Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 3 [4] 5 6 7   Go Down

Author Topic: A series of holiday projects  (Read 38023 times)

0 Members and 1 Guest are viewing this topic.

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: A series of holiday projects
« Reply #60 on: November 15, 2010, 03:14:16 AM »

OK, bostik. How do you make it usable? It is so sticky, it just separates into massive strands and is impossible to apply. The only way that I could do it is to apply the glue directly to the underside of the valve, but it is so easy to apply and when it contracts then it buckles the valve and I have to discard it. Tips? A friend suggested putting it on the radiator for a few minutes to heat it up.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: A series of holiday projects
« Reply #61 on: November 15, 2010, 08:01:26 AM »

OK, bostik. How do you make it usable? It is so sticky, it just separates into massive strands and is impossible to apply. The only way that I could do it is to apply the glue directly to the underside of the valve, but it is so easy to apply and when it contracts then it buckles the valve and I have to discard it. Tips? A friend suggested putting it on the radiator for a few minutes to heat it up.

I just lay the tube down on my glueing board (IKEA plastic chopping board) and by gently applying pressure a small amount of glue can be dispensed directly on to the valve which, if pressed firmly in place, should not crinkle.

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: A series of holiday projects
« Reply #62 on: November 15, 2010, 08:47:45 PM »

Or a blob on a matchstick / toothpick / wire / point ended object of own choice so you have the equivalent to the 'unsend' key which you may get if picking it up on the valve from the tube nozzle (teashirt etc. etc.)

Reading through History unfolds they use a backlight and reedplate sized hole in a blanking sheet so you can see if the reed it centralised in the plate by the line of light around it - may also show up any burrs / corrosion / other cr@p which might distort its dulcet tones......

Richard
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: A series of holiday projects
« Reply #63 on: November 15, 2010, 10:19:28 PM »

Quote
I just lay the tube down on my glueing board (IKEA plastic chopping board)...

Brilliant, hadn't thought of going there for assorted workbench items. Compared with the Home Creepo, $0.69 for a work surface is a steal. I bet there are all sorts of things in there waiting to be re-purposed.

Imagine : "Yes dear, I'd love to go to IKEA! Love to!" She used to have to bribe me with creamed herring.

Sorry for the diversion. It is an interesting thread, please proceed...  ;D

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: A series of holiday projects
« Reply #64 on: November 16, 2010, 01:17:09 AM »

Progress:

Work is slow, as I can only really spend an hour a day or so. The one row has had all of it's reeds stripped, cleaned, reset and revalved on one side. I'm not sure how critical revalving the uppermost side is before tuning, I suppose that it would make some difference. Bellows gasket has been replaced (and annoyingly leaks on one corner, due to the join overlapping, which of course I didn't notice). I've tried filling said join with glue, if that doesn't work I'll put new gasket on again. I need to attach the strap brackets and thumbstrap (I'm thinking a locknut or similar), rewax (hopefully done tomorrow, depending on how things go), new grille cloth and of course tuning.

The Weltmeister needs new gaskets, reed overhaul (although the reeds are in better condition than the hohner, the bass action needs swedging, retuning, new bellows straps. Also needs a new grille and ideally a new fingerboard, which will be fun. The grille I've started on, the fingerboard will provide much needed practice with CAD/CAM. Might start the reed overhaul this week, I'm quite enjoying it. Very relaxing.

The PA I'm leaving for a bit, mainly because I've realised just how difficult waxing in the tiny reeds is going to be, so I'm leaving that till last. That needs retaping, new bellows straps, full reed overhaul, new gaskets and so on.

Tuning is still the storm cloud on my horizon. I'm sort of prepared except that I still don't have a scraper.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: A series of holiday projects
« Reply #65 on: November 16, 2010, 07:31:59 AM »

<snip>
Bellows gasket has been replaced (and annoyingly leaks on one corner, due to the join overlapping, which of course I didn't notice). I've tried filling said join with glue, if that doesn't work I'll put new gasket on again.
</snip>
For what it's worth, my methodology is that if there is a sufficiently good seal on the old bellows gasket to enable you to carry out the other restoration/reed work first, leave the gasket replacement as the last job to be done. The reason I do this is that whilst carrying out the other work, the repeated removal and re-assembly of the bellows from the instrument's ends may cause further detriment to the gasket and hence the air-tightness. Once you are happy with the reeds and the tuning, only then replace the bellows gasket, and then disturb it as little as possible thereafter.

If you have an air leak caused by a section of overlapping gasket, you should be able to use a very sharp blade to make a single cut vertically down through the overlapping strata (guess my profession!), remove the overthrust section and press the remaining part of the ramp down into place, butting it up to the other end of the gasket. It ought to butt up snugly and will become even more snug when the gasket is compressed on reassembly.

It is also not a good idea to have your join on a corner; make it on one of the straight sections instead.
« Last Edit: November 16, 2010, 07:35:33 AM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: A series of holiday projects
« Reply #66 on: November 16, 2010, 08:10:38 AM »

Re: fitting 'outside' valve.   There is no point IMHO in not fitting the outside valve.  If you use a good  slim scratched you only need to lift the valve a tiny amount to get the scratched, or the reed lifter into position.  Fitting the valve does make a small but significant flattening of the pitch of the reed.  If you plan to have wet tuning it probably won't be noticable,  but with dry or swing tuning you will not get a good result.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: A series of holiday projects
« Reply #67 on: November 16, 2010, 01:12:19 PM »

Re: fitting 'outside' valve.   There is no point IMHO in not fitting the outside valve.  If you use a good  slim scratched you only need to lift the valve a tiny amount to get the scratched, or the reed lifter into position.  Fitting the valve does make a small but significant flattening of the pitch of the reed.  If you plan to have wet tuning it probably won't be noticable,  but with dry or swing tuning you will not get a good result.

Cool, I'll do that then.

<snip>
Bellows gasket has been replaced (and annoyingly leaks on one corner, due to the join overlapping, which of course I didn't notice). I've tried filling said join with glue, if that doesn't work I'll put new gasket on again.
</snip>
For what it's worth, my methodology is that if there is a sufficiently good seal on the old bellows gasket to enable you to carry out the other restoration/reed work first, leave the gasket replacement as the last job to be done. The reason I do this is that whilst carrying out the other work, the repeated removal and re-assembly of the bellows from the instrument's ends may cause further detriment to the gasket and hence the air-tightness. Once you are happy with the reeds and the tuning, only then replace the bellows gasket, and then disturb it as little as possible thereafter.

If you have an air leak caused by a section of overlapping gasket, you should be able to use a very sharp blade to make a single cut vertically down through the overlapping strata (guess my profession!), remove the overthrust section and press the remaining part of the ramp down into place, butting it up to the other end of the gasket. It ought to butt up snugly and will become even more snug when the gasket is compressed on reassembly.

It is also not a good idea to have your join on a corner; make it on one of the straight sections instead.

Good advice. You misunderstand me though, the join is on the box, not the gasket! It's got mitred corners, but there is a bit of a gap where some wood has been chipped away or something. In future though I will fit the gasket last.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: A series of holiday projects
« Reply #68 on: November 16, 2010, 03:21:21 PM »

Good advice. You misunderstand me though, the join is on the box, not the gasket! It's got mitred corners, but there is a bit of a gap where some wood has been chipped away or something.
Ah - that's more like it. I thought it sounded a bit odd!
Yes - you can use PVA woodworking glue to fill small gaps. It's even better if you can get some fine wood dust approximately the same colour as the original wood. Rub some scrap wood on a file or carborundum paper and collect the wood dust. Mix it with a blob of glue and then gradually feed it in to the gap. You might need to use several applications to fill a deep hole. When thoroughly dry, file/sand smooth.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: A series of holiday projects
« Reply #69 on: November 16, 2010, 03:39:02 PM »

One problem with pva is that you really need to get the joint completely apart to get the glue to all parts.  If you just press pva into trhe visible cracks you may stop the air leaks but quite probably the joint will still be weak and may spring open again. In this sort of case you would cause much greater damage by taking the casing apart to get the glue where it needs to be.   

In this situation I much prefer to use superglue/cyanoacrylate because it is able to penetrate into the finest cracks by capillary action.    Use a good quality well know brand, and don't use the thicker gel types, nor the extra thin type.   Use clamps to get the crack to close up before applying any glue, the feed the superglue along all visible parts of the crack inside the box as well as outside,   after a few moments you should see the liquid disappear along the line of the crack,  when this happens add a little more glue and continue adding it until no more is absorbed.   Then leave the clamps in place for 25 hours - superglue sometimes needs longer to fully cure in deep cracks.

The result should be an airtight joint with good resistance to future cracking.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: A series of holiday projects
« Reply #70 on: November 16, 2010, 07:45:30 PM »

One problem with pva is that you really need to get the joint completely apart to get the glue to all parts.  If you just press pva into trhe visible cracks you may stop the air leaks but quite probably the joint will still be weak and may spring open again. In this sort of case you would cause much greater damage by taking the casing apart to get the glue where it needs to be.    

In this situation I much prefer to use superglue/cyanoacrylate because it is able to penetrate into the finest cracks by capillary action.    Use a good quality well know brand, and don't use the thicker gel types, nor the extra thin type.   Use clamps to get the crack to close up before applying any glue, the feed the superglue along all visible parts of the crack inside the box as well as outside,   after a few moments you should see the liquid disappear along the line of the crack,  when this happens add a little more glue and continue adding it until no more is absorbed.   Then leave the clamps in place for 25 hours - superglue sometimes needs longer to fully cure in deep cracks.

The result should be an airtight joint with good resistance to future cracking.

Ah - that's more like it. I thought it sounded a bit odd!
Yes - you can use PVA woodworking glue to fill small gaps. It's even better if you can get some fine wood dust approximately the same colour as the original wood. Rub some scrap wood on a file or carborundum paper and collect the wood dust. Mix it with a blob of glue and then gradually feed it in to the gap. You might need to use several applications to fill a deep hole. When thoroughly dry, file/sand smooth.

Thanks for that Theo and Steve. The joint hasn't split apart, it's just a bit damaged. I don't have any scrap wood (unless I use some of College's furniture :P) and don't have any superglue, but if I do have to reglue a joint then I will bear that in mind. In this case, I've dabbed a bit of wax over it and it's sealing a lot better now. I may still redo the gasket after finishing the rest of it though.

Progress for today: Finished revalving and rewaxed treble and bass ends. Had a few plates that were initially waxed in the wrong places on the bass end, but that is fixed now. Note to self: it is all very well keeping the order of the plates constant in whatever you do, but just in case you have got them mixed up, it's a good idea to check before waxing!

The treble side I have tested and all notes sound, in the right order in the right direction, with no warbles, rattles etc. which is encouraging. The bass end is drying as we speak. Or as I type, anyway. I've been using an encaustic stylus to wax, which takes a bit of getting used to, but is very easy to do once you've got the hang of it. Plug it in, wait to warm up, stick into wax block and draw along like a pen. The tricky bit is getting the speed right, too slow and the wax is too thick, too thin and it won't make a good seal. It helps to angle it so that you can see the wax flowing out of the head. Some of my plates aren't waxed in particularly neatly, but this was my first time and I'm fairly pleased with it.

I've also installed some strap brackets, replaced the treble grille cloth and have replaced half of the bass end cloth. After that I need to test the pallets for leaks, replace as necessary and then it's just tuning...

Might do a reed overhaul on the Weltmeister first :P I'm enjoying reed work and I love the smell of reed wax (although I hear that it isn't very good for you).
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: A series of holiday projects
« Reply #71 on: November 16, 2010, 11:58:24 PM »

:P I'm enjoying reed work and I love the smell of reed wax (although I hear that it isn't very good for you).

Wax fumes gave me asthma.  It is no joke.  You must avoid inhaling the fumes from the melted wax.  The nice smell from the warm wax as it cools is probably safe, but if you encaustic stylus produces any fumes then for the sake of your health you should work with a fume extractor.  Anyone in the university who does soldering should have one.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: A series of holiday projects
« Reply #72 on: November 17, 2010, 02:01:26 AM »

:P I'm enjoying reed work and I love the smell of reed wax (although I hear that it isn't very good for you).

Wax fumes gave me asthma.  It is no joke.  You must avoid inhaling the fumes from the melted wax.  The nice smell from the warm wax as it cools is probably safe, but if you encaustic stylus produces any fumes then for the sake of your health you should work with a fume extractor.  Anyone in the university who does soldering should have one.

I haven't seen any smoke, no wax is burning. The stylus is warm enough that you notice if it touches you but nowhere near warm enough to burn you. I don't know how to know whether it is a problem, does wax just give off harmful fumes when it melts? If so that is really quite inconvenient :P

I think I trapped one of the bass chord valves under the plate, it's rattling. Bother, nearly perfect. Also a few reeds seem to have shot sharp, markedly. I'm wondering whether I've done something to them or whether it's just a byproduct of an overhaul.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: A series of holiday projects
« Reply #73 on: November 17, 2010, 03:06:03 AM »

Quote
...you should be able to use a very sharp blade to make a single cut vertically down through the overlapping strata (guess my profession!)...

Dunno, prolly a gneiss one you shouldn't take for granite.. chalk full of interesting specimens, no doubt..

'coat!  :|glug

(The missus and I are rockhounds, too, albeit of the amateur variety.)

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: A series of holiday projects
« Reply #74 on: November 17, 2010, 06:49:38 AM »

I think I trapped one of the bass chord valves under the plate, it's rattling. Bother, nearly perfect.
Bother indeed :( !
The valve may be fouling the side or end of the chamber and not lifting correctly, allowing the reed tongue to vibrate against the valve. At least you've identified the most likely cause and can proceed to investigate and put it right.

Quote
Also a few reeds seem to have shot sharp, markedly. I'm wondering whether I've done something to them or whether it's just a byproduct of an overhaul.
The change in pitch is probably a result of the rewaxing and revalving. The final frequency of the reed tongue is partly controlled by the acoustic coupling between the tongue and all the other nearby components which 'force' their own frequencies on to the tongue vibration. Rewaxing will change ('improve') that acoustic coupling and renewing the valves will also have an effect too. This is why it is very desirable to do the final tuning with the reed blocks in-situ, using the instrument's own bellows or else a tuning bellows of the same dimensions as the instrument's. 
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: A series of holiday projects
« Reply #75 on: November 17, 2010, 11:48:45 AM »

I think I trapped one of the bass chord valves under the plate, it's rattling. Bother, nearly perfect.
Bother indeed :( !
The valve may be fouling the side or end of the chamber and not lifting correctly, allowing the reed tongue to vibrate against the valve. At least you've identified the most likely cause and can proceed to investigate and put it right.

Well I got the offending reed plate wrong, so I unwaxed two before I found the right one. I've rewaxed it, it still rattled. I removed both valves and rewaxed it again, it still rattled, I've just this moment realised what it must be and have tested. The reed was fouling the plate ever so slightly. Not enough to prevent it sounding, but enough to get it to rattle.  Most annoying. Still, it isn't any more, I've reset it.

Another thing that I've found is that there is a substantial delay before one of my reeds sounds. Is this to do with tip clearance or reed angle away from the plate or something?

Quote
The change in pitch is probably a result of the rewaxing and revalving. The final frequency of the reed tongue is partly controlled by the acoustic coupling between the tongue and all the other nearby components which 'force' their own frequencies on to the tongue vibration. Rewaxing will change ('improve') that acoustic coupling and renewing the valves will also have an effect too. This is why it is very desirable to do the final tuning with the reed blocks in-situ, using the instrument's own bellows or else a tuning bellows of the same dimensions as the instrument's. 

Cool, that's what I thought. As long as it isn't me, all is well!

This instrument is flat mounted, which makes some things more difficult. Not sure whether it's best to start tuning this or to start with the Weltmeister. This one is worth more to me (and worth more in real terms) and also has H reeds instead of T reeds (which are no longer available), so it might be more sensible to start with the welty.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: A series of holiday projects
« Reply #76 on: November 18, 2010, 12:30:27 PM »

OK, three questions:

Firstly, different response times, it this due to the angle that the reed makes with the plate, in the direction normal to the plate?

Secondly, one of my reds plays fine at very low pressures but sharpens at higher pressures. I don't know what this means but I'm guessing that it's bad :( To my knowledge I haven't done anything to it, haven't started tuning yet.

Thirdly is there an easy way of stripping old pallet leather off pallets? It's a horrible job and I'm worried that I'm not making the surface as flat as it should be.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: A series of holiday projects
« Reply #77 on: November 18, 2010, 02:40:48 PM »

Delays in reed response with audible air is either a leak, or the opposite reed valve is either hung open or in bad shape, but usually the reed tip gap is too big.  As you be finding out by now, it takes very little to make a big difference in these contraptions.  You should be able to compare the reed gap with the surrounding ones to get an idea if it's too big, if it's a visible reed. 

I also found, like you, that making changes inside can often affect tune. 

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: A series of holiday projects
« Reply #78 on: November 18, 2010, 02:54:50 PM »

Reeds that sharpen can be caused by something fouling the reed tongue in the lower third of the reed tongue.  Sometimes glue from the adjacent valve can squeeze out enough to reach the reed.

I peel off pallet leathers with the aid of a sharp knife, then sand down to clean wood with a sheet of coarse abrasive paper glued into a board.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: A series of holiday projects
« Reply #79 on: November 18, 2010, 03:02:33 PM »

OK, three questions:

Firstly, different response times, it this due to the angle that the reed makes with the plate, in the direction normal to the plate?

Secondly, one of my reds plays fine at very low pressures but sharpens at higher pressures. I don't know what this means but I'm guessing that it's bad :( To my knowledge I haven't done anything to it, haven't started tuning yet.

Thirdly is there an easy way of stripping old pallet leather off pallets? It's a horrible job and I'm worried that I'm not making the surface as flat as it should be.
Ans.1
Yes, the set of the reed - the gap - governs the response. If the gap is too wide, the reed will be slow to start and may sound loud but breathy when it does get going. If the gap is too narrow, the reed will speak easily at low bellows pressure, but will tend to choke off at higher pressures. A gap which is exceptionally narrow may fail to speak at all. Compare with the gap of neighbouring reeds that do have the correct response.

Ans.2
This also sounds as if the gap is not adjusted correctly. I think I am right in saying that a gap which is slightly too narrow will exhibit the pitch changes you mention - i.e. sharpens at higher pressures. But this isn't necessarily a constant rule.

The gap can be adjusted very carefully. To increase the gap, slide a thin shim under the reed tongue to about 1/3 or 1/2 its length and very gently lever up the reed tongue until you begin to feel a little bit of increased resistance. Do this a little bit at a time, checking the result by sounding the reed either in the instrument or on the block on a tuning bellows. You may not be able to notice any difference visually - small fractions of a milimetre can make all the difference.

To reduce the gap, use a non-scratching pointy thing like a cocktail stick to gently depress the reed into the slot a few times. Again go very carefully, a bit at a time and test the result constantly.

For reeds on the underside of the reed plate the procedure is the same, except it is more awkward to make the gap narrower. You will need to use a reed lifter - either the Italian hook style, or the Hohner lever style - to pull the reed into the reed plate slot and then lift it even further with a shim.

For each reed there will be a 'sweet spot' setting where the adjustment is just right. The amount of gap can also be tailored to your own playing style. If you are a habitual forceful bellows player, you will need a slightly increased gap setting. Remember that the gap setting can affect the tuning, and also that filing/scratching a reed to tune it can change the stresses in the reed tongue which may cause it to bend very slightly with resulting effects on the gap. So - it's a wonder that reeds can ever be tuned and respond properly. But of course they can even though it is a trade-off compromise between speed of response and constancy of pitch at differing bellows pressures. It goes to show that tuning and setting a reed is an art and fine skill, where experience, patience and a good ear are the best teachers. Don't be too afraid of trying it - it's the only way to learn, but go very carefully.

Except in a single voice box, you will have two or more reeds sounding together for each button, so it is important that the gap for all the reeds on each button is set so that all the reeds speak at the same time, otherwise you will get uneven tremolo as first one reed speaks and then the second reed joins in a fraction of a second later.  

Ans.3
I've only done this once. I removed all the pallets from the rods and pulled off most of the old facing material with my fingers, then used a Stanley knife blade as a scraper to remove the residual leather/felt and glue. I finished off by gently sanding each pallet face just down to bare wood (but no further) by rubbing on a sheet of carborundum paper laid on top of a flat surface (a scrap piece of melamine-covered board). Clearly you need to maintain as flat a surface as you can on the pallet face, but if the replacement facing material is a felt/leather composite (such as Charlie Marshall sells), there is sufficient 'give' to accommodate minor departures from optical flatness.
« Last Edit: November 18, 2010, 03:06:19 PM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk
Pages: 1 2 3 [4] 5 6 7   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal