Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 [3] 4 5 6 7 8   Go Down

Author Topic: Refurbishing an old Hohner  (Read 64990 times)

0 Members and 1 Guest are viewing this topic.

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #40 on: June 06, 2008, 11:26:05 PM »

All available!
An order is in the offing. ;D  I'll have plenty to keep me busy with the reedwork in the meantime so I'll let you know what I want and then collect it in a couple of weeks time on the way up to Northumberland (or perhaps on the way back down a few days later depending how things pan out).

I tackled the treble keyboard last night and again today. The thumb groove on the edge was a twenty minute job with a half round wood rasp followed by a various grades of sandpaper wrapped around a 50mm o.d. socket. It's fairly shallow to be honest but it does the job without going too deeply into the relatively thin timber on the outer edge. A bit of black stain and a couple of coats of satin varnish rubbed down with 0000 grade wire wool dipped in beeswax and then lightly buffed to finish, job done and looking pretty good.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #41 on: June 11, 2008, 09:29:15 PM »

Tuning has started on the basses and after a bit of confusion (explained to me by ever patient Theo), continues. Now I'm thinking about the treble reeds and have a question about the order in which they are fitted. This is a three voice MMM box with three blocks of reeds in the treble end. The first block has eleven reeds on each side relating to the outer row, the second block has eleven on one side (outer row) and ten on the other (inner row) the third block has ten reeds on each side - inner row again.

Is there a conventional layout in the rows? ie 1st flat, 2nd even, 3rd sharp - 4th flat, 5th even, 6th sharp (or the reverse order within each set) or might they be in any old order?

Last question for this post; most three voice MMM boxes are musette tuned which is a bit too wet for my liking so how many cents flat and sharp should I go to have a lively vibrato with going into the realms of musette?
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Refurbishing an old Hohner
« Reply #42 on: June 11, 2008, 10:55:14 PM »

Is there a conventional layout in the rows? ie 1st flat, 2nd even, 3rd sharp - 4th flat, 5th even, 6th sharp (or the reverse order within each set) or might they be in any old order?

It only really matters if your box has stops or couplers.  I usually mark the blocks before I take the reeds off.

Quote
Last question for this post; most three voice MMM boxes are musette tuned which is a bit too wet for my liking so how many cents flat and sharp should I go to have a lively vibrato with going into the realms of musette?

There is also the question of whether you have the reeds tuned an equal distance apart, or a different distance apart.  Many Italian boxes have about twice the difference between mid an high as between mid and low.  It makes a noticeable difference to the sound.

As to how much - well I think you need to do some trials and see what sound you like.  Do the reeds for a few notes and listen to the sound they make together,  adjust drier or wetter till you find what you like.  That is the big advantage of doing your own tuning.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

GuyWyatt

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 303
Re: Refurbishing an old Hohner
« Reply #43 on: June 12, 2008, 08:24:51 AM »

Any ideas how many man-hours (person-hours) you are up to on this project so far?
Guy
Logged

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #44 on: June 12, 2008, 08:03:54 PM »

Hello Guy, it's a bit difficult to quantify to be honest due to the way I go about jobs like this, in bits and pieces here and there with occasional bursts of constant activity. I often spent a few minutes during tea breaks at work pealing off bindings etc and up to twenty minutes of my lunch breaks each day were also spent beavering away, much to the amusement of my colleagues.

The bellows alone occupied some sixteen hours or so, what I haven't mentioned earlier is that I cut out and fitted 76 pieces of very thin leather 51mm long and 20mm wide with radiused ends fitting inside the metal corners to reinforce the gussets; this took quite a long time!

The pallets took a couple of hours to remove, clean, fit new felt/leather pads and refit. Another couple of hours or so were spent tidying up and refinishing the woodwork of the fingerboard, fitting new padded strips under the levers to limit travel, leveling the keys, cleaning and spraying the front grille and sorting out the celluloid.

So far about four hours on the reeds with little to show for it because I spent much of the time scratching my head.  ??? The project will slow down drastically now because I can only work at home and I need to have sufficient spare time to make it worthwhile dragging out the tuning rig and setting it up - so not less than a couple of hours at a stretch which is hard to come by through the week.

Best guess so far then is about 24 hours to get to this stage, which tends to suggest I'm either dedicated, very sad or stark staring mad; or indeed all of the above.  ::)

Pete.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #45 on: June 14, 2008, 07:25:09 PM »

I bought some nice material to put inside the grilles but the pics look quite odd using embedded links. To see the pics properly view the whole album page here




Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #46 on: June 14, 2008, 07:54:49 PM »

There is also the question of whether you have the reeds tuned an equal distance apart, or a different distance apart.  Many Italian boxes have about twice the difference between mid an high as between mid and low.  It makes a noticeable difference to the sound.

As to how much - well I think you need to do some trials and see what sound you like.  Do the reeds for a few notes and listen to the sound they make together,  adjust drier or wetter till you find what you like.  That is the big advantage of doing your own tuning.

I'm a bit confused as to how I achieve this. If, for arguments sake I decide to wax the reeds back in, does this mean I have to wax them in and then rebuild the melodeon just to listen to it and then if I don't like the sound dig the reed plates back out and try again? Isn't there a rough guide as to how many cents +/- will give a tremolo more pronounced than swing but less than musette? Oh, and I like the sound of my Italian box (albeit LMM) so the idea of weighting the offset tuning more on the sharp reed than the flat one is quite appealing.

Incidentally I've noted your comments about tuning the thirds -5 cents in the chord reed set so I'll be doing that. On the larger bass reeds should I have tuned them exactly an octave apart (which I have) or should the higher reed have been slightly sharp for tremolo?
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Refurbishing an old Hohner
« Reply #47 on: June 14, 2008, 10:17:00 PM »

I bought some nice material to put inside the grilles but the pics look quite odd using embedded links.
How did you fix the new cloth in place? - Just picked up my "new" Hohner Club which needs a new grille cloth :-)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #48 on: June 14, 2008, 11:07:31 PM »

How did you fix the new cloth in place? - Just picked up my "new" Hohner Club which needs a new grille cloth :-)
Not my favourite adhesive, but on this occasion I used Copydex. Latex is very forgiving so if you make a right mess of it you can just peal it off and start again.

As for the material I picked it up in a local art and craft shop. It's used as the base for cross stitching (whatever that is!  ::) ). Sounds quite expensive, one metre wide and £12 per running metre. I bought half a running metre for £6 and that's enough for at least four melodeons with enough left in the offcuts for a concertina or two; a bargain I reckon.

PM me your address Lester and I'll send you enough for your new box. Do bear in mind it will cost you a pint of beer should we ever meet up...  ;)
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Refurbishing an old Hohner
« Reply #49 on: June 14, 2008, 11:38:01 PM »

PM me your address Lester and I'll send you enough for your new box. Do bear in mind it will cost you a pint of beer should we ever meet up...  ;)
Thanks for your kind offer but my wife is a v keen canvas embroiderer so already have a loft full.

Example of the Sainted Mrs Bailey's work

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #50 on: June 15, 2008, 12:04:56 AM »

Thanks for your kind offer but ...
Ah, closet Yorkshireman are you? As a proper Yorkshireman I can sympathise, damned expensive stuff, beer.  :P
Quote
Example of the Sainted Mrs Bailey's work
Great stuff! It's wonderful to see craft work that is made for love, goodness knows you could never make a profit from it. It's said that pride is a sin but I don't really believe that; if you create something that has beauty beyond price and derive pleasure from its' creation and revel in your own skill at making it is that so very bad?
« Last Edit: June 15, 2008, 09:26:56 AM by tallship »
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Refurbishing an old Hohner
« Reply #51 on: June 15, 2008, 12:19:43 PM »


T On the larger bass reeds should I have tuned them exactly an octave apart (which I have) or should the higher reed have been slightly sharp for tremolo?

The last thing you need is tremolo on your basses so tune them all to zero (or top dead centre as we say in Wales).
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #52 on: June 15, 2008, 08:20:27 PM »

The last thing you need is tremolo on your basses so tune them all to zero (or top dead centre as we say in Wales).

Thanks Rees, I've done just that. The first eight plates (the lowest) are now done, two of the reeds had to be tuned down by five semitones which is quite a fundamental change.  :o

I was a little concerned that the soldering iron might overheat the reeds and affect the tempering but my fears were unfounded and this part of the procedure was probably the easiest and quickest of all. Chord reeds next but it will be a fortnight at the earliest before I get around to starting those because I'm going off on holiday next weekend (hooray!). At this rate the box might be finished by September/October.  ::)
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Andy Next Tune

  • aka Andy Wooles
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1127
  • Melodeon with Accidentals? Make a PI Claim!!!
    • www.shavethedonkey.co.uk
Re: Refurbishing an old Hohner
« Reply #53 on: June 15, 2008, 11:19:57 PM »


Thanks for your kind offer but my wife is a v keen canvas embroiderer so already have a loft full.

Example of the Sainted Mrs Bailey's work
[/quote]
Thanks for reminding me about the Betley Court window Lester. I remember seeing it in the V&A a number of years ago, long before I reacquainted myself with the Morris and the Pokerwork melodeon then in semi-retirement.

And as someone who has cross-stitched in the past, that's a great piece of work by your wife.

Andy

Logged
Andy, from the now ex-County Palatine of Cheshire

Caring for a European community of melodeons from France, Italy, Germany, Wales and Suffolk!

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Refurbishing an old Hohner
« Reply #54 on: June 15, 2008, 11:44:26 PM »

When applying solder to  large reeds to lower the pitch you can make a heatsink by using a small crocodile clip with a lump of copper between the jaws.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Refurbishing an old Hohner
« Reply #55 on: June 16, 2008, 09:36:31 AM »

I'm a bit confused as to how I achieve this. If, for arguments sake I decide to wax the reeds back in, does this mean I have to wax them in and then rebuild the melodeon just to listen to it and then if I don't like the sound dig the reed plates back out and try again?

You tune the reeds after they have been waxed in.   The pitch can change by an appreciable amount once they are mounted, compared with on a tuning bench.  You need some nifty tools to get access to the pull reeds. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #56 on: June 16, 2008, 06:57:10 PM »

You need some nifty tools to get access to the pull reeds. 

:o Oh dear, I think I'm getting one of my headaches.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Refurbishing an old Hohner
« Reply #57 on: June 16, 2008, 07:09:28 PM »

You need some nifty tools to get access to the pull reeds. 

:o Oh dear, I think I'm getting one of my headaches.

If you can get to Whitby Folk Week I'll show you how its done.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #58 on: June 16, 2008, 08:31:32 PM »

I've sent you a PM Theo.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #59 on: July 06, 2008, 11:04:43 PM »

Well the holiday was great, not least because I got to call in on Theo to collect a few bits and watch in amazement as he demonstrated one or two of the black arts of tuning. Secret and coveted knowledge? not a bit of it! Buy one of these from here and use it like this, don't blink mind or you've missed it. Too slow? I'll show you again!

A visit to Theo is always a pleasure and a great education, you can't fail to be caught up in his enthusiasm for all things to do with free reeds; he even meddles with concertinas you know, poor man.

I should have been back at work on the Hohner this weekend but the tuning rig is a bit too large for the kitchen. Scraping wax off reed plates is messy too and the rain prevented me from working outside so I decided to start work on tuning an old anglo concertina for a bit of light relief. Not the best relaxation plan I've come up with!
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)
Pages: 1 2 [3] 4 5 6 7 8   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal