Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Daft Hohner Project...biting off more than I can chew?  (Read 3922 times)

0 Members and 1 Guest are viewing this topic.

Jon Loomes

  • Performer, Recording Engineer, Luthier.
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 115
  • Non plaudite. Pecuniam jacite.
    • www.jonloomes.com
Daft Hohner Project...biting off more than I can chew?
« on: September 25, 2010, 11:02:43 AM »

Ok....

As the Music Room's melodeon lackey, I work surrounded by boxes I can't afford.  I sold my decent boxes a while back for reasons too depressing to go into here, but I'm starting to gig again and will need a box sooner or later.  So...I'm having a go at a rebuild/customisation type project. All opinions on this greatly welcomed. 

Old German pokerworks: Bloody marvelous, Ideally, I'd really like 12 basses.  Can I rip the bass mechanism out of a corona and modify the levers? I think there should be enough room for the pallets etc.

Now, I've got a very pretty carcass off a Student 1 accordion - Tyrolean Pattern, cream with red, green and gold, you know the one...  Same dimensions as a pokerwork, but with the bass rows slightly offset.  I guess I'm going to have to fill and re-drill and make a new (whatever you call that raised platform thing that the inner row of basses go through).

I'm guessing that the big job with this will be making new soundboards with holes cut in the right places for melodeon reedblocks.  Irritatingly, as an accordion it has a 22 key right hand - so 22 holes in the board - It'd be great if I could just shut one of them off, but does anyone know if the holes are centred the same?  After all, it would make manufacturing sense if the Student 1 used more or less the same factory templates as the diatonics.

Many thanks,

Jon

waldoB

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 126
Re: Daft Hohner Project...biting off more than I can chew?
« Reply #1 on: September 25, 2010, 03:57:08 PM »

Mike Rowbotham in St. Ives has done just that, there's a picture on his website. Not with the 12 bass though....

Good luck
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Daft Hohner Project...biting off more than I can chew?
« Reply #2 on: September 25, 2010, 04:08:17 PM »

Now, I've got a very pretty carcass off a Student 1 accordion - .....

Simon Ritchie has one done like this.  I recall him saying that it was a huge amount of work and he wouldn't want to do it again!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Microbot

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 345
Re: Daft Hohner Project...biting off more than I can chew?
« Reply #3 on: September 25, 2010, 05:32:22 PM »

Hi Jon et al

first off, you know you can find the occasional 2-row with 12 basses - they are pre-pokerwork and either pressed wood or black/gold pre-pokerwork (what I call 'Seashells' pattern - see middle box middle row of website). Also, the occasional perloid instrument. I've several 12 bass instruments at the moment.

As regards the Student 1 conversion, I'd encourage you to have a go - I'm making a second one of these at the moment, the first was so good. Fabulous casing and great sound. I used reeds from a C/F box rearranged for D/G - not the original Accordian reeds. Also, don't worry about the extra holes/reedblock space - I saw it as a 'plus', allowing me to fit an additional button low down on the G-row - I have low B/C on that, with the usual accidentals in the usual positions. There's a photo on my website showing my 22 button Student 1 melodeon.

As regards fitting 12 basses, you've got to source bass and chorus reedblocks plus action mechanism - a good source is an old Student 2 Piano Accordian. I've not done this on a pokerwork, but I have on several Erikas. There are 3 ways to go - one is to block off the original soundboard holes and re-drill. A second is to cut out the old soundboard and graft in the soundboard from the Piano Accordian - after all you're raiding it for most of its bass end - might as well have the soundboard too! -Fitting is easier than you might think. The third approach is to accept the soundboard holes already in the instrument and drill additional ones for the 4 extra basses. It's do-able on an Erika (just) but I'm not sure about a pokerwork size instrument. You get issues with positioning and contact with the internal folds of the bellows. I think inserting the 12-bass soundboard from the P.Acc is the most effective/easiest way to go.

Send me a PM and I'll give you my phone number; we can have a chat about the project if you like.

cheers

Mike R
Logged

Andy Simpson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 938
Re: Daft Hohner Project...biting off more than I can chew?
« Reply #4 on: September 25, 2010, 07:32:37 PM »

Am I correct in thinking that our Rees did Simon Ritchie's Student 1 conversion?.

I don't know exactly how it was done but Kepa Junkera has a 12 bass Pokerwork so it is possible.

I've had an Erika waiting for a 12 bass conversion for some time now and I've got to get on with it now that I've got no boxes to play, I just need to get hold of a Corona II bass mechanism. I'm going to make new blocks from scratch rather than trying to find some that fit, they shouldn't be too hard after this silly 8-string baritone guitar some nutter convinced me to make. ::)
Logged

Jon Loomes

  • Performer, Recording Engineer, Luthier.
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 115
  • Non plaudite. Pecuniam jacite.
    • www.jonloomes.com
Re: Daft Hohner Project...biting off more than I can chew?
« Reply #5 on: September 30, 2010, 07:09:35 PM »

ok...so far so good.  I've got a student II bass end. Looks like it should fit quite easily and I think I'm going to go with grafting the board rather than swapping all the bits.  The thing that has me stumped is, how to get those thermoplastic buttons off without breaking them or pouring hot water into either of the two boxes that I've got sprawling over the kitchen table?  Any ideas, or should I just snap the bloody things?

Cheers,
J

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Daft Hohner Project...biting off more than I can chew?
« Reply #6 on: September 30, 2010, 07:30:40 PM »

Do you run to a hot air gun in your kit or know someone who has John ?

A bit of kitchen foil to act as a bib round the stems would help preserve the finish (of the box, not buttons)

HTH

Richard - currently torturing apples with a ten ton jack  :-X
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Jon Loomes

  • Performer, Recording Engineer, Luthier.
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 115
  • Non plaudite. Pecuniam jacite.
    • www.jonloomes.com
Re: Daft Hohner Project...biting off more than I can chew?
« Reply #7 on: September 30, 2010, 07:37:56 PM »

Now that's not a bad idea.  I don't have a hot air gun unfortunately, but following the same line of thinking, maybe a soldering iron applied to the levers would be enough to transfer the required heat into the buttons. Trouble is, my soldering iron is many miles away...

Nicky Clarke ceramic hair straighteners it is...

Cheers,
J

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Daft Hohner Project...biting off more than I can chew?
« Reply #8 on: September 30, 2010, 07:46:33 PM »

Nicky Clarke ceramic hair straighteners it is...

Cheers,
J
You silly twisted boy  >:E

Anything with a flame is likely to damage, wot about a turn of bootlace or string round the stem, held reasonably tight and 'floss' it until the friction either warms it to plasticity or it ignites the firelighters which should be inside ?

Can't think of anything else - Apollo 13 might not have made it back on this level of inventiveness  :|||:

Richard
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

HallelujahAl

  • Guest
Re: Daft Hohner Project...biting off more than I can chew?
« Reply #9 on: September 30, 2010, 08:21:13 PM »

Soldering iron worked for me - cost me £2.50 from a cheapie shop. Still working actually.
 ;D
AL
Logged

Jon Loomes

  • Performer, Recording Engineer, Luthier.
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 115
  • Non plaudite. Pecuniam jacite.
    • www.jonloomes.com
Re: Daft Hohner Project...biting off more than I can chew?
« Reply #10 on: September 30, 2010, 09:44:23 PM »

Well, Nicky Clarke won the day....both mechanisms now removed with buttons preserved for later...

Having thought it al through a bit more (and given the limited tools at my disposal pending moving house)  I'm actually going to drill new holes in the original soundboard rather than do the graft and transfer. This will mean that I have to make new a new reed block for the chords and reverse the triangle pallet direction, but at least if I bugger it up I can put the pallets back the right way and have another go with the graft method.  Or make a new board.  Just trimming felts and leathers now. Next job will be to fill the old holes in the LH of the casework and drill new ones to accommodate 12 basses and get rid of the annoying p accordion slant between the rows.

Cheers,
J

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Daft Hohner Project...biting off more than I can chew?
« Reply #11 on: October 01, 2010, 01:41:58 AM »

Am I correct in thinking that our Rees did Simon Ritchie's Student 1 conversion?.


Tim "Banjo" Normanton did all the horrid casework and action stuff, I just supplied the various knackered instruments and fitted the reeds and blocks.
As I recall, the melodeon keyboard was riddled with woodworm so Tim kind of rebuilt it with fibreglass.
Simon loves it!
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Jon Loomes

  • Performer, Recording Engineer, Luthier.
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 115
  • Non plaudite. Pecuniam jacite.
    • www.jonloomes.com
Re: Daft Hohner Project...biting off more than I can chew?
« Reply #12 on: October 02, 2010, 10:45:55 PM »

"Next job will be to fill the old holes in the LH of the casework and drill new ones to accommodate 12 basses and get rid of the annoying p accordion slant between the rows."

Done... well, half done. Not drilling the outer row holes till the filler in the old holes has set properly.  Suddenly, it's starting to take shape, though.

Jon Loomes

  • Performer, Recording Engineer, Luthier.
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 115
  • Non plaudite. Pecuniam jacite.
    • www.jonloomes.com
Re: Daft Hohner Project...biting off more than I can chew?
« Reply #13 on: October 10, 2010, 09:34:57 PM »

Well....it looks like a melodeon, and a most pretty one at that.  But the L/H mechanism is awful.  Truly horrid.  Everything is bent (ooooh, Jules! a bona hohner...) and twisted, (a word, dear reader you may note, that has already been used in this thread.  R/H coming on nicely though, except the only treble blocks I can find are a set I tuned to G natural min in order to learn how to tune reeds. So it's all a bit odd at the minute.  I'm half tempted to fill in the extra bass holes in the carcass and go back to 8 bass, but I can't help feeling that that's maybe a bit defeatist.  Am I better off quitting while I'm only a bit behind? Oh reader, what shall I do?

Tamba

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 294
  • Busilacchio
Re: Daft Hohner Project...biting off more than I can chew?
« Reply #14 on: October 10, 2010, 09:37:25 PM »

Keep calm and carry on!
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal