pricey, at least from the places I've looked at so far.  Almost the price of good leather strip - but capable of different uses, thin and easy to apply without having to dismantle the bellows.  It's really handy to know about such things.

Cheers,

Tony
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: plastic paint to strengthen paper bellows joints and gussets
« Reply #12 on: April 29, 2010, 02:15:51 PM »

be careful which leather you choose, some soft clothing leathers are not at all airtight, pigskin in particular.  Sheep nappa should be ok and is readily available in various colours and thickneses.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

HallelujahAl

  • Guest
Re: plastic paint to strengthen paper bellows joints and gussets
« Reply #13 on: April 29, 2010, 03:54:26 PM »

Quote
I'm also investigating the linen tape - as Al noted, it's a bit pricey, at least from the places I've looked at so far.


It is pricey over here in the UK 0- but as I said I import mine from the States where its a fraction of the price. I have quite a bit so let me know how much you need and I may be able to help you.
AL
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: plastic paint to strengthen paper bellows joints and gussets
« Reply #14 on: April 29, 2010, 05:57:04 PM »

I don't know what is regarded as pricey, but I've used this firm, www.ukindustrialtapes.co.uk which works out at about £1 a metre
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Tony M

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: plastic paint to strengthen paper bellows joints and gussets
« Reply #15 on: April 29, 2010, 08:12:37 PM »

Much appreciate the advice from all of you - especially Theo's comment about different leathers and the link to the tape supplier.

"Pricey" is indeed rather subjective - the supplier Theo suggested above has not only a big range at what seem like competitive unit prices, but also a reasonable P&P cost.  (Some others aren't interested in small orders, or want combined P&P / handling costs that are comparable with the value of a small order.)  I've also discovered, in looking at some of these suppliers, that there's a whole range of products out there that I was completely unaware of (= lots of possibilities, but lots of uncertain outcomes!)

Problem is, spend a few pounds on this and a few on that (experimenting with ideas and materials), and it's easy to "prototype" towards the cost of doing a good job without actually getting round to improving the instrument.  I'm starting to lean towards the idea of doing the job with proper leather strip - on the basis that it'll only need doing once, and the result is fairly certain.

I'll ponder a while longer, I think.

Thanks again, all.

Tony.
Logged

Kautilya

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 977
Re: plastic paint to strengthen paper bellows joints and gussets
« Reply #16 on: April 29, 2010, 11:53:49 PM »


Leather - excellent leather (not all pre-cut etc etc which David Leese supplies so nicely) to do this kind of job, can be had for a two or three quid a suare YARD rough offcut.
If u want the address I can dig it out.

No firm decision on which way to go forward yet (I'm not in a rush), but a source of offcuts like that would be useful knowledge, if it's not too much trouble to dig out.

will dig - remind me Monday if not done.
Logged

Kautilya

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 977
Re: plastic paint to strengthen paper bellows joints and gussets
« Reply #17 on: April 29, 2010, 11:54:38 PM »

be careful which leather you choose, some soft clothing leathers are not at all airtight, pigskin in particular.  Sheep nappa should be ok and is readily available in various colours and thickneses.

 would glue [erhaps not seal doubtful (naturally leaky) leath when strips are applied?
Logged

Kautilya

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 977
Re: plastic paint to strengthen paper bellows joints and gussets
« Reply #18 on: May 01, 2010, 09:54:27 PM »


Leather - excellent leather (not all pre-cut etc etc which David Leese supplies so nicely) to do this kind of job, can be had for a two or three quid a suare YARD rough offcut.
If u want the address I can dig it out.

No firm decision on which way to go forward yet (I'm not in a rush), but a source of offcuts like that would be useful knowledge, if it's not too much trouble to dig out.

will dig - remind me Monday if not done.

The Identity shop in Matlock.

I see it is Dec 2008 when I ordered various glues and dyes, applicators, leather restorer, blades, celtic symbols etc etc.

Jackie is the person. She wont remember me but if you say  it was someone  looking for glove leather offcuts to use on melodeon / concertina bellows and you want to ask her about the same, she will understand.  At that date it was pounds 1.50 upwards [[per offcut,  depending on size per piece of lightweight gloving leather. I see they normally sell the pukka leather by weight which is always a good sign.

I am sure she will be happy (as she did with us) to send you a sample, but you can always dye to match existing. A mate of mine who is one of the world's greatest antique carpet restorers sometimes uses coloured felt tip pens to match ancient silk with new....  honi soit  qui mal y pense... - honey, if you can't afford silk stockings use a permanent marker to run a line down the back of your leg.......

Clearly you need offcuts that will allow you to cut multiple strips of a certain length to go on each binding and all  round (or as u need) so mention that.  If u did go  for a full rebind then u would be best to calculate how much of the same colour leather that would be. But very good at advising so ring up. All contacts on the website.

www.theidentityshop.co.uk
« Last Edit: May 01, 2010, 10:07:12 PM by Kautilya »
Logged

Tony M

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: plastic paint to strengthen paper bellows joints and gussets
« Reply #19 on: May 02, 2010, 03:03:31 PM »

Many thanks for that.

The link seems to have changed - that one took me to a search page.

I guess their web address has changed slightly - a quick Google led to http://www.theidentitystore.co.uk/.  Definitely the right place, and lots of useful stuff there.

Thanks again,

Tony.
Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal