Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Re-taping Bellows  (Read 8127 times)

0 Members and 1 Guest are viewing this topic.

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re-taping Bellows
« on: March 27, 2008, 06:58:11 PM »

I have a 1930's or so three voice, two row Hohner with 20 fold bellows that need retaping. The back and the bottom are the bad bits but I don't like doing half a job so I thought I'd do the lot which involves some 24.6 meters of tape. What I don't know is what's involved in carrying out the work and what the potential pitfalls (if any) are.

Is striping off the old tape tricky or likely to cause damage to the bellows cards? What kind of adhesive is used to glue on the new tape and how quickly does it dry?

Any hints or tips about doing the job and sources of materials greatly appreciated.

Pete.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: Re-taping Bellows
« Reply #1 on: March 27, 2008, 07:58:07 PM »

I replaced the bottom-side tape on my Corona following instructions found on Bernard Loffet's help pages  (they are in French! but there are a few pics).

It's not difficult, but it takes time and patience and it's precision work. Removing the old tape can be tricky, you don't want to damage the bellows by doing so, it also depends on what type of glue they used when installing the original tape.

Each tape strip must be cut to the same exact length and carefully installed so all ends are aligned on a straight line and the tape strips are centered. If using tape with a moiré effect all strips must be installed following the same direction. When applying a strip of tape, you need to make sure it is properly affixed and centered, then close the bellows to keep it in place while you get the next strip ready. The first one is easy to install, but it gets tricky from the second one on! Take your time. It's easier if you fold the tape before glueing. If there is any excess glue wipe it off with a paper towel or clean rag.

I used simple white glue, as suggested by Bernard. He mentions that you need about 17 metres of tape for a typical Pokerwork-size bellows.

« Last Edit: March 27, 2008, 07:59:47 PM by québécois »
Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18

suesqueezer

  • Member
  • *
  • Offline Offline
  • Posts: 16
  • Piana accordion player now attempting all buttons!
Re: Re-taping Bellows
« Reply #2 on: March 27, 2008, 08:39:01 PM »


As mentioned, cut exactly the same size lengths for the sides as needed first. Make sure you have a clean edge by removing old tape first - if ya lay it on top it's adding to the thickness overall and where is was loose and worn will just create a bad adhesion. The trick to working with each piece of tape is all in the glue. Get yourself of piece of glass or a plastic rigid sheet, and apply the glue to this by using a piece of cardboard and trowelling it into an even patch of glue maybe 1/32 inch thick and as wide as 3 pieces of tape width, then I lay my pieces of tape onto the surface, so you are covering the bottom of tape pieces fairly evenly - just touch em down with your finger a bit. Then I lift em off and set aside - you will see that only a textured amount went on the backs this way. In case there's misses on the backs just touch up with more glue.  THE KEY NOW IS "TACKING UP" OF GLUE. It's good to let the glue sort of dry up a bit. Then get some clothespins or cotton balls and put them in each of bellows so the one you are taping is sort of on its own. Then lay down a glue covered piece as best as you can centred on width and length and squish down & adjust - it will still be a bit moveable and this way very little excess glue. Have a wet damp rag on hand to smooth over the applied tape and any excess glue removed. After you do a side, cut some pieces of wax paper and stick inbetween each bellow and put some weight on the whole bellows to really set. I use WeldBond glue which is a white glue and drys clear.
Logged

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Re-taping Bellows
« Reply #3 on: March 27, 2008, 10:21:12 PM »

Thanks for the helpful comments, I'm fairly used to working with the leather top runs on concertina bellows and found out by trial and error that rebinding over existing leather gives far too much bulk to the finished bellows and soaking too much to get the old stuff off leaves you with a pile of useless parts!

In normal circumstances I would have gone for PVA (white glue, Elmer's, call it what you will) but I wasn't sure that would work where the tape overlaps the metal corners. I wasn't sure either if there was any stretch in the tape bindings but the advice to cut precisely to length beforehand suggests not. So do I just carefully remove the old tape dry or will damping down first help (or indeed cause a disaster)?
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Re-taping Bellows
« Reply #4 on: March 27, 2008, 11:18:13 PM »

Just remove the old tape dry.  Carefully lift one end and it should pull off in one piece.  You might want to scrape off loose material left behind.  The tape is not significantly stretchable.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Bill Young

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1151
  • Paolo Soprani BCC#
Re: Re-taping Bellows
« Reply #5 on: March 05, 2009, 04:33:22 PM »

I'm sure I've read a pretty detailed posting by Theo, some time ago, on how to do bellows retaping (like, how many folds to do at a time), but I can't find it. I'd like to read it again to see whether it's something I want to attempt. Could someone please provide a pointer to the item? Or maybe it was on the old forum?

Grateful for any help.
Logged

rileycat

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 429
Re: Re-taping Bellows
« Reply #6 on: March 05, 2009, 05:01:15 PM »

Hi Pete
If it is any help and not too late, Charlie Marshall - CGM Musicals - does a good pot of specific bellows tape glue, which can be easily spread by finger and which "grips" and dries quite easily as long as you don't try to do too many folds at a time. I'd keep off the PVA, white-glue stuff as it lacks the "grip" and seems messy in use when compared with the "proper" stuff. However, whatever you use, as others have said, take your time, cut very carefully and keep the folds clean.
Tony
Logged

nomad

  • Good talker
  • **
  • Offline Offline
  • Posts: 70
Re: Re-taping Bellows
« Reply #7 on: May 08, 2011, 09:52:58 PM »

Hi

I am going to have a go at my first ever bellow repair. I need to replace some metal corners which will involve adding tape to the bellows.

So i have a few questions.

1) Do you renew the bellow tape down the full length of the bellows or do you just take it back a couple of inches and replace a small section.

2) If only replacing a sectin do you slightly overlap the original remaining tape

3)My bellow tape is 3/4" if i was to renew the full length would i be better using 1" bellow tape to cover any old glue lines.

4)Are metal bellow corners easy to fit.

Any tips on any of the above will be most welcomed,

Thanks
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Re-taping Bellows
« Reply #8 on: May 08, 2011, 10:35:04 PM »

1) Do you renew the bellow tape down the full length of the bellows or do you just take it back a couple of inches and replace a small section.

I would replace the whole length, which would probably drive me to replace all the tape on the bellows so it matched  ;)

Quote
2) If only replacing a sectin do you slightly overlap the original remaining tape

See above or butt the repair to the old tape.

Quote
3)My bellow tape is 3/4" if i was to renew the full length would i be better using 1" bellow tape to cover any old glue lines.

I would use 3/4"

Quote
4)Are metal bellow corners easy to fit.


Not that difficult, I use contact adhesive and big pliers, more info here Search is your friend  ;D

nomad

  • Good talker
  • **
  • Offline Offline
  • Posts: 70
Re: Re-taping Bellows
« Reply #9 on: May 08, 2011, 11:52:20 PM »

Thanks for the reply Lester, deep down I sort of knew the correct thing to do was the renew the full length, and I will do all the bellows.

Thanks
Logged

dahlberg

  • Custom
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 172
  • Huvvaligen
    • Spelparkering
Re: Re-taping Bellows
« Reply #10 on: August 09, 2011, 07:24:36 AM »

*bump*
Half way thru re-taping the Granesso i discovered there is a huge leak closest to the frame.
How to solve this?
What about glue a strip of paper from inside?

(edit:added pic)
« Last Edit: August 09, 2011, 07:44:24 AM by dahlberg »
Logged

Keithypete.

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 917
Re: Re-taping Bellows
« Reply #11 on: August 20, 2012, 09:58:49 AM »

Do I need to remove 100 % of the old, gold Pokerwork paper? Most of it has come away cleanly, but some is hanging on, the top layer having peeled off leaving the half with the glue.
Does the extra thickness of the tape cause any problems?
Logged
Beltuna Sara II - B/C flavour.
Borsini - G,D,A.
Pokerwork B/C.
PRIMATONA IV, B/C.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Re-taping Bellows
« Reply #12 on: August 20, 2012, 10:15:40 AM »

I would, a gentle dampening will normally free it up
« Last Edit: August 20, 2012, 01:10:26 PM by Lester »
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Re-taping Bellows
« Reply #13 on: August 20, 2012, 12:59:29 PM »

I know this perhaps addressing advanced techniques (and I haven't even attempted the basics)...  I had the back and bottom of the bellows on a Club IIB Victoria retaped by a professional (Hohner trained), actually I'd only asked him to retune.  He has used ribbed black Italian tape and unlike on a new set of bellows, the alignment of the ribbing makes a random pattern rather than the immaculate diagonal one has come to expect.  If I eventually get round to taping the other two, more visible sides do I just have to accept that the ends may not be perfectly aligned so as to get the pattern established - or does one faff about working out how to cut the pieces against a guage to achieve a perfect result?

I guess its a choice between a long, boring but simplish job or a longer, more frustrating job to get the alignment.  Might even consider an insert pattern in gold if going to all the trouble!

Perhaps I should just send the measurement to the niece's in-laws in Port Recanati...

Rob.
Logged

Keithypete.

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 917
Re: Re-taping Bellows
« Reply #14 on: August 20, 2012, 01:04:16 PM »

OK. Judicial use of a cotton bud did the trick.

Now to go in gently to remove the the bits tucked in next to the bellows frames. Some of the Orange has come away in a few places too. I think I will be able to touch it up with paint of one sort or another. I may paint the whole lot a different colour. Has anyone tried this? What are the options?
Logged
Beltuna Sara II - B/C flavour.
Borsini - G,D,A.
Pokerwork B/C.
PRIMATONA IV, B/C.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Re-taping Bellows
« Reply #15 on: August 20, 2012, 01:07:00 PM »

I know this perhaps addressing advanced techniques (and I haven't even attempted the basics)...  I had the back and bottom of the bellows on a Club IIB Victoria retaped by a professional (Hohner trained), actually I'd only asked him to retune.  He has used ribbed black Italian tape and unlike on a new set of bellows, the alignment of the ribbing makes a random pattern rather than the immaculate diagonal one has come to expect.  If I eventually get round to taping the other two, more visible sides do I just have to accept that the ends may not be perfectly aligned so as to get the pattern established - or does one faff about working out how to cut the pieces against a guage to achieve a perfect result?

I guess its a choice between a long, boring but simplish job or a longer, more frustrating job to get the alignment.  Might even consider an insert pattern in gold if going to all the trouble!

Perhaps I should just send the measurement to the niece's in-laws in Port Recanati...

Rob.

I don't attempt to align the pattern  and I don't know I have ever seen is done but it is important to make sure all the tape runs in the same direction otherwise it looks really poor. As I cut the tape I mark the free end and I mark the bellows so it is easy to ensure the orientation.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Re-taping Bellows
« Reply #16 on: August 20, 2012, 01:09:52 PM »

OK. Judicial use of a cotton bud did the trick.

Now to go in gently to remove the the bits tucked in next to the bellows frames. Some of the Orange has come away in a few places too. I think I will be able to touch it up with paint of one sort or another. I may paint the whole lot a different colour. Has anyone tried this? What are the options?

I have a tester can of Dulux emulsion to do odd touch ups. Take your bellows to B&Q and they can scan the colour to generate a match pot. I have also repainted whole bellows using the same paint, takes a deal of preparation though.

Keithypete.

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 917
Re: Re-taping Bellows
« Reply #17 on: September 02, 2012, 11:14:30 AM »

I got some bellows tape from CGM, along with the appropriate glue. Also in the parcel was a sheet of paper with tips on how to do the job properly. As with most things it's all in the preparation.

The glue is queer old stuff & to be honest I had no faith in it, having never used it before, but it is actually very good. The gluing & putting on of the tape can be quite quickly done, once the prep and set up is out of the way.

About half done now.
Photos to follow when I have done the other half.
Logged
Beltuna Sara II - B/C flavour.
Borsini - G,D,A.
Pokerwork B/C.
PRIMATONA IV, B/C.

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Re-taping Bellows
« Reply #18 on: September 02, 2012, 12:06:09 PM »


I have a tester can of Dulux emulsion to do odd touch ups. Take your bellows to B&Q and they can scan the colour to generate a match pot. I have also repainted whole bellows using the same paint, takes a deal of preparation though.
Just curious - how durable has this proven to be? And what preparation do is needed, apart from the obvious cleaning and de-fluffing?
Malcolm
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Re-taping Bellows
« Reply #19 on: September 02, 2012, 02:03:17 PM »

Seems to last OK. Did nothing other than clean out the fluff prior to slapping it on.
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal