Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: my pokerwork refurb  (Read 2676 times)

0 Members and 1 Guest are viewing this topic.

tedrick

  • Guest
my pokerwork refurb
« on: September 16, 2010, 12:30:09 AM »

Hey guys -
so I wasn't able to part with that cute little presswood a while back - I had it retuned to b/c instead -

while the clacky keys and down the hole buttons are quaint for a little while, I realize that if I'm really going to enjoy playing this little guy, I'm going to need to address the keyboard --

Is there a thread describing how to place felt below the button arms to control the amount of travel in the buttons?

(I'll be in touch Bob)

Reed

a couple vids of how the box sounds now:

http://www.youtube.com/watch?v=vuS_BgwSrys
and
http://www.youtube.com/watch?v=syBp7pWjdXw
Logged

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: my pokerwork refurb
« Reply #1 on: September 16, 2010, 12:52:26 AM »

I highly recommend placing a wooden bar under the levers so nicely depicted here by Theo: http://www.facebook.com/album.php?aid=109685&id=709188166&l=c564b24e38.  In my opinion, having tried both, it's much more effective than felt under the buttons for a pokerwork.  If you combine that with new felts and leathers on the pallets the clacking will disappear and it will be a joy to play.
Logged

tedrick

  • Guest
Re: my pokerwork refurb
« Reply #2 on: September 16, 2010, 03:31:30 AM »

Very neat! I'm glad I asked! This means I won't have to saw apart the fingerboard enclosure!
Thanks!
Logged

tedrick

  • Guest
Re: my pokerwork refurb
« Reply #3 on: September 16, 2010, 12:20:31 PM »

Hi Guys -
so looking at the keyboard assembly, I see how I can block the travel distance of each arm - very clever putting the stop point at the hinge instead of under the button - looking at my hohner it looks like the amount of button travel required to lift the pallet to the desired point is level or just a tiny bit below the keyboard surface (or into the hole)

My next question is: I would like to raise initial button height just a tad so that when the button is pressed down to the stop, the amount of travel is enough to lift the pallet the necessary amount to let air in - but button travel stops with the top surface of the buttons just above the keyboard surface - so my finger does not touch the keyboard surface or go down into the hole --

to make this adjustment, would I bend the arms back and up?

Thanks,
Reed
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: my pokerwork refurb
« Reply #4 on: September 16, 2010, 01:10:16 PM »

to make this adjustment, would I bend the arms back and up?

Yes
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

tedrick

  • Guest
Re: my pokerwork refurb
« Reply #5 on: September 21, 2010, 08:43:05 PM »

ok, so I have addressed the button travel issue by installing a temporary stop block under the arms - now for the infernal clacking of the pallets -

can I re-pad the pallets, or do I need to make new ones?

Thanks,
Reed
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: my pokerwork refurb
« Reply #6 on: September 21, 2010, 09:03:06 PM »

You certainly can re-pad the pallets.   For quietness use leather with a layer of felt underneath.   Take the pallets off the arms, pull off the old leather and sand smooth before gluing on the new material. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: my pokerwork refurb
« Reply #7 on: September 21, 2010, 09:06:25 PM »

.... now for the infernal clacking of the pallets -

can I re-pad the pallets, or do I need to make new ones?
I resurfaced the pallets on my Erica, using a 2.5 mm thick felt/leather composite, which I got from Charlie Marshall.
This stuff HERE.

The reduction of pallet noise was dramatic. Definitely worth doing.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

tedrick

  • Guest
Re: my pokerwork refurb
« Reply #8 on: September 21, 2010, 09:12:07 PM »

ah! OK - great!
so carefully "break" the pallets off? any tips on how to remove the pallets without damaging them?

Thanks!
Reed
Logged

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: my pokerwork refurb
« Reply #9 on: September 21, 2010, 09:56:56 PM »

ah! OK - great!
so carefully "break" the pallets off? any tips on how to remove the pallets without damaging them?

Thanks!
Reed

I've used a razor blade/craft knife to scrape away some of the adhesive, then rocked the pallets back and forth until they came off.

Be sure to glue the felt to the shiny side of the leather.
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal