Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: scale length in diatonic bass reeds  (Read 1601 times)

0 Members and 1 Guest are viewing this topic.

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
scale length in diatonic bass reeds
« on: July 01, 2010, 07:07:05 PM »

I've always had mixed feelings about the scale length of the 1st ("bassi") and 2nd ("terzetti") reeds in a standard diatonic set, hand made or not. The length of the bass reed is somewhere between the 1st and 2nd reed in a standard chromatic set (Indeed, good old Nazzareno Carini, now retired, insisted in calling them terzetti and not bassi!). The difference between a diatonic and a chromatic 2nd reed is even more significant. I remember, though, comïng across some Mengascini boxes where that reed was significantly larger (the effect, however, was ruined by very small sound holes and pallets that didn't lift properly...).
In order to obtain a fuller bass-sound I'm planning an experiment with diatonic bass/terzetti reeds that match its chromatic counterparts. It was not quite easy to convince my supplier, but now these reeds are on their way.
As long as it's an 8 bass box I'm not too concerned about the minimal extra weight. Of course I hope to get a richer bass sound for less
effort... The ordered reeds are top notch quality, so I'm not unduly worried about the extra air either.
I'm looking forward to advice/comments/opinions, maybe someone out there has already tried a similar experiment?
Last not least: I have no intention to experiment with Helikon basses...
Logged

Lars

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 797
Re: scale length in diatonic bass reeds
« Reply #1 on: July 03, 2010, 10:32:07 AM »

I think I've had the same thoughts and issues - the low bass reeds not being "low" enough for my liking. The note was low, in terms of hertz, but the feeling was just not right.

I managed to find some old Paolo Soprani bass reeds from the 1920's, where the scale was close to a centimeter longer than similar reeds used in the 50's. The tongue of those old reeds were rather thin, and had a huge lump of lead on the tip. The pitch of the range of bass reeds in a set were shiftet a little down, so A became the lowest reed (on a C#/D set) and G the highest.

The reeds has now been arranged in a standard soprani setup - 2 bass reeds in 2 octaves, 2 shared between bass and chord, and 2 chord reeds (3rd and 5th) making both bass and chord 4 voice.

It really is a massive boost compared to the cagnoni TAM I had in the same box before. If I am to order reeds from a maker again, I really would prefer having the low A - makes a very distinct and wonderful difference to the playing style I play, with short sporadic basses.
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: scale length in diatonic bass reeds
« Reply #2 on: July 03, 2010, 03:49:03 PM »

Sounds encouraging. I too prefer the low A's, but as you point out, the standard scale length in diatonic sets just doesn't seem to support it. My Binci reeds had a ton of brass welded on to them, were relatively slow in responding and easily choked even with a reasonable opening between frame and reed-tip.
Logged

Lars

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 797
Re: scale length in diatonic bass reeds
« Reply #3 on: July 03, 2010, 07:54:32 PM »

I suppose it's different from box to box.

I found that it helps to get the huge reeds going to have them opposite the other bass (high bass) on the block - so the small would help get the big going. I also set them at a rather large gap, but they do not require that much air, actually. Those big reeds also have larger than usual holes in block and soundboard.
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: scale length in diatonic bass reeds
« Reply #4 on: July 03, 2010, 08:12:35 PM »

If I understand you correctly it's more or less what I've been doing, too. But anyway, now I'm looking forward to building new blocks with the (now larger) bass reeds in a 90 degree angle in relation to and on top of the other reeds. It wouldn't be my first flop, but then, surprisingly, every now and then some ideas really do work...
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal