Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3   Go Down

Author Topic: Making reed wax  (Read 16077 times)

0 Members and 1 Guest are viewing this topic.

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Making reed wax
« on: July 13, 2010, 07:07:53 PM »

Set up to make some reed wax this afternoon,

60g resin powder, 60g beeswax, 5ml olive oil

Heated the wax in a glass jar stood in a sucepan of boiling water (with a nice little ali takeway tray shroud to keep in the heat)

When melted, drizzled in the resin powder a spoonful at a time while stirring to avoid chilling the 'brew'

when all submerged, shot in the oil.

Heated, stirred, heated, stirred, stirred, stirred (ditto repeato for 3 hours)

when my patience finally ran out I had a thick gooey lump in the nice runny wax which felt like that pulled toffee and seemed to be getting stiffer (as I expect when making turners cement which this will be used for) and a mildly discoloured wax - with the resinous element extracted and cooled it looks like one of those dried figs or as Kim observed when she finally got into the kitchen to start tonights meal, some sort of animal dropping  ::)

Any idea whats gone wrong ??

First thought was I should have left the oil until last (have I made some sort of polymer ??)

Second thought, had my heat retaining shroud dropped condensate from the water into the brew

Final thought, do people usually  start with powdered or lump resin ?

Unless advised otherwise I shall try again by stirring lumps of resin into the hot wax!

Academic at present but what method of casting sticks is common ? I had corrugated some cooking foil with a view to pouring wax in the vees as I do when casting solder or turning wax - any other bright ideas ?

Note to Theo, if I had put some propolis in the mix I might have expected this, the jar of propolis on hand to add when the proper mix is poured satisfactorily so you may yet still be able to try some out........

Richard
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: Making reed wax
« Reply #1 on: July 13, 2010, 10:04:38 PM »

60g resin powder, 60g beeswax, 5ml olive oil
Unless advised otherwise I shall try again by stirring lumps of resin into the hot wax!
Academic at present but what method of casting sticks is common ? I had corrugated some cooking foil with a view to pouring wax in the vees as I do when casting solder or turning wax - any other bright ideas ?

Think personally that this is too much rosin.
Melt the rosin first - then add the wax.
Best way I have found to make sticks - Pour some molten wax onto a tray of hot water -  when cool you have a sheet of wax. Score it - chill it - snap it into sticks.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Making reed wax
« Reply #2 on: July 13, 2010, 10:12:04 PM »

I've mafecthe occasional bowl of gloop too. It seems to be less of a problem if you add the oil after the wax and rosin have melted together.

To make sticks I pour the wax into a flat container the slice with a sharp knife and straight edge.  The temperature has to be just right for this,  too cold and the wax is brittle and cracks as you cut,  too warm and the cut heals after the knife has passed.  A warm room temp seems to work so I'd guess about 20 to 25 C.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Making reed wax
« Reply #3 on: July 13, 2010, 11:40:43 PM »

Thanks both,

I had seen several ratios of rosin to wax in the old forum postings and since Theo and Rees of this parish indicate 50:50 is a good mix thats what I used, although I hadn't seen anything regarding which to melt into which, I had assumed the rosin would melt into the wax more easily than the reverse - Wrong !

Having tried to cut thicker wax cleanly before I hadn't considered cutting a thin sheet warm or casting it on a hot water bath and cooling, I was thinking of casting the finished sticks like you would cast your own foundation and I can see other applications for this  (:)

No progress on the old Hohner today - I had mistakenly thought at least some of the reeds would be fitted tonight and I've a visit to the hospital tomorow so probably Thursday before I get round to another meltdown session.

Will advise progress - or lack of >:E
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: Making reed wax
« Reply #4 on: July 14, 2010, 01:56:32 AM »

Interesting thread. Experimenting with resin recipes looks like loads of fun. There's also pre-mixed/oiled/formed Hohner reedplate wax available here:

https://www.shopssl.de/epages/es117831.sf/en_US/?ObjectPath=/Shops/es117831_stringsandboxes/Categories/%22Akkordeon%20Werkstoffe%22/Stimmplattenwachs

I'd be interested in making my own to compare the results with some "prefab" wax that is supposed to work as it should.

(The link is to an English translation of the page, and the original German page is here: https://www.shopssl.de/epages/es117831.sf/)

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: Making reed wax
« Reply #5 on: July 14, 2010, 01:57:12 AM »

Does pine rosin have a higher melting point than wax, and if so, shouldn't it be melted first?

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Making reed wax
« Reply #6 on: July 14, 2010, 04:49:17 PM »

Thanks for that, Charlie Marshall supplies an equivalent in the UK (as no doubt to several others)

The lignite resin, turpentine and other additives is an interesting departure from the mixes in the old forum threads.

Yes the resin does melt at a higher temp than beeswax

Having used a very fine resin powder, sifted from the lumps, the liquid poured off into a mould weighs 88g (original wax 60g) the resultant resin 'dried fig' is 25 which assuming no evaporation leaves 7g stuck in the bottom of the jar (with just under 5g of oil somewhere between the two) so obviously some resin has amalgamated with the wax.

I suspect people may start from a more granular resin or just plain lumps which means it does not gloop in a lump with relatively low surface area. While not specified in the recipes, the implication is that both are melted together and then after serious stirring finally amalgamate

Having got the 'why did it do that' bit between me teeth I shall try both resin powder first to melt and wax / lump resin together - My adding oil before all was fully mixed may well have had a negative effect - will report results as and when available.

As for lignite resin - well it'll have to go without !

Richard
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Making reed wax
« Reply #7 on: July 15, 2010, 10:19:17 PM »

Well, after some wax wangling experiments today I can report that wax first or (lump) resin first ends up with the same result, although with some liquid wax the resin seems to combine more easily - my first disastrous attempt would appear to be as a result of adding the oil before all the resin was combined with the wax and perhaps that it was powdered resin encouraged this to happen.

Olive or Linseed oils also appear to make no noticeable difference to the finished product, have yet to trial it.

Adding some propolis (5g to a 200g batch) resulted in another gooey blob which would not dissolve, with so little to start with and some wax left on the jar (which I neglected to weigh before starting) I cannot determine how much actually went into the final product but it is darker than the other 'brews' and noticeably more tacky at hand hot temperature.

Still trying to track down a CSR1504B or equivalent mains power regulator at a reasonable price so I can set my soldering / pyrography iron at an appropriate temperature to re set me reedplates, corners of bellows leathers to have a drop of neatsfoot oil to soften them and hopefully i'm not to far from having a tune out of the box, however untuned it may be....

Oh and invested 6 quid in a bottle of nickel plating solution for the 'furniture' - anyone had any experience of 'pen plating' with Nickel ?

Richard
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Bill the Farmer

  • Not quite so
  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 497
  • Hohner Club, Liliput...
    • Bill Farmer
Re: Making reed wax
« Reply #8 on: July 18, 2010, 09:33:50 AM »

Still trying to track down a CSR1504B or equivalent mains power regulator at a reasonable price so I can set my soldering / pyrography iron at an appropriate temperature to re set me reedplates...
Richard

I've got a very old Weller fixed temperature iron which is far too hot for reed wax, so I made a bit extension out of copper wire which gets down to about the right temperature.
Logged
Bill of Old Radipole Village

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Making reed wax
« Reply #9 on: July 18, 2010, 12:51:54 PM »

All this talk about which component to melt first reminded me of a "friend" who decided to deep fry some chicken.  The chicken was excellent, but the contamination of the deep fry oil with chicken fat meant that it could never again achieve the heat required to cook chips!  So I guess it does matter.

Rob.
Logged

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Making reed wax
« Reply #10 on: July 18, 2010, 02:09:49 PM »

Bill,

Posted on the 'Old Hohner' topic last night, I made up a chopper similar to a dimmer switch which while not temperature controlled, kept the iron (a small Antex) down at an ideal heat. Had some noise from the re assembled box but have a few reads not speaking properly, when I've sorted those, will point it at your tuner to see what else needs to be done.

Rob,

If I were melting metal, the lowest temperature would be the last into the pot, however, I feel that with this brew, melting the beeswax first and then drizzling the resin chunks in afterwards gave a quicker absorbtion than resin first due to its viscosity and tendancy to become a stick blob - probably due to the surface area available for melting, having tried a stick of both when refitting the reeds last night there is no perceptible difference between them in use and I guess if they last as long as the original wax which is/was in perfect order I'll be long gone before finding out how durable it is.......


Richard
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: Making reed wax
« Reply #11 on: July 18, 2010, 04:50:42 PM »

I use a stylus for hot wax art, it is obviously calibrated to melt wax! I did two complete reed replacement jobs (4-voice and 2-voice 1-row boxes) and it worked like a charm. Cost me only $27 in a craft store.
Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Making reed wax
« Reply #12 on: July 18, 2010, 08:56:38 PM »

I use a stylus for hot wax art, it is obviously calibrated to melt wax!


While my soldering iron isn't calibrated or temperature controlled in the thermostatic sense it is a miniature for fine soldering jobs with a thinned down bit end I use for signing the odd bit of woodturning (that is good enough to pass on) with my new power controller it is very docile to use on wax  (:)

Forgot to mention previously, on speaking with a beekeeping friend regarding casting wax sheet over hot water for sticks, he suggested I pass on the information not to try putting wax, at any temperature, through a set of pasta rolls to get thin sheet or strips, it goes in OK but his experience of getting it out again was not good, very not good :'( :'(


On wax composition, the top three pairs of reeds in my old Hohner currently under repair, I have left in their original wax, where I have run the iron into it, the percentage of Rosin appears to be very high, nearer 100% than 50% would be my guess.

Richard
« Last Edit: July 18, 2010, 09:24:12 PM by Broadland Boy »
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Making reed wax
« Reply #13 on: August 08, 2010, 02:34:04 PM »

Interesting thread. Experimenting with resin recipes looks like loads of fun. There's also pre-mixed/oiled/formed Hohner reedplate wax available here:

https://www.shopssl.de/epages/es117831.sf/en_US/?ObjectPath=/Shops/es117831_stringsandboxes/Categories/%22Akkordeon%20Werkstoffe%22/Stimmplattenwachs

I'd be interested in making my own to compare the results with some "prefab" wax that is supposed to work as it should.

(The link is to an English translation of the page, and the original German page is here: https://www.shopssl.de/epages/es117831.sf/)

Nielsen told me that he uses carnauba wax as part of his own mixture, but wouldn't say what else was in it :-(

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Making reed wax
« Reply #14 on: August 08, 2010, 02:46:53 PM »

It is tempting to make your own wax recipe, but the trouble is you really need to be around for a couple of decades to see if it lasts as long as the tried and tested mixes.

I wonder what the Carnuba wax added to the plot?   It is common ingredient of wax polishes because it is harder than beeswax and easier to buff to a high gloss.  I believe that the blue/green coloured wax I've seen on some boxes is from Neilson.  Its rather soft, and I suspect contains a proportion of paraffin wax which would give it a lower melting point, which is increasing the risk of dropped reeds if the box is left in a hot place.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Making reed wax
« Reply #15 on: August 08, 2010, 02:52:32 PM »

It is tempting to make your own wax recipe, but the trouble is you really need to be around for a couple of decades to see if it lasts as long as the tried and tested mixes.

I wonder what the Carnuba wax added to the plot?   It is common ingredient of wax polishes because it is harder than beeswax and easier to buff to a high gloss.  I believe that the blue/green coloured wax I've seen on some boxes is from Neilson.  Its rather soft, and I suspect contains a proportion of paraffin wax which would give it a lower melting point, which is increasing the risk of dropped reeds if the box is left in a hot place.

The green wax is Nielsen's, he does this so he can tell which reeds he's previously worked on. I've never had any of these reeds drop off at high temperatures.

If mixtures of reed waxes behave like mixtures of metals in alloys, maybe the hard carnauba wax adds high temperature strength and allows softer wax to be used as the main proportion to give better mechanical strength (resistance to fracture under shock/vibration) ?

Of course Nielsen's been around for rather more than a couple of decades, so I expect he knew what was doing with wax :-)

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Making reed wax
« Reply #16 on: August 08, 2010, 03:01:30 PM »

It's difficult to know what to believe of Nielsen's stories, but he told me he talked to industrial wax manufacturers and the result was that he developed a wax that had no plant based ingredients (based on mineral oil products, I suppose) which made it longer lasting. Natural waxes have ingredients that "go off" with time; his don't (or don't so much).
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Making reed wax
« Reply #17 on: August 08, 2010, 03:16:43 PM »

no plant based ingredients


Hmm,  carnuba is a from plant origin, but beeswax is not!  I wonder what he uses to replace the pine rosin?

To assert that plant based waxes "go off" in time and synthetic or mineral waxes don't seems rather a sweeping generalisation. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Making reed wax
« Reply #18 on: August 08, 2010, 05:15:11 PM »

OK, don't quote me on the details.  :|bl I do remember him saying:
(1) that "traditional" waxes made from natural ingredients based on living things were fine to start with but went wrong (usually going hard and brittle, I think) after years of use.
(2) That his approach resulted from talking to industrial wax makers/users and that his wax lasts longer.

Maybe he does use beeswax or wood resin, and it's some other ingredient that he's changed.
Needless to say, he wasn't too explicit about exactly what he used, and he's hard enough to understand at the best of times...
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Making reed wax
« Reply #19 on: August 08, 2010, 05:55:25 PM »

Is beeswax (technically) "Veggie" ?  :|glug

In that it originates from the nectar collected from plants, some of which may be vegetables yes Chris, but bees secrete it from glands after ingesting either their nectars or the sugar solution we wicked bee keepers give them to make a comb with if they are from a swarm or colony division, or placate them with if we steal their hunny, so for purposes of Veganism it is an animal (insect) derived material, how this equates to drinking milk but not wearing leather I have no idea, or (unusually) opinion.....................

Anyhow as I understand from Prof Hawking* that all come from stardust anyway ;D

Some of the modern microcrystaline waxes are beginning to gain favour as protective coatings - Given the track record of the various grades of Ensis fluid and Waxoyl type of products there's plenty of past history for their durability and resistance to drying out and cracking but not so much on a timber substrate - if it were an issue then sealing the wood surface of the reedblock would reduce drying but I suspect that being able to penetrate the surface grain is part of the adhesive effect.

Having seen some trade 'offerings' of refined beeswax compared with mine, part of the processing bleaches the colour which reduces the propolis and pollen 'contamination' and it is no where near as sticky when melted, if you are making your own reed wax, get the wax from as close to the bee as you can - would you agree Theo ?

I have a lump of beeswax from my grandfather, who kept bees in the 1930's, he, my dad and now I use it for waxing thread for shoe / leather repairs, its surface is filthy but the wax is still fresh and when you draw a thread through it you can still smell the hive, unfortunately heating old reedwax the smell of the resin tends to dominate but I think you can still smell the wax, which means the volatiles are still intact to a large extent.

I like the idea of colour coding wax, like the minute watchmakers marks indicating their contribution to the history of a timepiece.

Richard

(who tried to run me over in his chariot in Cambridge one evening when I wasn't even carrying a melodeon)
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa
Pages: [1] 2 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal