Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Lester Bellows?  (Read 2137 times)

0 Members and 1 Guest are viewing this topic.

RGF

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 214
Lester Bellows?
« on: July 14, 2010, 04:54:58 AM »

Hi, All.

The photo of Al's Glory Harp caught my attention, as it looks so much like the Lester I've had waiting here in the shop for so long. Then -- lo and behold -- I see a photo of an actual Lester!  So I've finally taken this old beater down off the shelf in hopes that I might resurrect it and send it off as a gift to an old friend I haven't seen in years. (Heard that he's living in Washington state, in an old Airstream trailer, and working on wooden boats. Kind of just screams out to me, "And I need a melodeon, even if I don't know it yet!")

So, the weak link in this one is the bellows, which are just about totally knackered. Half the gussets are split and covered over with celo tape. Easiest thing for me to do would be to find a halfway decent set from someones junkyard. I really don't want to get into bringing this set back around, and I hardly think it would be worth the effort. Anybod got a more workable set lying about that they would care to sell? Or is there some easy patch for this sort of thing that I haven't heard about yet? Or if someone has a set that's close in size, I could graft it on to these frames. Other ideas?

And, as an aside, I notice that the Lester was imported by a New York firm known as B&J. Now there was once a B&J (Burke and James) that made view cameras, the bellows type, with wood frames and so forth, and I can see how there could well be some manufacturing crossover here. Anybod know anything about B&J? The one thing I know is that the cameras were not too highly regarded, and were sometimes referred to as "Bunk & Junk"!

Bob

Logged

RGF

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 214
Re: Lester Bellows?
« Reply #1 on: July 14, 2010, 05:08:08 AM »

P.S.

I guess some dimensions might be hulpful, no?  The outside measurements of the frames is 5.75" x 11", or about 14.5 x 27.5 cm.  The frames do not mate with the cases in the more modern manner of plugging in and then held with pins....They are just flat faces, positioned on the instrument ends and secured with four screws.
 
Bob
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Lester Bellows?
« Reply #2 on: July 14, 2010, 08:42:01 AM »

If you do find a bellows of the correct dimensions the best way to fit it is to glue the 'new' bellows onto the old frames, not a difficult job, and it means that all the screw holes will line up properly.   You might also re-cover the bellows frames with new material that laps over the joint between bellows and frame, a good material for this bookbinders buckram.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

boaz-1990

  • Member
  • *
  • Offline Offline
  • Posts: 6
Re: Lester Bellows?
« Reply #3 on: July 14, 2010, 08:58:15 AM »

If all else fails, and you are good with your hands you could rebuild them from scratch. I've just started building a set and have found it surprisingly easy so far (fingers crossed). This way you can get the exact dimensions you want, and like Theo said stick these new bellows to the old frames if they are intact, and seal with buckram. Job Done!

Boaz
Logged

Malcolm Austen

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 495
  • any old hohner
Re: Lester Bellows?
« Reply #4 on: July 14, 2010, 08:32:13 PM »

Lester Bellows
Not at our session he don't
Logged
aka malodeon
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal