Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Faceplates (soundboards?)  (Read 6167 times)

0 Members and 1 Guest are viewing this topic.

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Faceplates (soundboards?)
« on: October 23, 2010, 03:13:49 PM »

Since there are folks from round the globe on this forum, excuse my terminology, but hopefully you'll know what I'm talking about.

I went through all the available threads on here, and saw some interesting stuff, I'll try not to rehash the same old stuff, but a few things I was hoping to learn more about.

What I call faceplates, I've seen referred to here as soundboards.  They are commonly made of aircraft plywood in my area, undoubtedly mainly due to stability.  I am curious of the tone difference in using non laminated lumber.  I see the intrinsic problems in using lumber in such thin dimensions where vibrations are constant and flatness is required.  But it is held, at least to some degree it's full perimeter.  Anyone here have experience in using solid non laminated faceplates?  Is there any difference to you in terms of tone and/or volume?

The variables that affect both tone and volume in these contraptions is mind boggling, but fascinating.

Bryan Lafleur

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Faceplates (soundboards?)
« Reply #1 on: October 23, 2010, 03:18:12 PM »

The biggest structural problem is the weakness between the 'air holes'  whichever direction you run the grain you end up with the grain running directly between holes which could be prone to split.  Castagnari used solid spruce or western red cedar in the Casta.  Lovely sounding instruments, but no longer made.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Mike Averill

  • suffering from MAD
  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 325
Re: Faceplates (soundboards?)
« Reply #2 on: October 23, 2010, 07:12:28 PM »

You might also consider aluminium. Castagnari, Sonola, vintage Hohner etc have all used it in some quite nice boxes,  resulting in a quite bright sound.
Logged
Hohner - 1 row 4 stop C and G, pokerwork DG, DoubleRay DC#, Corso CC#, Corona III ADG, CLUB X CF, Elysium II CF
Saltarelle 1 row 4 stop D, Castagnari Giordy DG, Sander DG
Sonola CC#, Walters DC#

Andy in Vermont

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 948
  • Mélodie
    • Melodeon Minutes (blog)
Re: Faceplates (soundboards?)
« Reply #3 on: October 23, 2010, 09:18:45 PM »

But it is held, at least to some degree it's full perimeter.  Anyone here have experience in using solid non laminated faceplates? 

Hi Bryan,
I've been experimenting with the structural issues -- haven't completed the instrument yet but have a "tone" and volume related experiment planned.
Brico Diato -- a column in a French magazine -- deals with accordion maintenance, and several years back, the author dealt with the structural issues on a solid "soundboard" ("fondo" is perhaps a better term) on a box where the fondo had warped, causing the pallets to lose airtightness -- and perhaps the reedblocks also lost good contact, I don't recall.  His solution IIRC was to add some internal bracing across the grain.
I seem to recall someone mentioning that the "Casta" model that Theo mentioned above had some structural issues?  I corresponded with Castagnari regarding this model and at the time, they told me that the design revolved around "acoustic considerations."
One option is to glue-up three narrow boards -- edge-jointed.
-Andy

Andy Simpson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 938
Re: Faceplates (soundboards?)
« Reply #4 on: October 23, 2010, 11:32:01 PM »

I seem to recall someone mentioning that the "Casta" model that Theo mentioned above had some structural issues?  I corresponded with Castagnari regarding this model and at the time, they told me that the design revolved around "acoustic considerations."
One option is to glue-up three narrow boards -- edge-jointed.

That might have been me saying that I wondered how the solid WRC panels on Castas were going to hold up in years to come.

I suspect that the "tonewood soundboards" do make difference but not for the reason most people would think. Ironically, they may make the instrument sound "better" to the ear by being, (technically-speaking), worse than a plywood board.



« Last Edit: October 23, 2010, 11:37:34 PM by Andy Simpson »
Logged

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: Faceplates (soundboards?)
« Reply #5 on: October 24, 2010, 02:04:40 AM »

The bridge plate of a folk guitar has holes drilled in it for the strings, quite close together. The steel strings are anchored to the underside of the s.b. against this unseen plate between a metal ring on the end of the string and the end of the bridge pin.

Such plates are prone to cracking because the plate is very thin and the holes are close to one another. Luthiers and repairmen cut new bridge plates with the grain running 45 degrees to the orientation of the strings/plate to avoid having the plate crack  with the grain either between holes or at right angles to them. It works well, but almost always requires replacement after decades of service.

My concern for using edge jointed planks in a thin, solid wood fondo is keeping the assembly perfectly flat during glue up. I'm not sure how the whole thing would affect the tone, though. Making the holes more square than round might help, and may also help structurally provided the running edges of the holes were not parallel to the grain of the board.   

Andy Simpson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 938
Re: Faceplates (soundboards?)
« Reply #6 on: October 24, 2010, 04:26:31 AM »

My concern for using edge jointed planks in a thin, solid wood fondo is keeping the assembly perfectly flat during glue up.  

Not a problem whatsoever. They cracked that one hundreds of years ago gluing up soundboards for flat top instruments.

Also, my preferred term for them in English would be something like baseboard. Fondo just means bottom in Italian and over the last thousand years there's been quite enough elevation of mundane words from other languages into specialised terms that obscure the nature of something that can be rendered perfectly clearly in English. ;D

Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Faceplates (soundboards?)
« Reply #7 on: October 24, 2010, 10:01:56 AM »

In French they call it "table".
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Andy in Vermont

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 948
  • Mélodie
    • Melodeon Minutes (blog)
Re: Faceplates (soundboards?)
« Reply #8 on: October 24, 2010, 03:06:53 PM »

My concern for using edge jointed planks in a thin, solid wood fondo is keeping the assembly perfectly flat during glue up.

Well, the Castagnari one-row that I had featured a glued-up fondo, and it held up for years, so that should be some indication that it is a possibility.
Your concern about keeping glue-ups flat during glue-up is a non-concern: since you've done at least basic joinery that included glue-ups, you will have had the experience that flattening AFTER glue-up is simple, especially with a small component like this.  If the component is too wide for your jointer and/or planer, then I suggest learning how to use a well-fettled handplane.  There are many techniques to simplify this.  My favorite is to hand-plane the faces of the boards to a slight hollow, so that the point where they glue together becomes a high spot.  Glue up the boards, then a few passes with a plane set to take a very fine shaving should bring the boards into flat.  However, with a very small glue-up such as the one contemplated, I'd probably just start with boards that are slightly thicker than the target, then plane them flat

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Faceplates (soundboards?)
« Reply #9 on: October 24, 2010, 04:58:33 PM »

I agree, Andy, if I do it it will be with a glued up panel, made thicker then brought down on my thickness sander (I love that thing).  I had heard Marc Savoy say that cracking between the holes was a common occurrence on the old German Sterlings and Monarchs, but I was actually more concern with warping, even a little, creating valve seating problems.  My other concern is if sliding stops are used, it would require a backing plate for the reed blocks, which will open up more possible problems.  Easy to see why its so much easier to use plywood.  Never have seen one with metal plates.

The worst part of this type of experiment, is it would take years to know the actual effects.

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Faceplates (soundboards?)
« Reply #10 on: October 24, 2010, 05:14:50 PM »

So what does make a good soundboard? Do you want one that will transmit vibrations to the body or not? I have absolutely no idea what makes a good accordion, acoustically :-\
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: Faceplates (soundboards?)
« Reply #11 on: October 24, 2010, 07:38:49 PM »

My concern for using edge jointed planks in a thin, solid wood fondo is keeping the assembly perfectly flat during glue up.

Well, the Castagnari one-row that I had featured a glued-up fondo, and it held up for years, so that should be some indication that it is a possibility.
Your concern about keeping glue-ups flat during glue-up is a non-concern: since you've done at least basic joinery that included glue-ups, you will have had the experience that flattening AFTER glue-up is simple, especially with a small component like this.  If the component is too wide for your jointer and/or planer, then I suggest learning how to use a well-fettled handplane.  There are many techniques to simplify this.  My favorite is to hand-plane the faces of the boards to a slight hollow, so that the point where they glue together becomes a high spot.  Glue up the boards, then a few passes with a plane set to take a very fine shaving should bring the boards into flat.  However, with a very small glue-up such as the one contemplated, I'd probably just start with boards that are slightly thicker than the target, then plane them flat

I'm aware how it could be done (a hand plane to flatten for something this size) but why bother? If it'd have to be done at all - which seems like a lot more work for, possibly, little or negligible change in the tone of the accordion. A piece of plywood cut to size seems like it'd be a much simpler solution, that's all.

Mike Averill

  • suffering from MAD
  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 325
Re: Faceplates (soundboards?)
« Reply #12 on: October 24, 2010, 07:59:25 PM »

Easy to see why its so much easier to use plywood.  Never have seen one with metal plates.

The Castagnari Sander is a typical metal plate example.

Quote
The worst part of this type of experiment, is it would take years to know the actual effects.
Look for read across from other instruments. Take the anglo concertina, they have boards of real quarter sawn wood, plenty example around that are 100 years plus. They only warp if you leave them in bits. Keep them assembled at all times and no problems.

Logged
Hohner - 1 row 4 stop C and G, pokerwork DG, DoubleRay DC#, Corso CC#, Corona III ADG, CLUB X CF, Elysium II CF
Saltarelle 1 row 4 stop D, Castagnari Giordy DG, Sander DG
Sonola CC#, Walters DC#

Andy in Vermont

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 948
  • Mélodie
    • Melodeon Minutes (blog)
Re: Faceplates (soundboards?)
« Reply #13 on: October 24, 2010, 08:02:28 PM »

I'm aware how it could be done (a hand plane to flatten for something this size) but why bother? If it'd have to be done at all - which seems like a lot more work for, possibly, little or negligible change in the tone of the accordion. A piece of plywood cut to size seems like it'd be a much simpler solution, that's all.

For the same reason I don't make my burgers the same as McDonalds!

Andy in Vermont

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 948
  • Mélodie
    • Melodeon Minutes (blog)
Re: Faceplates (soundboards?)
« Reply #14 on: October 24, 2010, 08:07:08 PM »

The Castagnari Sander is a typical metal plate example.
[...]
Take the anglo concertina, they have boards of real quarter sawn wood, plenty example around that are 100 years plus. They only warp if you leave them in bits. Keep them assembled at all times and no problems.

Many Castagnari models have metal fondos.  At some point I recall looking at a European-made box that had wood laminated on one side of a metal fondo.
I'm not sure that the anglo is the right source to determine if warping can occur.  First of all, it is a much smaller surface that a Cajun-sized accordion.  It is also held in place in a different manner -- although a similar technique could be implemented on a Cajun box, I suppose, with some design changes.
Finally, are you sure that the warped ones (I've seen several examples) all occurred when concertinas were stored as disassembled parts?

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: Faceplates (soundboards?)
« Reply #15 on: October 24, 2010, 10:56:24 PM »

I'm aware how it could be done (a hand plane to flatten for something this size) but why bother? If it'd have to be done at all - which seems like a lot more work for, possibly, little or negligible change in the tone of the accordion. A piece of plywood cut to size seems like it'd be a much simpler solution, that's all.

For the same reason I don't make my burgers the same as McDonalds!

Fair enough. Using a sharp plane is a joy, too.  (:)

Andy in Vermont

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 948
  • Mélodie
    • Melodeon Minutes (blog)
Re: Faceplates (soundboards?)
« Reply #16 on: October 25, 2010, 11:34:26 AM »

Fair enough. Using a sharp plane is a joy, too.  (:)

Amen!

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Faceplates (soundboards?)
« Reply #17 on: October 25, 2010, 04:44:53 PM »

So I'm not the only one that the sound and feel of a sharp well tuned hand plane slicing wood brings a smile to?

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Faceplates (soundboards?)
« Reply #18 on: October 25, 2010, 05:27:32 PM »

Indeed not.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Andy in Vermont

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 948
  • Mélodie
    • Melodeon Minutes (blog)
Re: Faceplates (soundboards?)
« Reply #19 on: October 25, 2010, 06:40:45 PM »

Indeed not.

It's even better when you've made the plane yourself!
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal