Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Confession is Good for the Soul!  (Read 5477 times)

0 Members and 1 Guest are viewing this topic.

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Confession is Good for the Soul!
« on: August 01, 2010, 04:48:52 AM »

So ashamedly I must confess my guilt.  Yes it was I that bought that Double Ray Deluxe so prettily dangled before my eyes a month or so ago.  Below is the evidence!  My question is about the reeds.  They are pretty rusty.  Do I make the effort to remove the rust and fully restore the reeds and blocks or do I simply replace them with some Machine or Dural Italian reeds?  The box truly deserves to be fully restored but the reeds are certainly rusty.  Any advice much appreciated.  Anyone know of a 12 step group for my kind of affliction? 
Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

HallelujahAl

  • Guest
Re: Confession is Good for the Soul!
« Reply #1 on: August 01, 2010, 07:30:33 AM »

well done ajay! Some folk had assumed it was me that had gone for it. Anyway, the reeds don't look too bad to me, i've seen worse anyway. I think they'd clean up quite nicely. Far rather to stick with the original reeds don't you think? Regards al
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Confession is Good for the Soul!
« Reply #2 on: August 01, 2010, 08:17:09 AM »

Al's right those reeds don't look too bad to me,  and they are some of Hohners best reeds with the Hohner name stamped on every plate.

Just ask here if you need any advice on how to do the cleaning.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Confession is Good for the Soul!
« Reply #3 on: August 01, 2010, 09:30:03 AM »

In the photo of the reed blocks, I notice that the air holes on the base have a slot connecting the two sets of holes. I've not seen that before - is that a feature of the Double Ray?
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Re: Confession is Good for the Soul!
« Reply #4 on: August 02, 2010, 01:57:07 AM »

Yes Theo I need your advice vis-a-vis the rust and the rest of the reed blocks, particularly what appears to be "rivets" holding the reeds in.  There are also what appears on some of the bass reeds and other treble reeds to be brads (nails) pinning the reeds in including wax.  Should I remove the pins/brads and just rewax the reeds in alone?  Also how do I get rid of the rust.  I have searched the forum but found no information regarding actual removal of rust. 

My first instinct with this box is to send the reeds off and have you or my other box tech do the dirty work but then I think this might be a perfect box to be my fall-winter project.  I have never tackled reed work and tuning before.  What's your advice?

--Drew
Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Confession is Good for the Soul!
« Reply #5 on: August 02, 2010, 09:11:41 AM »

The reed tongues are attached to the reed plate with rivets, but its quite unnecessary,  and in fact a very bad idea, to remove the rivets to clean the reed tongues. First the reedplates must all be removed and all the old wax cleaned off, and the old valves should all be removed and discarded. You need to find or make some trays where the reeds can be laid out in sets.  I use a variety of mechanical methods to remove rust - polishing block, abrasive paper, scotchbrite, sanding pen, small screwdrivers as scrapers etc. Its not easy to explain the details in words.  I think I need to take some more photos.

The nails that are used in combination with wax to hold the reed plates are in my opinion quite unnecessary and can be discarded when the reeds are re-waxed. Hohner don't use nails on modern instruments, and neither do any Italian makers as far as I know.

If you want to try doing some of this work yourself I would suggest starting with a model with fewer reeds, and definitely one that is less of a rarity.  Anyone tackling a restoration job like this will be learning as they go and they and will surely be learning from mistakes.  Anyone who tackles a first restoration and makes no mistakes is either a genius (:) or is not smart enough to spot the mistakes!  :(
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Re: Confession is Good for the Soul!
« Reply #6 on: August 02, 2010, 03:39:30 PM »

Thanks Theo,
I might as you say find another accordion as my first reed project.  It really is a beautiful box and rare as you say (not in the ebay sense).  As I look at the reeds I do find myself a little daunted. 

--Drew
Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Confession is Good for the Soul!
« Reply #7 on: August 02, 2010, 03:47:21 PM »

Thanks Theo,
I might as you say find another accordion as my first reed project.  It really is a beautiful box and rare as you say (not in the ebay sense).  As I look at the reeds I do find myself a little daunted. 

--Drew

A relatively benign method of rust removal is with a draftsmans glass fibre pencil, praps Theo has experience of how much the tone may be altered and either endorse or warn against this.
Steel or ali beer / coke cans if 'dismantled' carefully with scissors (warning edges may be very sharp) yield very thin material which can be cut into suitable sized stripsto support the reeds, I would rub all round the cut edges with the scissor handles or similar to flatten any burrs from the scissors.

HTH

Richard
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Confession is Good for the Soul!
« Reply #8 on: August 02, 2010, 04:36:53 PM »

Yes the glass fibre pencil works well,  removed rust, but not steel, though will remove metal from brass reeds.  I don't use them much any more because of the very nasty fibrous dust that that they put into the air.  I now use a polishing block instead.  No airborne dust.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Confession is Good for the Soul!
« Reply #9 on: August 02, 2010, 05:46:30 PM »

I've not tried those polishing blocks Theo, on Wednesday I have a hospital appt. and had thought of making one of my rare trips to Maplins en route, so will see if they have any.

The residual glass fibre is not nice if it gets into bearings (as I know to my cost) and a real pain if it gets into the skin, thankfully I have found the fibres are heavy enough to fall quickly rather than getting into the airstream.

I use a saturated solution of table salt in white vinegar for removing rust and oxide films from fine steel parts but I would not try it on reeds as it would wick between reed and plate, so could not be neutralised or dried.

The other thing I use on both metals and wood is the grey grade of scotchbrite pad, equates to about 1000 grit and while quite gentle, is the best way I know of to take a tenth of a thou off something in the lathe in metal, like a shaft or rod.

There is an old fashioned method which gunsmiths use, instead of the traditional blueing, if you have a rusted surface (they do it by acid fuming to get an even finish) and boil the result in plain water it converts the rust to a brown iron oxide, dunno what the heating would do to a reedplate but not only are you leaving the same amount of weight in the reed -actually just a shade more, but adding a rust proof surface - if it is rusted all over.

Anyone brave enough to try it and report results ??

Richard
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

oggiesnr

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 995
  • Dino BPII, Alfred Arnold Bandoneon, Loffet G/C
Re: Confession is Good for the Soul!
« Reply #10 on: August 02, 2010, 10:16:29 PM »

Aluminian Oxide sand paper is available down to 2,400 grit, try your local car paint supplier.

Steve
Logged

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Confession is Good for the Soul!
« Reply #11 on: August 02, 2010, 11:55:20 PM »

Aluminian Oxide sand paper is available down to 2,400 grit, try your local car paint supplier.

Steve

Yup and I often use it for finish honing plane blades or turning tools with (on a surface plate or sheet of glass), I prefer the scotchbrite for turning as it conforms beautifully on the outside of irregular stuff handheld (also a barrier for frictional heat) but folded AlOx sheet is great for details or where a corner could get rounded.

I can't remember the trade name now but there is a range of US made polishing media which goes down to 10000 grit, sort of plastic cloth backing and I suspect Cerium Oxide abrasive - I have used it for final polishing of a machined near flat glass (!) lens for an I/R scanning head, thankfully that R&D project never made it into a production version  ::)

Thanks for the heads up though Steve - the collective knowledge of this forums members outside the melodeon sphere is as stunning as the on topic knowledge.

I'm currently working on a power supply and 'pen' so I can re plate the hooks on the ancient Hohner (so badly rusted they have been wire brushed and Jenolited) with Nickel - I've done the odd bit of immersed in a bath electroplating but this is my first foray into this method - if it works I have stacks of stuff which will benefit, old cameras, engine indicators, gauges - likely to be a world shortage of Nickel soon  (:)

Richard

BTW Thanks for the comment back on the Hohner 'taming' wood query Theo, I mentioned the Ash in case it was a wood you had used, I think it will be similar to R Cedar in its 'crushability factor' but won't smell as nice when fresh.
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Confession is Good for the Soul!
« Reply #12 on: August 03, 2010, 12:45:07 AM »


There is an old fashioned method which gunsmiths use, instead of the traditional blueing, if you have a rusted surface (they do it by acid fuming to get an even finish) and boil the result in plain water it converts the rust to a brown iron oxide, dunno what the heating would do to a reedplate but not only are you leaving the same amount of weight in the reed -actually just a shade more, but adding a rust proof surface - if it is rusted all over.

Anyone brave enough to try it and report results ??

Richard

 I would avoid immersing reeds or boiling them. The early process (before 'blueing') was called 'browning'. It was simply culturing a very fine layer of iron oxide (or rust) by repeated treatments of rust-causing solutions, drying, and then burnishing with a wire brush or similar. These finishes (on antique firearms) were highly prized and woe to the uneducated collector of a firearm who removed the brown finish to bare metal! The purpose of the oxide coating on steel is to prevent further oxidation. The blue color you sometimes see on steel reeds is an oxide coating, very similar to the blueing used on firearms or other machine parts, especially springs.
 
    Rust on reeds can be a concern depending on the degree and depth. If it is deep enough to make visible pits, then it's trouble, as the cross section of the reed is altered, structurally weakened, and the mass of the reed will have changed, altering pitch. If the rust is very fine, then it can be burnished to a brownish-gray stain that is actually an oxide coating. Even if the stain is splotchy or uneven, it is far less worrisome than pitting.

 The way I accomplish burnishing is by using a small twist of 0000 steel fur, similar to that used on cabinet finishing. The reed tongue must be well supported by a shim or similar device. Lightly rub the rusty area along the reed with the steel fur until you have a shiny gray/charcoal colored surface where the rust patches were. Try to stay clear of where the reed fastens at the rivet area, as the fibers of the fur can get lodged there. If there is rust around the rivet, use a dremel tool (lightly!) with a fine wire wheel at low speed to get that area (wear eye protection!). When the reed seems clean enough, then apply some light compressed air to blow debris away from the reed and frame. I use a small can of compressed gas made for blowing out delicate mechanisms called "Dust Off". A 'pipe cleaner' can be used to sweep out residue as well.
  
  This is a method that has worked for me;...... your results may vary. I try to stay away from chemicals or harsh abrasives. Always exercise caution. It is not uncommon to find small amounts of rust in any free reed instrument that has lived in a humid climate. It's not the end of the world. As for rust prevention, I have some theories on that, but do not wish to share them because they are not fully tried and true. Any feedback welcome here.  ;)
« Last Edit: August 03, 2010, 02:26:38 AM by j.w.forrest »
Logged

strad

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 418
Re: Confession is Good for the Soul!
« Reply #13 on: August 03, 2010, 11:10:21 AM »

The American polishing item referred to by Broadland Boy is almost certainly Micro Mesh
A quick Google showed that Axminster and others stock it. It goes from 1500 to 12000 grit and is used for taking scratches off aeroplane windows amongst other things. There is a Hobby Kit that I have which has small rectangles of the various grades and it polishes to an amazingly smooth surface.

Nigel
Logged

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Confession is Good for the Soul!
« Reply #14 on: August 03, 2010, 01:32:33 PM »

The American polishing item referred to by Broadland Boy is almost certainly Micro Mesh
A quick Google showed that Axminster and others stock it. It goes from 1500 to 12000 grit and is used for taking scratches off aeroplane windows amongst other things. There is a Hobby Kit that I have which has small rectangles of the various grades and it polishes to an amazingly smooth surface.

Nigel


Thanks for the tip. This looks to be a very useful product. Have not encountered it yet in shops... :o
Logged

Gandy

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 407
Re: Confession is Good for the Soul!
« Reply #15 on: August 04, 2010, 07:18:36 PM »

Also 3M "Lapping Film", available up to (down to?) 6000 grit from www.workshopheaven.co.uk
Logged
Tony S

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Confession is Good for the Soul!
« Reply #16 on: August 04, 2010, 11:38:41 PM »

Thanks Strad, Micromesh it was - I've not had an Axminster cat. for a while, I expect the growing interest in turning pen bodies from plastics has triggered their stocking it.

JWW - I was not advocating wholesale boiling of rusty reeds for the reasons noted which you have re enforced ;)

My understanding is that browning and blueing are both oxide films as opposed to the exposed powdery rust, I'm not certain of the chemical reaction which occurs with browning but the finished surface gives a coating resistant to further atmospheric rusting in the same way that blueing does, blueing occurs at a higher tempering temperature which may draw the temper of the reed material. Howsumever both may be used a method of finishing furniture such as latches, hooks, corners etc. I had an elderly Martini Henry .45 cal rifle in the workshop at the weekend - of Rourkes Drift vintage and the browning on this, while polished off in the high touch areas is as good as the day it was done

Tumbling / rumbling in something like fine walnut shell is often used for dry finishing of parts, as is very gentle 'blasting' with baking powder / bicarbonate of soda.

Your canned dry air for dusting tip is useful for those without wind compressing gear - most often seen as an aid for cleaning computer bits and far easier to handle than a bycycle pump  :D

Gandy, have not tried 3M lapping film and if I don't get round to finishing my surface grinder may well look for some.

Richard
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Confession is Good for the Soul!
« Reply #17 on: August 04, 2010, 11:50:22 PM »

I seem to recall that gunsmiths carry tins of a blueing compound which is simply painted onto clean, degreased steel and chemically treats the surface, leaving a finish indistinguishable (to the eye) to traditional blueing.  It's usually used to finish one off parts or touch in worn areas.  I had cause to specify it to replicate "factory parts" being supplied to FoMoCo after filing bits down to fit!

Would this be a suitable treatment for reeds, I wonder?

Rob.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Confession is Good for the Soul!
« Reply #18 on: August 05, 2010, 12:03:58 AM »


Would this be a suitable treatment for reeds, I wonder?

Rob.

I don't think any "treatment" is  necessary.   Just clean off the loose rust and finish off with a medium/fine abrasive to leave a smooth surface and your old Hohner will be ready for another 50 years of playing.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Confession is Good for the Soul!
« Reply #19 on: August 05, 2010, 12:21:23 AM »

I seem to recall that gunsmiths carry tins of a blueing compound which is simply painted onto clean, degreased steel and chemically treats the surface, leaving a finish indistinguishable (to the eye) to traditional blueing.  It's usually used to finish one off parts or touch in worn areas.  I had cause to specify it to replicate "factory parts" being supplied to FoMoCo after filing bits down to fit!

Would this be a suitable treatment for reeds, I wonder?

Rob.

Theo is right Rob, and while the original blueing from tempering the hardened reeds will act as a barrier the cold blueing compounds will do no good and are very nasty (Seleneum and Arsenic amongst other heavy metals IIRC) at least the ones I have used are and suggested adding a rustproofing compound over them. I've used them in the past to patch up guns and watch / barometer / gauge hands with very poor results over time.

You may laugh but if I have to finish something now which needs blueing and either I can't be ar**d or it is not capable of being hot blued, I use either a black or a blue permanent marker pen, which deposits a nice film which is pretty resistant to rust or steam - I doubt it would do any harm to reeds and if living or playing in a damp environment might hold back the red stuff  8)

Its also a long time since I bought any layout blue as a pen marker is just soooooo handy and works just as well if you want to take half a tenth of something with a file.  (:)

Richard
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal